temperature sensor NISSAN X-TRAIL 2005 Service Repair Manual

GI-6
PRECAUTIONS

CAUTION:

Do not use home heating oil, gasoline or other alternate fuels in your diesel engine. The use of
those can cause engine damage.

Do not use summer fuel at temperatures below –7°C (20°F). The cold temperatures will cause wax
to form in the fuel. As a result, it may prevent the engine from running smoothly.

Do not add gasoline or other alternate fuels to diesel fuel.
Precautions for Multiport Fuel Injection System or Engine Control SystemEAS000FT

Before connecting or disconnecting any harness connector for
the multiport fuel injection system or ECM:
Turn ignition switch to “OFF” position.
Disconnect negative battery terminal.
Otherwise, there may be damage to ECM.

Before disconnecting pressurized fuel line from fuel pump to
injectors, be sure to release fuel pressure.

Be careful not to jar components such as ECM and mass air
flow sensor.
Precautions for Turbocharger (If Equipped)EAS000FU
The turbocharger turbine revolves at extremely high speeds and
becomes very hot. Therefore, it is essential to maintain a clean sup-
ply of oil flowing through the turbocharger and to follow all required
maintenance instructions and operating procedures.

Always use the recommended oil. Follow the instructions for
proper time to change the oil and proper oil level.

Avoid accelerating engine to a high rpm immediately after start-
ing.

If engine had been operating at high rpm for an extended period
of time, let it idle for a few minutes prior to shutting if off.
Precautions for HosesEAS000FV
HOSE REMOVAL AND INSTALLATION

To prevent damage to rubber hose, do not pry off rubber hose
with tapered tool or screwdriver.

To reinstall the rubber hose securely, make sure that hose inser-
tion length and orientation is correct. (If tube is equipped with
hose stopper, insert rubber hose into tube until it butts up
against hose stopper.)
SGI787
SGI292
SMA019D
SMA020D

GI-48
TERMINOLOGY

TERMINOLOGYPFP:00011
SAE J1930 Terminology List EAS000GH
All emission related terms used in this publication in accordance with SAE J1930 are listed. Accordingly, new
terms, new acronyms/abbreviations and old terms are listed in the following chart.
NEW TERMNEW ACRONYM /
ABBREVIATIONOLD TERM
Air cleaner ACL Air cleaner
Barometric pressure BARO ***
Barometric pressure sensor-BCDD BAROS-BCDD BCDD
Camshaft position CMP ***
Camshaft position sensor CMPS Crank angle sensor
Canister *** Canister
Carburetor CARB Carburetor
Charge air cooler CAC Intercooler
Closed loop CL Closed loop
Closed throttle position switch CTP switch Idle switch
Clutch pedal position switch CPP switch Clutch switch
Continuous fuel injection system CFI system ***
Continuous trap oxidizer system CTOX system ***
Crankshaft position CKP ***
Crankshaft position sensor CKPS ***
Data link connector DLC ***
Data link connector for CONSULT-II DLC for CONSULT-II Diagnostic connector for CONSULT-II
Diagnostic test mode DTM Diagnostic mode
Diagnostic test mode selector DTM selector Diagnostic mode selector
Diagnostic test mode I DTM I Mode I
Diagnostic test mode II DTM II Mode II
Diagnostic trouble code DTC Malfunction code
Direct fuel injection system DFI system ***
Distributor ignition system DI system Ignition timing control
Early fuel evaporation-mixture heater EFE-mixture heater Mixture heater
Early fuel evaporation system EFE system Mixture heater control
Electrically erasable programmable read
only memoryEEPROM ***
Electronic ignition system EI system Ignition timing control
Engine control EC ***
Engine control module ECM ECCS control unit
Engine coolant temperature ECT Engine temperature
Engine coolant temperature sensor ECTS Engine temperature sensor
Engine modification EM ***
Engine speed RPM Engine speed
Erasable programmable read only memory EPROM ***
Evaporative emission canister EVAP canister Canister
Evaporative emission system EVAP system Canister control solenoid valve
Exhaust gas recirculation valve EGR valve EGR valve

TERMINOLOGY
GI-49
C
D
E
F
G
H
I
J
K
L
MB
GI

Exhaust gas recirculation control-BPT
valveEGRC-BPT valve BPT valve
Exhaust gas recirculation control-solenoid
valveEGRC-solenoid valve EGR control solenoid valve
Exhaust gas recirculation temperature sen-
sor
EGRT sensor Exhaust gas temperature sensor
EGR temperature sensor
Flash electrically erasable programmable
read only memoryFEEPROM ***
Flash erasable programmable read only
memoryFEPROM ***
Flexible fuel sensor FFS ***
Flexible fuel system FF system ***
Fuel pressure regulator *** Pressure regulator
Fuel pressure regulator control solenoid
valve*** PRVR control solenoid valve
Fuel trim FT ***
Heated Oxygen sensor HO2S Exhaust gas sensor
Idle air control system IAC system Idle speed control
Idle air control valve-air regulator IACV-air regulator Air regulator
Idle air control valve-auxiliary air control
valveIACV-AAC valve Auxiliary air control (AAC) valve
Idle air control valve-FICD solenoid valve IACV-FICD solenoid valve FICD solenoid valve
Idle air control valve-idle up control sole-
noid valveIACV-idle up control solenoid valve Idle up control solenoid valve
Idle speed control-FI pot ISC-FI pot FI pot
Idle speed control system ISC system ***
Ignition control IC ***
Ignition control module ICM ***
Indirect fuel injection system IFI system ***
Intake air IA Air
Intake air temperature sensor IAT sensor Air temperature sensor
Knock *** Detonation
Knock sensor KS Detonation sensor
Malfunction indicator lamp MIL Check engine light
Manifold absolute pressure MAP ***
Manifold absolute pressure sensor MAPS ***
Manifold differential pressure MDP ***
Manifold differential pressure sensor MDPS ***
Manifold surface temperature MST ***
Manifold surface temperature sensor MSTS ***
Manifold vacuum zone MVZ ***
Manifold vacuum zone sensor MVZS ***
Mass air flow sensor MAFS Air flow meter
Mixture control solenoid valve MC solenoid valve Air-fuel ratio control solenoid valve
Multiport fuel injection System MFI system Fuel injection controlNEW TERMNEW ACRONYM /
ABBREVIATIONOLD TERM

EM-210
[YD22DDTi]
CYLINDER HEAD

10. Complete this operation as follows:
a. Turn the ignition switch to “OFF”.
b. Disconnect the battery cable from the negative terminal.
c. Install glow plug and install all the parts removed in step 4.
d. Install fuel pump fuse [ENG CONT (20A)].
e. Connect the battery cable to the negative terminal.
f. Using CONSULT-II make sure no DTC is indicated for items of self-diagnosis.
Removal and InstallationEBS00LRW
REMOVAL
1. Drain engine coolant. Refer to CO-32, "Changing Engine Coolant" .
2. Remove the following:

Charge air cooler (Refer to EM-144, "Removal and Installation" .)

Rocker cover (Refer to EM-178, "Removal and Installation" .)

Air cleaner and air duct (Refer to EM-142, "Removal and Installation" .)

Vacuum pump (Refer to EM-163, "Removal and Installation" .)

Spill tube and fuel injector (Refer to EM-167, "Removal and Installation" .)

Intake manifold (Refer to EM-146, "Removal and Installation" .)

Exhaust manifold and turbocharger (Refer to EM-151, "Removal and Installation" .)

Secondary timing chain (Refer to EM-193, "Removal and Installation" .)

Camshaft (Refer to EM-180, "Removal and Installation" .)
3. Remove cylinder head assembly.
1. Glow plug 2. Cylinder head assembly 3. Cylinder head bolt
4. Copper washer 5. Engine coolant temperature sensor 6. Gasket
7. Water outlet 8. Dowel pin 9. Cylinder gasket
10. Glow harness 11. Glow plate 12. Cap
PBIC2437E

SERVICE DATA AND SPECIFICATIONS (SDS)
EM-267
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
EM

*1 Rocker cover1)
7.8 (0.8, 69)*2
2)
7.8 (0.8, 69) *2
*1 Camshaft bracket 13 to 15 bolts 1) 2 (0.2, 1)
1 to 12 bolts 2) 2 (0.2, 1)
3) 6 (0.6, 4)
4) 12.5 (1.3, 9)
*1 Front chain case
7.9 (0.8, 70)*
2
Chain tensioner
9.6 (0.98, 85)*2
Tension guide23.5 (2.4, 18)
Slack guide23.5 (2.4, 18)
Camshaft sprocket 143 (15, 105)
*1 Oil pump housing12.5 (1.3, 9)
Power steering oil pump 53.5 (5.5, 39)
*1 Rear chain case12.5 (1.3, 9)
Engine coolant temperature sensor 13.5 (1.4, 10)
*1 Cylinder head 1) 39.2 (4.0, 29)
2) 180 degrees
3) 0 (0, 0)
4) 39.2 (4.0, 29)
5) 90 degrees (angle tightening)
6) 90 degrees (angle tightening)
Glow plug20.5 (2.1, 15)
*1 Flywheel108 (11, 80)
Oil pressure switch15 (1.5, 11)
Oil jet
8.4 (0.86, 74)*
2
Oil jet relief valve49 (5.0, 36)
Rear oil seal retainer12.5 (1.3, 9)

THERMOSTAT AND WATER CONTROL VALVE
CO-23
[QR]
C
D
E
F
G
H
I
J
K
L
MA
CO

THERMOSTAT AND WATER CONTROL VALVEPFP:21200
Removal and InstallationEBS00KOO
REMOVAL
1. Drain engine coolant. Refer to CO-9, "Changing Engine Coolant" .
CAUTION:

Perform this step when engine is cold.

Do not spill engine coolant on drive belt.
2. Disconnect radiator hose (lower) at water inlet side. Refer to CO-12, "
RADIATOR" .
3. Remove water inlet and thermostat.
4. Remove water control valve with the following procedure:
a. Disconnect radiator hose (upper) at water control valve housing (water outlet) side.
b. Disconnect harness connector from engine coolant temperature sensor.
c. Disconnect water hoses.
d. Remove heater pipe and heater hose.
e. After removing water control valve housing (water outlet) and water control valve.
1. Thermostat 2. O-ring 3. Water inlet
4. Water control valve 5. O-ring 6. Gasket
7. Water control valve housing (water outlet) 8. Washer 9. Engine coolant temperature sensor
10. Water hose 11. Heater hose 12. O-ring
13. Heater pipe 14. Water hose 15. Heater hose
PBIC3597E

SERVICE DATA AND SPECIFICATIONS (SDS)
CO-25
[QR]
C
D
E
F
G
H
I
J
K
L
MA
CO

SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
Standard and LimitEBS00KOP
CAPACITY
Unit: (lmp qt)
RADIATOR
Unit: kPa (bar, kg/cm2 , psi)
THERMOSTAT
WATER CONTROL VALVE
*: Reference data
Tightening TorqueEBS00KOQ
Unit: N·m (kg-m, ft-lb)
Unit: N·m (kg-m, in-lb)*
Engine coolant capacity (With reservoir tank at “MAX” level) Approx. 7.1 (6-1/4)
Reservoir tank0.7 (5/8)
Cap relief pressureStandard 78 - 98 (0.78 - 0.98, 0.8 - 1.0, 11- 14)
Limit 59 (0.59, 0.6, 9)
Leakage test pressure 157 (1.57, 1.6, 23)
Valve opening temperature 80.5 - 83.5°C (177 - 182°F)
Maximum valve lift 8 mm/ 95°C (0.315 in/ 203°F)
Valve closing temperature 77°C (171°F)
Valve opening temperature 93.5 - 96.5°C (200 - 206°F)
Maximum valve lift 8 mm/ 108°C (0.315 in/ 226°F)*
Valve closing temperature 90°C (194°F)
Radiator mounting bracket 5.5 (0.56, 49)*
Radiator cooling fan assembly 5.5 (0.56, 49)*
Cooling fan3.43 (0.35, 30)*
Fan motor4.41 (0.45, 39)*
Water pump24.5 (2.5, 18)
Water pump housing28.0 (2.9, 21)
Water pipe28.0 (2.9, 21)
Water inlet28.0 (2.9, 21)
Water control valve housing (water outlet) 28.0 (2.9, 21)
Hater pipe28.0 (2.9, 21)
Engine coolant temperature sensor 24.5 (2.5, 18)

EC-4 CONSULT-II Reference Value in Data Monitor Mode
.306
On Board Diagnosis Logic ....................................306
DTC Confirmation Procedure ...............................306
Wiring Diagram .....................................................308
Diagnostic Procedure ...........................................311
Component Inspection ..........................................313
DTC P1128 THROTTLE CONTROL MOTOR .........314
Component Description ........................................314
On Board Diagnosis Logic ....................................314
DTC Confirmation Procedure ...............................314
Wiring Diagram .....................................................315
Diagnostic Procedure ...........................................319
Component Inspection ..........................................320
Removal and Installation ......................................321
DTC P1143 HO2S1 .................................................322
Component Description ........................................322
CONSULT-II Reference Value in Data Monitor Mode
.322
On Board Diagnosis Logic ....................................322
DTC Confirmation Procedure ...............................323
Overall Function Check ........................................323
Diagnostic Procedure ...........................................324
Component Inspection ..........................................326
Removal and Installation ......................................327
DTC P1144 HO2S1 .................................................328
Component Description ........................................328
CONSULT-II Reference Value in Data Monitor Mode
.328
On Board Diagnosis Logic ....................................328
DTC Confirmation Procedure ...............................329
Overall Function Check ........................................329
Diagnostic Procedure ...........................................330
Component Inspection ..........................................332
Removal and Installation ......................................333
DTC P1146 HO2S2 .................................................334
Component Description ........................................334
CONSULT-II Reference Value in Data Monitor Mode
.334
On Board Diagnosis Logic ....................................334
DTC Confirmation Procedure ...............................335
Overall Function Check ........................................336
Wiring Diagram .....................................................337
Diagnostic Procedure ...........................................338
Component Inspection ..........................................340
Removal and Installation ......................................341
DTC P1147 HO2S2 .................................................342
Component Description ........................................342
CONSULT-II Reference Value in Data Monitor Mode
.342
On Board Diagnosis Logic ....................................342
DTC Confirmation Procedure ...............................343
Overall Function Check ........................................344
Wiring Diagram .....................................................345
Diagnostic Procedure ...........................................346
Component Inspection ..........................................348
Removal and Installation ......................................349
DTC P1211 TCS CONTROL UNIT ..........................350
Description ............................................................350On Board Diagnosis Logic ....................................350
DTC Confirmation Procedure ................................350
Diagnostic Procedure ............................................350
DTC P1212 TCS COMMUNICATION LINE .............351
Description ............................................................351
On Board Diagnosis Logic ....................................351
DTC Confirmation Procedure ................................351
Diagnostic Procedure ............................................351
DTC P1217 ENGINE OVER TEMPERATURE ........352
System Description ...............................................352
CONSULT-II Reference Value in Data Monitor Mode
.353
On Board Diagnosis Logic ....................................353
Overall Function Check .........................................353
Wiring Diagram .....................................................356
Diagnostic Procedure ............................................359
Main 12 Causes of Overheating ...........................366
Component Inspection ..........................................367
DTC P1225 TP SENSOR ........................................368
Component Description ........................................368
On Board Diagnosis Logic ....................................368
DTC Confirmation Procedure ................................368
Diagnostic Procedure ............................................369
Removal and Installation .......................................369
DTC P1226 TP SENSOR ........................................370
Component Description ........................................370
On Board Diagnosis Logic ....................................370
DTC Confirmation Procedure ................................370
Diagnostic Procedure ............................................371
Removal and Installation .......................................371
DTC P1229 SENSOR POWER SUPPLY ................372
On Board Diagnosis Logic ....................................372
DTC Confirmation Procedure ................................372
Wiring Diagram .....................................................373
Diagnostic Procedure ............................................374
DTC P1564 ASCD STEERING SWITCH ................377
Component Description ........................................377
CONSULT-II Reference Value in Data Monitor Mode
.377
On Board Diagnosis Logic ....................................377
DTC Confirmation Procedure ................................378
Wiring Diagram .....................................................379
Diagnostic Procedure ............................................383
Component Inspection ..........................................386
DTC P1572 ASCD BRAKE SWITCH ......................387
Component Description ........................................387
CONSULT-II Reference Value in Data Monitor Mode
.387
On Board Diagnosis Logic ....................................387
DTC Confirmation Procedure ................................388
Wiring Diagram .....................................................389
Diagnostic Procedure ............................................390
Component Inspection ..........................................395
DTC P1574 ASCD VEHICLE SPEED SENSOR .....396
System Description ...............................................396
On Board Diagnosis Logic ....................................396
DTC Confirmation Procedure ................................396
Diagnostic Procedure ............................................397

EC-6 Wiring Diagram .....................................................515
Diagnostic Procedure ...........................................517
MI & DATA LINK CONNECTORS ...........................518
Wiring Diagram .....................................................518
EVAPORATIVE EMISSION SYSTEM .....................522
Description ............................................................522
Component Inspection ..........................................525
POSITIVE CRANKCASE VENTILATION ...............527
Description ............................................................527
Component Inspection ..........................................527
AUTOMATIC SPEED CONTROL DEVICE (ASCD) .529
System Description ...............................................529
Component Description ........................................530
SERVICE DATA AND SPECIFICATIONS (SDS) ....531
Fuel Pressure .......................................................531
Idle Speed and Ignition Timing .............................531
Calculated Load Value ..........................................531
Mass Air Flow Sensor ...........................................531
Intake Air Temperature Sensor .............................531
Engine Coolant Temperature Sensor ...................531
Heated Oxygen Sensor 1 Heater .........................531
Heated Oxygen sensor 2 Heater ..........................532
Crankshaft Position Sensor (POS) .......................532
Camshaft Position Sensor (PHASE) ....................532
Throttle Control Motor ...........................................532
Injector ..................................................................532
Fuel Pump ............................................................532
QR (WITHOUT EURO-OBD)
INDEX FOR DTC .....................................................533
Alphabetical Index ................................................533
DTC No. Index ......................................................535
PRECAUTIONS .......................................................537
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ...............................................................537
On Board Diagnostic (OBD) System of Engine ....537
Precaution ............................................................537
Wiring Diagrams and Trouble Diagnosis ..............540
PREPARATION .......................................................541
Special Service Tools ...........................................541
Commercial Service Tools ....................................542
ENGINE CONTROL SYSTEM ................................543
System Diagram ...................................................543
Vacuum Hose Drawing .........................................545
System Chart ........................................................547
Multiport Fuel Injection (MFI) System ...................548
Electronic Ignition (EI) System .............................550
Air Conditioning Cut Control .................................551
Fuel Cut Control (at No Load and High Engine
Speed) ..................................................................551
CAN Communication Unit .....................................552
BASIC SERVICE PROCEDURE .............................558
Idle Speed and Ignition Timing Check ..................558
Accelerator Pedal Released Position Learning ....559
Throttle Valve Closed Position Learning ...............560
Idle Air Volume Learning ......................................560
Fuel Pressure Check ............................................562ON BOARD DIAGNOSTIC (OBD) SYSTEM ...........565
Introduction ...........................................................565
Two Trip Detection Logic .......................................565
Emission-related Diagnostic Information ..............565
NATS (Nissan Anti-theft System) ..........................567
Malfunction Indicator (MI) .....................................568
TROUBLE DIAGNOSIS ..........................................572
Trouble Diagnosis Introduction .............................572
DTC Inspection Priority Chart ...............................576
Fail-Safe Chart ......................................................577
Basic Inspection ....................................................578
Symptom Matrix Chart ..........................................584
Engine Control Component Parts Location ...........588
Circuit Diagram .....................................................593
ECM Harness Connector Terminal Layout ............595
ECM Terminals and Reference Value ...................595
CONSULT-II Function (ENGINE) ..........................604
CONSULT-II Reference Value in Data Monitor Mode
.615
Major Sensor Reference Graph in Data Monitor
Mode .....................................................................618
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .620
Description ............................................................620
Testing Condition ..................................................620
Inspection Procedure ............................................620
Diagnostic Procedure ............................................621
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT .......................................................................624
Description ............................................................624
Diagnostic Procedure ............................................624
POWER SUPPLY AND GROUND CIRCUIT ...........625
Wiring Diagram .....................................................625
Diagnostic Procedure ............................................626
Component Inspection ..........................................632
Ground Inspection .................................................632
DTC U1000, U1001 CAN COMMUNICATION LINE .633
Description ............................................................633
On Board Diagnosis Logic ....................................633
DTC Confirmation Procedure ................................633
Wiring Diagram .....................................................634
Diagnostic Procedure ............................................635
DTC P0011 IVT CONTROL .....................................636
Description ............................................................636
CONSULT-II Reference Value in Data Monitor Mode
.637
On Board Diagnosis Logic ....................................637
DTC Confirmation Procedure ................................637
Overall Function Check .........................................639
Wiring Diagram .....................................................640
Diagnostic Procedure ............................................641
Component Inspection ..........................................643
Removal and Installation .......................................643
DTC P0102, P0103 MAF SENSOR .........................644
Component Description ........................................644
CONSULT-II Reference Value in Data Monitor Mode
.644
On Board Diagnosis Logic ....................................644
DTC Confirmation Procedure ................................644
Wiring Diagram .....................................................646

EC-8 Component Inspection ..........................................735
Removal and Installation ......................................736
DTC P1124, P1126 THROTTLE CONTROL MOTOR
RELAY .....................................................................737
Component Description ........................................737
CONSULT-II Reference Value in Data Monitor Mode
.737
On Board Diagnosis Logic ....................................737
DTC Confirmation Procedure ...............................737
Wiring Diagram .....................................................739
Diagnostic Procedure ...........................................742
Component Inspection ..........................................744
DTC P1128 THROTTLE CONTROL MOTOR .........745
Component Description ........................................745
On Board Diagnosis Logic ....................................745
DTC Confirmation Procedure ...............................745
Wiring Diagram .....................................................746
Diagnostic Procedure ...........................................750
Component Inspection ..........................................751
Removal and Installation ......................................752
DTC P1211 TCS CONTROL UNIT ..........................753
Description ............................................................753
On Board Diagnosis Logic ....................................753
DTC Confirmation Procedure ...............................753
Diagnostic Procedure ...........................................753
DTC P1212 TCS COMMUNICATION LINE ............754
Description ............................................................754
On Board Diagnosis Logic ....................................754
DTC Confirmation Procedure ...............................754
Diagnostic Procedure ...........................................754
DTC P1217 ENGINE OVER TEMPERATURE ........755
System Description ...............................................755
CONSULT-II Reference Value in Data Monitor Mode
.756
On Board Diagnosis Logic ....................................756
Overall Function Check ........................................756
Wiring Diagram .....................................................759
Diagnostic Procedure ...........................................762
Main 12 Causes of Overheating ...........................769
Component Inspection ..........................................770
DTC P1225 TP SENSOR ........................................771
Component Description ........................................771
On Board Diagnosis Logic ....................................771
DTC Confirmation Procedure ...............................771
Diagnostic Procedure ...........................................772
Removal and Installation ......................................772
DTC P1226 TP SENSOR ........................................773
Component Description ........................................773
On Board Diagnosis Logic ....................................773
DTC Confirmation Procedure ...............................773
Diagnostic Procedure ...........................................774
Removal and Installation ......................................774
DTC P1229 SENSOR POWER SUPPLY ................775
On Board Diagnosis Logic ....................................775
DTC Confirmation Procedure ...............................775
Wiring Diagram .....................................................776
Diagnostic Procedure ...........................................777
DTC P1564 ASCD STEERING SWITCH ................780
Component Description ........................................780CONSULT-II Reference Value in Data Monitor Mode
.780
On Board Diagnosis Logic ....................................780
DTC Confirmation Procedure ................................781
Wiring Diagram .....................................................782
Diagnostic Procedure ............................................786
Component Inspection ..........................................789
DTC P1572 ASCD BRAKE SWITCH ......................790
Component Description ........................................790
CONSULT-II Reference Value in Data Monitor Mode
.790
On Board Diagnosis Logic ....................................790
DTC Confirmation Procedure ................................791
Overall Function Check .........................................791
Wiring Diagram .....................................................793
Diagnostic Procedure ............................................794
Component Inspection ..........................................799
DTC P1574 ASCD VEHICLE SPEED SENSOR .....800
Component Description ........................................800
On Board Diagnosis Logic ....................................800
DTC Confirmation Procedure ................................800
Diagnostic Procedure ............................................801
DTC P1706 PNP SWITCH .......................................802
Component Description ........................................802
CONSULT-II Reference Value in Data Monitor Mode
.802
On Board Diagnosis Logic ....................................802
DTC Confirmation Procedure ................................802
Overall Function Check .........................................802
Wiring Diagram .....................................................804
Diagnostic Procedure ............................................805
DTC P1720 VSS ......................................................807
Description ............................................................807
CONSULT-II Reference Value in Data Monitor Mode
.807
On Board Diagnosis Logic ....................................807
DTC Confirmation Procedure ................................807
Diagnostic Procedure ............................................808
DTC P1805 BRAKE SWITCH .................................809
Description ............................................................809
CONSULT-II Reference Value in Data Monitor Mode
.809
On Board Diagnosis Logic ....................................809
DTC Confirmation Procedure ................................809
Wiring Diagram .....................................................811
Diagnostic Procedure ............................................812
Component Inspection ..........................................813
DTC P2122, P2123 APP SENSOR .........................815
Component Description ........................................815
CONSULT-II Reference Value in Data Monitor Mode
.815
On Board Diagnosis Logic ....................................815
DTC Confirmation Procedure ................................816
Wiring Diagram .....................................................817
Diagnostic Procedure ............................................819
Component Inspection ..........................................821
Removal and Installation .......................................821
DTC P2127, P2128 APP SENSOR .........................822
Component Description ........................................822