lights NISSAN X-TRAIL 2006 Owner's Guide

1. Clearance light
2. Headlight/Daytime running light
3. Front turn signal light/Front park light
4. Front fog light (if so equipped)
5. Map light/Room light
6. Side turn signal light
7. Driving light (if so equipped)
8. Front side marker light
9. Room light
10. Stop/tail light
11. Luggage room light
12. Rear turn signal light
13. High-mounted stop light
14. Back-up light
15. License plate light
16. Step light
17. Rear side marker light
SDI1933
LIGHTS8-26
Maintenance and do-it-yourself


06.4.14/T30-J/V5.0


HEADLIGHTS
ReplacingThe headlight is a semi-sealed beam type which
uses a replaceable headlight (halogen) bulb. A
bulb can be replaced from inside the engine
compartment without removing the headlight
assembly.
CAUTION

High pressure halogen gas is sealed
inside the halogen bulb. The bulb
may break if the glass envelope is
scratched or the bulb is dropped.

When handling the bulb, do not touch
the glass envelope.

Do not touch the bulb.

Use the same number and wattage as
originally installed:
Bulb no. (Wattage)
H4 (60/55W) - Halogen low/high-
beam

Do not leave the bulb out of theheadlight reflector for a long period
of time as dust, moisture, and smoke
may enter the headlight body and
affect the performance of the head
light.
1. Disconnect the battery negative cable.
2. Disconnect the electrical connector from the
rear end of the bulb.
3. Pull off the rubber cap
1.
4. Push and turn the retaining pin
2
to loosen
it.
5. Remove the headlight bulb. Do not shake or
rotate the bulb when removing it.
6. Install the new bulb in the reverse order of
removal.
SDI1946
Maintenance and do-it-yourself
8-27


06.4.14/T30-J/V5.0


HEADLIGHT AIMThe aim of the headlights may require adjust-
ment when replacing the headlight assembly or
when the vehicle’s front body has been repaired.
When the adjustment is required, follow these
procedures, or have them adjusted by a NISSAN
dealer.
Before performing the headlight aim adjustment:

Check the pressure of all tires for the correct
inflation pressure.

Check that the tools and spare tire are
stowed securely.
Check that the fuel and lubricants levels are
filled to correct capacities.

Unload all luggage and other items, which
may influence the vehicle’s height level.

Load a weight on the driver’s seat that is
equivalent to the weight of a driver.
Stopping the vehicle1. Park the vehicle on a level surface vertical to
the wall or screen to which the headlights will
be projected.
2. Move the vehicle close to the wall to deter-
mine the point P as shown in the illustration.The point P must be:
“H” is the distance between the headlight
center point to the level surface.
“W
L” is the distance between the left and
right headlight centers.
3. Mark point P on the wall or screen.
4. Back up the vehicle 5,000 mm (197.0 in,
16.4 ft) straight away from the wall or screen.
“L” is the distance between the wall or screen
to the vehicle’s front bumper.
5. Apply the parking brake.
SDI1664A
SDI1665
8-28
Maintenance and do-it-yourself


06.4.14/T30-J/V5.0


Be sure that the vehicle is parked directly vertical
to the wall on which the headlights will be
projected.Adjusting the headlight aim1. Turn on the headlight low beam.
2. Open the hood.
3. Turn the aiming adjustment screws
1
2,
located inside the engine compartment, until
the headlight projection, on the wall or
screen, does not move.
NOTE:
The aim adjustment screws are locatedon each side of the headlights. The
lower screw
1
is used to adjust the
horizontal aim. The upper screw
2
is
used to adjust the vertical aim.
The screws can be turned indefinitely in
each direction. Therefore be sure to ob-
serve the headlight projection move-
ment to determine the necessary turn-
ing amount.
4. Turn the lower screws
1
in the opposite
direction until the headlight projection be-
comes 70 mm (2.76 in) below the point P.
Once the left headlight has been adjusted,
perform right side adjustment as well.
“C” is the distance between point P and point
3.
5. Turn the upper screws
2
in the opposite
direction until the horizontal headlight projec-
tion’s turn point
3is directly below the point
P. Once the left headlight has been adjusted,
perform right side adjustment as well.
SDI1666A
Maintenance and do-it-yourself
8-29


06.4.14/T30-J/V5.0


EXTERIOR AND INTERIOR LIGHTS
Item Wattage (W) BulbNo.
Front turn signal light 21 T20
Front park light 5 T20
Side turn signal light 5 T10
Driving light (if so equipped)* 65 H1
Front side marker light 5 T10
Front fog light (if so equipped)* 55 H11
Rear combination light*
Turn signal 21 S25
Stop/Tail 21/5 T20
Back-up 21
License plate light 5 T10
High-mounted stop light 5
Room light 10
Map light 8
Luggage room light 10
Step light* 2.7 161
Rear side marker light 5 T10
*: See a NISSAN dealer for replacement.
SDI1685
8-30
Maintenance and do-it-yourself


06.4.14/T30-J/V5.0


Replacement proceduresAll other lights are either type A, B, C or D. When
replacing a bulb, first remove the lens and/or
cover.1: To remove the bulb
2: To install the bulb
SDI1311B
Front turn signal light
1
/Front clearance light
2
Maintenance and do-it-yourself
8-31


06.4.14/T30-J/V5.0


WHEELS AND TIRES
Road wheelType Size Offset mm (in)
Steel 16 x 6-1/2JJ 40 (1.57)
Aluminum16 x 6-1/2JJ 40 (1.57)
17 x 6-1/2JJ 40 (1.57)TireType Size Pressure (COLD)
ConventionalP215/65R16 220 kPa (32 psi)
P215/60R17 200 kPa (29 psi)
Spare Conventional —
DIMENSIONS AND WEIGHTSOverall length mm (in) 4,455 (175.4)
Overall width mm (in) 1,765 (69.5)
Overall heightmm (in) 1,675 (65.9)
mm (in) 1,750 (68.9)*
Front tread mm (in) 1,530 (60.2)
Rear tread mm (in) 1,530 (60.2)
Wheelbase mm (in) 2,625 (103.3)
Gross vehicle weight rating kg (lb)
See the C.M.V.S.S. certifica-
tion label on the driver’s side
lock pillar. Gross axle weight rating
Front kg (lb)
Rear kg (lb)
*: Rear air spoiler or roof rail with driving lights equipped model
9-8
Technical and consumer information


06.4.14/T30-J/V5.0


Class I hitchClass I trailer hitch equipment (receiver, ball
mount and hitch ball) can be used to tow trailers
of a maximum weight of 909 kg (2,000 lb).
You may add Class I trailer hitch equipment to
the vehicle that has a 909 kg (2,000 lb) maxi-
mum weight rating, but your vehicle is only
capable of towing the maximum trailer weights
shown in the Towing Load/Specification Chart
earlier in this section.
CAUTION

Special hitches which include frame
reinforcements are required for tow-
ing above 907 kg (2,000 lb). Suitable
genuine NISSAN hitches for pickup
trucks and sport utility vehicles are
available at a NISSAN dealer.

Do not use axle-mounted hitches.

The hitch should not be attached to
or affect the operation of the impact
absorbing bumper.

Do not modify the vehicle exhaust
system, brake system, etc. to install atrailer hitch.

After the hitch is removed, seal the
bolt holes to prevent exhaust fumes,
water or dust from entering the pas-
senger compartment.

Regularly check all trailer hitch
mounting bolts are securely
mounted.

To reduce the possibility of addi-
tional damage if your vehicle is
struck from the rear, where practical,
remove the hitch and/or receiver
when not in use.
Tire pressures
When towing a trailer, inflate the ve-
hicle tires to the recommended cold
tire pressure indicated on the Tire and
Loading Information label.

Trailer tire condition, size, load rating
and proper inflation pressure should
be in accordance with the trailer and
tire manufacturers’ specifications.
Safety chainAlways use a suitable chains between your
vehicle and the trailer. The safety chains should
be crossed and should be attached to the hitch,
not to the vehicle bumper or axle. Be sure to
leave enough slack in the chain to permit turning
corners.Trailer lights
CAUTION
When splicing into the vehicle electrical
system, a commercially available
power-type module/converter must be
used to provide power for all trailer
lighting. This unit uses the vehicle bat-
tery as a direct power source for all
trailer lights while using the vehicle tail
light, stoplight and turn signal circuits
as a signal source. The module/
converter must draw no more than 15
milliamps from the stop and tail lamp
circuits. Using a module/converter that
exceeds these power requirements may
damage the vehicle’s electrical system.
See a reputable trailer dealer to obtainTechnical and consumer information
9-19


06.4.14/T30-J/V5.0


the proper equipment and to have it
installed.
Trailer lights should comply with federal and/or
local regulations. For assistance in hooking up
trailer lights, contact a NISSAN dealer or repu-
table trailer dealer.Trailer brakesIf your trailer is equipped with a braking system,
make sure it conforms to federal and/or local
regulations and that it is properly installed.
WARNING
Never connect a trailer brake system
directly to the vehicle brake system.Pre-towing tips
Be certain your vehicle maintains a level
position when a loaded and/or unloaded
trailer is hitched. Do not drive the vehicle if it
has an abnormal nose-up or nose-down con-
dition; check for improper tongue load, over-
load, worn suspension or other possible
causes of either condition.
Always secure items in the trailer to prevent
load shifts while driving.

Load the trailer so approximately 60% of the
trailer load is in the front half and 40% is in
the back half.

Check your hitch, trailer tire pressure, vehicle
tire pressure, trailer light operation, and trailer
wheel lug nuts every time you attach a trailer
to the vehicle.

Be certain your rear view mirrors conform to
all federal, state or local regulations. If not,
install any mirrors required for towing before
driving the vehicle.
Trailer towing tipsIn order to gain skill and an understanding of the
vehicle’s behavior, you should practice turning,
stopping and backing up in an area which is free
from traffic. Steering stability, and braking per-
formance will be somewhat different than under
normal driving conditions.

Always secure items in the trailer to prevent
load shift while driving.

Avoid abrupt starts, acceleration or stops.

Avoid sharp turns or lane changes.

Always drive your vehicle at a moderate
speed. Some states or provinces have spe-cific speed limits for vehicles that are towing
trailers. Obey the local speed limits.

When backing up, hold the bottom of the
steering wheel with one hand. Move your
hand in the direction in which you want the
trailer to go. Make small corrections and back
up slowly. If possible, have someone guide
you when you are backing up.

Always block the wheels on both vehicle and
trailer when parking. Parking on a slope is not
recommended; however, if you must do so,
and if your vehicle is equipped with automatic
transmission, first block the wheels and apply
the parking brake, and then move the selector
lever into the P (Park) position. If you move
the selector lever to the P (Park) position
before blocking the wheels and applying the
parking brake, transmission damage could
occur.

When going down a hill, shift into a lower
gear and use the engine braking effect.
When going up a long grade, downshift the
transmission to a lower gear and reduce
speed to reduce chances of engine overload-
ing and/or overheating.

If the engine coolant rises to an extremely
high temperature when the air conditioning
system is on, turn off the air conditioner.
Coolant heat can be additionally vented by
9-20
Technical and consumer information


06.4.14/T30-J/V5.0


Fuses ............................................................................ 8-22
Fusible links ................................................................ 8-23
G
Gas cap ....................................................................... 3-10
Gauge ............................................................................. 2-3
Engine coolant temperature gauge .................. 2-5
Fuel gauge .............................................................. 2-6
Odometer ................................................................ 2-4
Speedometer .......................................................... 2-4
Tachometer ............................................................. 2-5
General maintenance .................................................. 8-2
Glove box .................................................................... 2-30
Glove box lock ........................................................... 2-30
H
Hazard warning flasher switch............................... 2-21
Head restraints ............................................................. 1-9
Headlights
Bulbreplacement ............................................... 8-27
Headlight switch ................................................. 2-18
Heated seats .............................................................. 2-22
Heater, Engine block heater ................................... 5-30
Hood release ................................................................ 3-7
Hook, Luggage hook ................................................ 2-33
Horn .............................................................................. 2-22
How to stop alarm, Vehicle security .................... 2-14
I
Ignition switch ............................................................... 5-6Automatic transmission models ............. 5-6, 5-10
Key positions .......................................................... 5-8
Manual transmission models .................. 5-7, 5-14
Immobilizer system .................................................... 2-14
In-cabin microfilter ......................................... 4-11, 4-13
Indicator lights............................................................ 2-10
Instrument brightness control ................................ 2-19
Instrument panel........................................................... 2-2
Interior light replacement......................................... 8-30
Interior lights ............................................................... 2-39
J
Jump starting................................................................. 6-7
K
Keyless entry (See remote keyless entry
system) ........................................................................... 3-5
Keys................................................................................. 3-2
L
Label, Air conditioner specification label ............ 9-11
Label, C.M.V.S.S. certification label ..................... 9-10
Label, Emission control information label............ 9-10
Labels
Air bag warning labels ...................................... 1-47
Engine serial number ......................................... 9-10
Vehicle identification number (VIN) .................. 9-9
LATCH (Lower Anchors and Tethers for
CHildren) system....................................................... 1-26Light
Air bag warning light ......................................... 1-47
Bulbreplacement ............................................... 8-26
Fog light switch................................................... 2-20
Headlight switch ................................................. 2-18
Headlights Bulbreplacement .......................... 8-27
Interior lights ........................................................ 2-39
Luggage room light ............................................ 2-41
Map light ............................................................... 2-41
Replacement ........................................................ 8-26
Warning/indicator lights and audible
reminders ..................................................... 2-7, 2-10
Lights, Exterior and interior light replacement ... 8-30
Loading information (See vehicle loading
information) ................................................................. 9-11
Lock
Back door lock....................................................... 3-7
Door locks ............................................................... 3-3
Glove box lock..................................................... 2-30
Luggage floor board ................................................. 2-32
Luggage hooks .......................................................... 2-33
Luggage room light................................................... 2-41
M
Maintenance
Battery ................................................................... 8-16
General maintenance ........................................... 8-2
Inside the vehicle................................................... 8-3
Maintenance information (display) .................... 4-3
Maintenance precautions .................................... 8-5
Maintenance requirements.................................. 8-2
Outside the vehicle............................................... 8-2
Seat belt maintenance ...................................... 1-19


06.4.14/T30-J/V5.0

10-3