parking brake NISSAN X-TRAIL 2013 Owner´s Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2013, Model line: X-TRAIL, Model: NISSAN X-TRAIL 2013Pages: 400, PDF Size: 8.75 MB
Page 262 of 400
> ( G L W 0 R G H O 7 $ @
5-6
Starting anddriving
from thetire pressure sensors,andthe
TPMS willnotfunction properly.
Some devices andtransmitters maytemporarily inter-
fere with theoperation ofthe TPMS andcause thelow
tire pressure warninglighttoilluminate. Someexam-
ples are:
. Facilities orelectric devices usingsimilar radio
frequencies arenear thevehicle.
. Ifatransmitter settosimilar frequencies isbeing
used inor near thevehicle.
. Ifa computer (orsimilar equipment) oraDC/AC
converter isbeing usedinor near thevehicle.
FCC Notice:
For USA:
This device complies withPart15ofthe FCC
Rules. Operation issubject tothe following two
conditions: (1)This device maynotcause harm-
ful interference, and(2)this device mustaccept
any interference received,including interference
that may cause undesired operation.
Note: Changes ormodifications notexpressly
approved bythe party responsible forcompli-
ance could voidtheuser's authority tooperate
the equipment.
For Canada:
This device complies withIndustry Canada
licence-exempt RSSstandard(s) .Operation is
subject tothe following twoconditions: (1)this
device maynotcause interference, and(2)this
device mustaccept anyinterference, including
interference thatmay cause undesired operation
of the device.
TPMS resetting
GUID-F7 6622F1-0B9 8-4141-BFE3 -22038209B548
T o keep theTPMS functioning properly,the reset
operation mustbeperformed inthe following cases.
. when thetirepressure isadjusted
. when atire orawheel isreplaced
. when thetires arerotated
Perform thefollowing procedures toreset theTPMS.
1. Park thevehicle inasafe andlevel place.
2. Apply theparking brakeandplace theshift lever in
the ªPº (Park) position.
3. Adjust thetire pressure onallfour tires tothe
recommended COLDtirepressure shownonthe
tire placard. Useatire pressure gaugetocheck
the tirepressure.
4. Place theignition switchinthe ªONº
position.
JVS0434X
Steering-wheel- mountedcontrols(leftside)
5. Use the
switch
*
1
until ªSettingsº appears,
and press ENTER
*
1
.
6. Use the
switch
*
1
until ªTire Pressuresº is
selected, andpress ENTER
*
1
.
7. Use the
switch
*
1
until ªCalibrateº is
selected, andpress ENTER
*
1
. 8.
Use the
switch
*
1
until ªStartº isselected,
and press ENTER
*
1
to reset theTPMS. When
the TPMS resetting starts,themessage ªTPMS
resettingº willbedisplayed.
9. After resetting theTPMS, drivethevehicle for
several minutes atspeeds above25km/h (16
MPH) .
If the low tirepressure warninglightilluminates after
the resetting operation, itmay indicate thattheTPMS
is not functioning properly.Have thesystem checked
by aNISSAN dealer.
For information regardingthelow tirepressure warning
light, seeªLow tirepressure warninglightº(P.2-14) .
DIESEL PARTICULA TEFILTER (DPF) (if
equipped)
GUID-5A9 CD1A0-AAA1 -48F8-8DC8-EB7CA86C2 ADF
WARNING:
. Becareful nottoburn yourself withexhaust
gases.
. Do not park thevehicle overflammable
materials suchasdry grass, wastepaperor
rags, asthey mayburn easily.
. Use thespecified engineoilfor Diesel
Particulate Filter(DPF) equipped models.
For details, seeªRecommended Fluids/lu-
bricants andcapacitiesº (P.9-2) .
CAUTION:
The DPF becomes extremely hotafter burning
particulate matter.
& R Q G L W L R Q
( [ F H S W I R U & K L Q D
Page 268 of 400
> ( G L W 0 R G H O 7 $ @
5-12
Starting anddriving
especially incold weather.
CAUTION:
Do not leave thevehicle unattended whilethe
engine iswarming up.
GUID-85BD 5A32-4CA0-4 B20-A3F7-7F2F8C6EA 88C
1. Apply theparking brake.
2. Continuously Variable Transmission (CVT)
model:
Move theshift lever tothe ªPº (Park) orthe ªNº
(Neutral) position.
The starter isdesigned tooperate onlywhen
the shift lever isin the proper position.
Manual Transmission (MT)model:
Move theshift lever tothe ªNº (Neutral) position.
The starter isdesigned tonot operate unless
the clutch pedalisfully depressed.
The Intelligent Keymust becarried when
operating theignition switch.
3. Place theignition switchinthe ªONº position.
Depress thebrake pedal(CVTmodel) orthe
clutch pedal(MTmodel) andpush theignition
switch tostart theengine.
For diesel engine models: Wait until theglow
indicator light
goes out.
T o start theengine immediately ,push andrelease
the ignition switchwhiledepressing thebrake
pedal orclutch pedalwiththeignition switchin
any position.
4. Immediately releasetheignition switchwhenthe
engine starts.Ifthe engine starts,butfails torun,
repeat theabove procedures.
If the engine isvery hard tostart inextremely cold
or hot weather, depresstheaccelerator pedaland
hold it.Push theignition switchforupto15
seconds whileholding. Release theaccelerator
pedal whentheengine starts.
CAUTION:
. Assoon asthe engine hasstarted, release
the ignition switchimmediately.
. Donot operate thestarter formore than15
seconds atatime. Ifthe engine doesnot
start, place theignition switchinthe ªOFFº
position andwait 10seconds beforecrank-
ing the engine again.Otherwise, thestarter
could bedamaged.
. Ifitbecomes necessary tostart theengine
with abooster batteryandjumper cables,
the instructions andcautions contained in
the ª6.Incase ofemergencyº sectionshould
be carefully followed.
5. Allow theengine toidle foratleast 30seconds
after starting theengine towarm-up. Driveat
moderate speedsforashort distance first,
especially incold weather.
CAUTION:
Do not leave thevehicle unattended whilethe
engine iswarming up.
6. To stop theengine, movetheshift lever tothe ªPº
(Park) position (CVTmodel) ormove theshift lever
to the ªNº (Neutral) position(MTmodel) ,apply the
parking brakeandplace theignition switchinthe
ªOFFº position.
ST ARTING ENGINE (modelwith
Intelligent Keysystem)
& R Q G L W L R Q
( [ F H S W I R U & K L Q D
Page 269 of 400
> ( G L W 0 R G H O 7 $ @
T32A1308 27-5DFB93F9 -CDD2-40A4-B4CA-7AD 7192119CB
DRIVING WITHCONTINUOUSL YVARI-
ABLE TRANSMISSION (CVT)
T32A1308 27-F7C5B DAC-B708- 41F7-9A32-F14C17BDCD AE
The Continuously Variable Transmission (CVT)inyour
vehicle iselectronically controlledtoproduce maximum
power andsmooth operation.
The recommended operatingprocedures forthis
transmission areshown onthe following pages.Follow
these procedures formaximum vehicleperformance
and driving enjoyment.
WARNING:
Do not downshift abruptlyonslippery roads.
This maycause aloss ofcontrol.
CAUTION:
. The cold engine idlespeed ishigh, souse
caution whenshifting thetransmission into
a forward orreverse position beforethe
engine haswarmed up.
. Avoid revving upthe engine whilethe
vehicle isstopped. Thiscould cause unex-
pected vehicle movement.
. Never shifttoeither theªPº (Park) orªRº
(Reverse) positionwhilethevehicle ismov-
ing. This could cause serious damage tothe
transmission.
. Start theengine ineither theªPº (Park) or
ªNº (Neutral) position.Theengine willnot
start inany other position. Ifitdoes, have
your vehicle checked byaNISSAN dealer.
. Except inan emergency, donot shift tothe
ªNº (Neutral) positionwhiledriving. Coast-
ing with thetransmission inthe ªNº (Neutral)
position maycause serious damage tothe transmission.
. Shift intotheªPº (Park) position andapply
the parking brakewhenatastandstill for
longer thanashort waiting period.
. Keep theengine atidling speed while
shifting fromtheªNº (Neutral) positionto
any driving position.
. When stopping thevehicle onanuphill
grade, donot hold thevehicle bydepressing
the accelerator pedal.Thefoot brake pedal
should bedepressed inthis situation.
Starting vehicle
T32A1308 27-E0E8CE2C -3F3F-496A-B326-0ED705AD3FCB
1. After starting theengine, fullydepress thefoot
brake pedalbefore moving theshift lever outofthe
ªPº (Park) position.
2. Keep thefoot brake pedaldepressed andmove
the shift lever toadriving position.
3. Release theparking brake,thefoot brake pedal,
and then gradually startthevehicle inmotion.
The CVT isdesigned sothe foot brake pedal
MUST bedepressed beforeshifting fromtheªPº
(Park) position toany driving position whilethe
ignition switchisin the ªONº position.
The shift lever cannot bemoved outofthe ªPº
(Park) position andinto anyofthe other
positions ifthe ignition switchisplaced inthe
ªLOCKº ,ªOFFº orªACCº position.
CAUTION:
. DEPRESS THEFOOTBRAKE PEDAL-Shift-
ing the shift lever toªDº ,ªDsº ,ªR º, ªL ºor
manual shiftmode without depressing the
foot brake pedalcauses thevehicle tomove
slowly whentheengine isrunning. Make sure
thefoot brake pedalisdepressed fully
and thevehicle isstopped beforeshifting
the shift lever.
. MAKE SUREOFTHE SHIFT LEVER POSI-
TION -Make suretheshift lever isin the
desired position. ªDº,ªDsº ,ªL ºand manual
shift mode areused tomove forward and
ªR ºto back up.
. WARM UPTHE ENGINE -Due tothe higher
idle speeds whentheengine iscold, extra
caution mustbeexercised whenshifting the
shift lever intothedriving position immedi-
ately afterstarting theengine.
Shifting
GUID-668 83E50-62D B-4D0A-AD 0D-64E18A8 E9465
JVS0391X
With manual shiftmode (LHDmodel) (Type A)
Starting anddriving
5-13
DRIVING
VEHICLE
& R Q G L W L R Q
( [ F H S W I R U & K L Q D
Page 270 of 400
> ( G L W 0 R G H O 7 $ @
5-14
Starting anddriving
JVS0441X
With manual shiftmode (LHDmodel) (Type B)
SSD0727
Without manualshiftmode (LHD model)
: Push
thebutton
*
A
while depressing the
foot brake
pedal.
: Push
thebutton
*
A
.
: Just
move theshift lever.
WARNING:
. Apply theparking brakeifthe shift lever isin
any position whiletheengine isnot running.
Failure todo socould cause thevehicle to
move unexpectedly orroll away andresult in
serious personal injuryorproperty damage. .
Ifthe shift lever cannot bemoved fromthe
ªPº (Park) position whiletheengine is
running andthefoot brake pedalisde-
pressed, thestop lights maynotwork.
Malfunctioning stoplights couldcause an
accident injuringyourself andothers.
After starting theengine, fullydepress thefoot brake
pedal, pushtheshift lever button andmove theshift
lever outofthe ªPº (Park) position.
If the ignition switchisplaced inthe ªOFFº orªACCº
position forany reason whiletheshift lever isin any
positions otherthantheªPº (Park) position, theignition
switch cannot beplaced inthe ªLOCKº position.
If the ignition switchcannot beplaced inthe ªLOCKº
position, performthefollowing steps:
1. Apply theparking brake.
2. Place theignition switchinthe ªONº position
while depressing thefoot brake pedal.
3. Move theshift lever tothe ªPº (Park) position.
4. Place theignition switchinthe ªLOCKº position.
P (Park) :
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Use thisposition whenthevehicle isparked orwhen
starting theengine. Makesurethatthevehicle is
completely stoppedandmove theshift lever into
the ªPº(Park) position. Applytheparking brake.
When parking onahill, first depress thefoot brake
pedal, applytheparking brake,andthen move theshift
lever intotheªPº (Park) position.
R (Reverse) :
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Use thisposition toback up.Make surethatthevehicle
is completely stoppedbeforeselecting theªRº
(Reverse) position. N
(Neutral) :
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Neither theforward norreverse gearisengaged. The
engine canbestarted inthis position. You may shift to
the ªNº (Neutral) positionandrestart astalled engine
while thevehicle ismoving.
D (Drive) :
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Use thisposition forallnormal forward driving.
Ds (Drive Sport) (ifequipped) :
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
When theshift lever isshifted fromtheªDº (Drive) to
ªDsº (Drive Sport) position, thetransmission entersthe
Ds (Drive Sport) mode.Moving theshift lever tothe
ªDsº (Drive Sport) position allowsyoutoenjoy ªsportyº
driving shiftoperation onawinding roadandfeel
smooth acceleration ordeceleration onahilly road by
moving inalower gearautomatically .Moving theshift
lever forwards andbackwards allowsmanual shifting.
When canceling theDs(Drive Sport) mode,returnthe
shift lever tothe ªDº (Drive) position. Thetransmission
returns tothe normal drivingmode.
L (Low) (ifequipped) :
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Use thisposition whenclimbing steephillsslowly or
driving slowlythrough deepsnow,sand ormud, orfor
maximum enginebraking onsteep downhill grades.
Manual shiftmode
T32A130 827-7DBE3 DA8-E793-455A-A5EF-C 0C301D4126A
When theshift lever isshifted fromtheªDº position to
the manual shiftgate withthevehicle stopped orwhile
driving, thetransmission entersthemanual shiftmode.
Shift ranges canbeselected manually.
In the manual shiftmode, theshift range isdisplayed
on the position indicator inthe meter.
Shift ranges upordown onebyone asfollows:
& R Q G L W L R Q
( [ F H S W I R U & K L Q D
Page 272 of 400
> ( G L W 0 R G H O 7 $ @
5-16
Starting anddriving
T ype A:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94A EAE0
JVS0392X
Example
1. Place theignition switchinthe ªOFFº orªLOCKº
position.
2. Apply theparking brake.
3. Remove theshift lockrelease cover(shown inthe
illustration above)usingasuitable tool.
4. Insert themechanical keyand push down theshift
lock release.
5. Press theshift lever button andmove theshift
lever tothe ªNº (Neutral) positionwhileholding
down theshift lockrelease. Replace theremoved
shift lockrelease coveraftertheoperation. T
ype B:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94A EAE0
JVS0466X
1. Place theignition switchinthe ªOFFº orªLOCKº
position.
2. Apply theparking brake.
3. Depress theshift lockrelease button.
4. Press theshift lever button andmove theshift
lever tothe ªNº (Neutral) positionwhileholding
down theshift lockrelease.
Place theignition switchinthe ªONº position to
release thesteering wheellock.
The vehicle maybemoved, bypushing, tothe desired
location.
If the shift lever cannot bemoved outofthe ªPº (Park)
position, haveaNISSAN dealerchecktheCVT system
as soon aspossible.
High fluidtemperature protectionmode
T32A1308 27-808BD 7D2-9BE0-4 70E-A660-24 B385D4FB8A
This transmission hasahigh fluidtemperature protec-
tion mode. Ifthe fluid temperature becomestoohigh
(for example, whenclimbing steepgrades inhigh
temperature withheavy loads),engine powerand,
under someconditions, vehiclespeedwillbede-
creased automatically toreduce thechance of
transmission damage.Vehicle speed canbecontrolled with
theaccelerator pedal,butengine andvehicle
speed maybelimited.
Fail-safe
T32A1308 27-5877C8 5B-EA11-4DD 6-9D52-6992317A74D 5
When thefail-safe operation occurs,theCVT willnot
be shifted tothe selected drivingposition.
If the vehicle isdriven underextreme conditions,
such asexcessive wheelspinning andsubse-
quent hardbraking, thefail-safe systemmaybe
activated. Thiswilloccur evenifall electrical
circuits arefunctioning properly.Inthis case,
turn theignition switchoffand wait for10
seconds. Thenplace theignition switchbackin
the ªONº position. Thevehicle shouldreturnto
its normal operating condition. Ifitdoes not
return toits normal operating condition, havea
NISSAN dealercheckthetransmission and
repair itifnecessary.
WARNING:
When thefail-safe operation occurs,vehicle
speed maybegradually reduced.Thereduced
speed maybelower thanother traffic,which
could increase thechance ofacollision. Be
especially carefulwhendriving. Ifnecessary, pull
to the side ofthe road atasafe place andallow
the transmission toreturn tonormal operation,
or have itrepaired ifnecessary.
& R Q G L W L R Q
( [ F H S W I R U & K L Q D
Page 273 of 400
> ( G L W 0 R G H O 7 $ @
DRIVING WITHMANUAL TRANSMISSION
(MT)
T32A1308 27-F9C2D0 EE-1C88-43FA-80B1 -BC9035D4 5F56
WARNING:
. Donot downshift abruptlyonslippery roads.
This maycause aloss ofvehicle control.
. Donot over-rev theengine whenshifting to
a lower gear.Thismay cause aloss of
vehicle control orengine damage.
CAUTION:
. Donot rest your footonthe clutch pedal
while driving. Thismay damage theclutch
system.
. Fully depress theclutch pedalbefore shift-
ing tohelp prevent transmission damage.
. Stop thevehicle completely beforeshifting
into theªRº(Reverse) position.
. When thevehicle isstopped foraperiod of
time, forexample waitingatstoplights, shift
to the ªNº (Neutral) positionandrelease the
clutch pedalwiththefoot brake pedal
depressed.
. Do not shift tothe ªNº (Neutral) position
while driving. Coasting withthetransmis-
sion inthe ªNº (Neutral) positionmaycause
serious damage tothe transmission.
Starting vehicle
T32A130827- 79841C26-BFA7-47DD-85A1- 81CD1AE3CABD
1. After starting theengine, depress theclutch pedal
to the floor andmove theshift lever tothe ª1º(1st)
or ªRº (Reverse) position.
2. Slowly depress theaccelerator pedal,releasing
the clutch pedalandparking brakeatthe same
time.
Shifting gear
T32A1308 27-BA6FF761 -6916-4D57-ADC5-14 9CCFDB8A1 0
T o change gears,orwhen upshifting ordownshifting,
fully depress theclutch pedal, shiftintotheappropriate
gear, thenslowly andsmoothly releasetheclutch
pedal.
T o ensure smooth gearchanges, fullydepress the
clutch pedalbefore operating theshift lever. Ifthe
clutch pedalisnot fully depressed beforethe
transmission isshifted, agear noise maybeheard.
T ransmission damagecouldoccur.
Start thevehicle inthe ª1º(1st) position andshift to
the ª2º(2nd) ,ª3º (3rd) ,ª4º (4th) ,ª5º (5th) andª6º
(6th) gearinsequence according tothe vehicle speed.
If itis difficult tomove theshift lever intotheªRº
(Reverse) orª1º (1st) position, shifttothe ªNº (Neutral)
position, andthen release theclutch pedalonce.Fully
depress theclutch pedalagainandshift intoªRºorª1º
.
SSD0552
. To back up,stop thevehicle andmove theshift
lever intotheªNº (Neutral) position,andthen pull
the ring
*
1
upward toshift intotheªRº (Reverse)
position.
. The pullring returns toits original position when
the shift lever ismoved tothe ªNº (Neutral)
position.
Suggested maximumspeedineach gear
T32A1308 27-751BC2 BE-4FBE-40E4-87B2-7F6A039719B A
Downshift toalower gearifthe engine isnot running
smoothly ,or ifyou need toaccelerate.
Do not exceed themaximum suggested speed(shown
below) inany gear. Forlevel road driving, usethe
highest gearsuggested forthat speed. Always observe
posted speedlimits,anddrive according tothe road
conditions whichwillensure safeoperation. Donot
over-rev theengine whenshifting toalower gearasit
may cause engine damage orloss ofvehicle control.
MR20DD enginemodel:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
km/h (MPH)
1st 45
(28)
2nd 79
(49)
3rd 110
(68)
4th 143
(89)
5th &6th Ð
(Ð)
Starting anddriving
5-17
& R Q G L W L R Q
( [ F H S W I R U & K L Q D
Page 282 of 400
> ( G L W 0 R G H O 7 $ @
5-26
Starting anddriving
. Always usetires ofthe same type,size,brand,
construction (bias,bias-belted orradial) ,and
tread pattern onallfour wheels. Installtirechains
on the front wheels whendriving onslippery roads
and drive carefully .
. Besure tocheck thebrakes immediately after
driving inmud orwater. (SeeªBrake systemº (P.5-
57) .)
. Whenever youdrive off-road throughsand,mudor
water asdeep asthe wheel hub,more frequent
maintenance mayberequired. Fordetails, referto
ªMaintenance foroff-road drivingºinaseparate
maintenance booklet.
. Avoid parking yourvehicle onsteep hills.Ifyou get
out ofthe vehicle anditrolls forward, backward or
sideways, youcould beinjured.
TIRES OF4WD MODEL
T32A130 827-AE5C0 353-CEE0-4F0C-8B42-DD14B0 A90107
CAUTION:
. Always usetires ofthe same size,brand,
construction (bias,bias-belted orradial) ,
and tread pattern onallfour wheels. Failure
to do somay result inacircumference
difference betweentiresonthe front and
rear axles which willcause excessive tire
wear andmay damage thetransmission,
transfer caseandrear differential gears.
. Only usespare tiresspecified foreach 4WD
model.
If excessive tirewear isfound, itis recommended that
all four tires bereplaced withtires ofthe same size,
brand, construction andtread pattern. Thetire
pressure andwheel alignment shouldalsobechecked
and corrected asnecessary .Contact aNISSAN
dealer.
Snow tires
T32A1308 27-786C9A7 D-5F2C-4C44-8252-7577B2315AD6
If you install snowtires,theymust alsobethe same
size, brand, construction andtread pattern onallfour
wheels.
Tire inflation pressure
T32A130827-0 2F5E13F-EB84-4678-B8E3-01C847020459
Check thepressures inall tires, including thespare,
with agauge periodically whenataservice station.
Adjust tothe specified pressureifnecessary .Tire
pressures areshown onthe tire placard.
Tire rotation
T32A130 827-BCA9A BF3-4A1A-42 5E-8276-807FAAD0A08E
NISSAN recommends thattires berotated every5,000
km (3,000 miles).Do not include thespare tireinthe
tire rotation.
Tire chain
T32A130 827-61205 7E2-0991-4 824-9088-F4 4BB593B9BC
Tire chains mustbeinstalled onlyonthe front
wheels andnotonthe rear wheels.
Do not drive withtirechains onpaved roadswhich are
clear ofsnow .Driving withchains insuch conditions
can cause damage tothe various mechanisms ofthe
vehicle duetosome overstress.
GUID-282 AEC18-44 35-4758-87 F0-FE282A2B8D35
Except forEurope: Vehicle Dynamic Control
(VDC) system
For Europe: Electronic StabilityProgram (ESP)
system
WARNING:
. The VDC/ESP systemisdesigned tohelp the
driver maintain stabilitybutdoes notpre-
vent accidents duetoabrupt steering opera-
tion athigh speeds orby careless or
dangerous drivingtechniques. Reducevehi-
cle speed andbeespecially carefulwhen
driving andcornering onslippery surfaces
and always drivecarefully.
. Donot modify thevehicle's suspension. If
suspension partssuchasshock absorbers,
struts, springs, stabilizer bars,bushings and
wheels arenot NISSAN recommended for
your vehicle orare extremely deteriorated,
the VDC/ESP systemmaynotoperate
properly. Thiscould adversely affectvehicle
handling performance, andtheVDC/ESP
warning light
may illuminate.
. Ifbrake related partssuchasbrake pads,
rotors andcalipers arenot NISSAN recom-
mended orare extremely deteriorated, the
VDC/ESP systemmaynotoperate properly
and theVDC/ESP warninglight
may
illuminate.
. Ifengine control related partsarenot
NISSAN recommended orare extremely
deteriorated, theVDC/ESP warninglight
may illuminate.
. When driving onextremely inclinedsurfaces
such ashigher banked corners, theVDC/
ESP system maynotoperate properly and
VEHICLE DYNAMIC CONTROL
(VDC)/ELECTR ONICSTABILITY
PROGRAM (ESP)SY STEM
& R Q G L W L R Q
( [ F H S W I R U & K L Q D
Page 304 of 400
> ( G L W 0 R G H O 7 $ @
5-48
Starting anddriving
ECO DRIVE REPORT
GUID-50E2 3061-A0D4-48FA-B1AB-3D 81CC65E BC0
JVI0929X
When theignition switchisin the OFF position, ECO
management displayappears.
*
1
ECO evaluation
*
2
Previous 5times (History)
*
3
Current fueleconomy
*
4
Best fueleconomy
The result ofECO evaluation isdisplayed whenthe
vehicle isdriven forabout 10minutes ormore.
*
1
: The more economically youdrive, the more
appear.
*
2
: The average fueleconomy forthe previous 5
times willbedisplayed.
*
3
: The average fueleconomy sincethelast reset will
be displayed.
*
4
: The best fueleconomy ofthe past history willbe
displayed.
GUID-4EA3AC 09-F236-4911-80A7-FA5BD8B3C 037
WARNING:
. Do not stop orpark thevehicle over
flammable materialssuchasdry grass,
waste paperorrags. Theymayignite and
cause afire.
. Safe parking procedures requirethatboth
the parking brakebeapplied andtheshift
lever placed inthe ªPº(Park) position
(Continuously Variable Transmission model)
or the shift lever placed inan appropriate
gear (Manual Transmission model).Failure
to do socould cause thevehicle tomove
unexpectedly orroll away andresult inan
accident.
. When parking thevehicle, makesurethe
shift lever ismoved tothe ªPº(Park)
position. Theshift lever cannot bemoved
out ofthe ªPº(Park) position without
depressing thefoot brake pedal(Continu-
ously Variable Transmission model).
. Never leavetheengine running whilethe
vehicle isunattended.
. When parking foranextended periodoftime
with Stop/Start SystemorIdling StopSys-
tem (ifequipped) activated,theengine will
restart automatically. Neverleavethevehi-
cle with theignition switchinthe ªONº
position.
. Never leavechildren oradults whowould
normally requirethesupport ofothers alone
in the vehicle. Petsshould notbeleft alone
either. Theycould unknowingly activate
switches orcontrols andinadvertently be-
come involved inaserious accident and
injure themselves. Onhot, sunny days, temperatures
inaclosed vehicle could
quickly become highenough tocause se-
vere orpossibly fatalillness topeople and
animals.
P ARKING
& R Q G L W L R Q
( [ F H S W I R U & K L Q D
Page 305 of 400
> ( G L W 0 R G H O 7 $ @
SSD0488
Left-Hand Drive(LHD) model
SSD0489
Right-Hand Drive(RHD) model
1. Firmly applytheparking brake.
2. Continuously Variable Transmission (CVT)model:
Move theshift lever tothe ªPº (Park) position.
Manual Transmission (MT)model: Movetheshift
lever tothe ªRº (Reverse) position.Whenparking
on anuphill grade, movetheshift lever tothe ª1º
(1st) position.
3. To help prevent thevehicle frommoving intotraffic
when parked onanincline, itis agood practice to
turn thewheels asillustrated.
HEADED DOWNHILL WITHCURB
*
1
T urn thewheels towards thecurb andmove the vehicle
forward untilthecurb sidewheel gently
touches thecurb. Thenapply theparking brake.
HEADED UPHILLWITHCURB
*
2
T urn thewheels awayfromthecurb andallow the
vehicle tomove backuntilthecurb sidewheel
gently touches thecurb. Thenapply theparking
brake.
HEADED UPHILLORDOWNHILL, WITHOUT
CURB
*
3
T urn thewheels towardtheside ofthe road sothe
vehicle willmove awayfromthecenter ofthe road
if the vehicle moves. Thenapply theparking brake. 4.
Model withIntelligent Key:
Place theignition switchinthe ªOFFº position.
Model without Intelligent Key:
Place theignition switchinthe ªLOCKº position
and remove thekey.
NO TE:
For Model withStop/Start SystemorIdling Stop
System:
Use thissystem whenthevehicle isstopped for
a period oftime, forexample waitingatstop-
lights.
Stop theengine withtheignition switchwhen
parking, etc.for anextended periodoftime.
Starting anddriving
5-49
& R Q G L W L R Q
( [ F H S W I R U & K L Q D
Page 306 of 400
> ( G L W 0 R G H O 7 $ @
5-50
Starting anddriving
GUID-B933B 47B-826E-4EDF-9FFF-A 382A0D7D 08E
SSD0723
T ype A
JVS0437X
T ype B
The parking sensor(sonar) systemsounds atone to
inform thedriver ofobstacles nearthebumper.
When theªDisplayº keyisON, thesensor viewwill
automatically appearinthe vehicle information display.
WARNING:
. The parking sensor(sonar) systemisa
convenience butitis not asubstitute for
proper parking. Thedriver isalways respon-
sible forsafety during parking andother
manoeuvres. Alwayslookaround andcheck
that itis safe todo sobefore parking. .
Read andunderstand thelimitations ofthe
parking sensor(sonar) system ascontained
in this section. Thecolors ofthe corner
sensor indicator andthedistance guidelines
in the front (ifequipped)/rear viewindicate
different distances tothe object. Inclement
weather orultrasonic sourcessuchasan
automatic carwash, atruck's compressed-
air brakes orapneumatic drillmay affect the
function ofthe system; thismay include
reduced performance orafalse activation. .
This function isdesigned asan aid tothe
driver indetecting largestationary objectsto
help avoid damaging thevehicle. Thesystem
is not designed toprevent contactwithsmall
or moving objects. Alwaysmoveslowly.
. The system willnotdetect smallobjects
below thebumper, andmay notdetect
objects closetothe bumper oron the
ground.
. The system maynotdetect thefollowing
objects.
Ð Fluffy objects suchassnow, cloth,
cotton, glass-wool, etc.
Ð Thin objects suchasrope, wireand
chain, etc.
Ð Wedge-shaped objects
. Ifyour vehicle sustains damagetothe
bumper fascia,leaving itmisaligned orbent,
the sensing zonemaybealtered causing
inaccurate measurement ofobstacles or
false alarms.
CAUTION:
. Keep theinterior ofthe vehicle asquiet as
possible tohear thetone clearly.
. Keep thesensors (located onthe bumper
fascia) freefrom snow, iceand large accu-
mulations ofdirt. Donot clean thesensors
with sharp objects. Ifthe sensors are
covered, theaccuracy ofthe sensor function
will bediminished.
P ARKING SENSOR (sonar)SY STEM
(if equipped)
& R Q G L W L R Q
( [ F H S W I R U & K L Q D