ABS OLDSMOBILE AURORA 1995 Owners Manual

Avoid needless heavy braking. Some people drive in
spurts -- heavy acceleration followed by heavy braking
-- rather than keeping pace with traffic. This is a
mistake. Your brakes may not have time to cool between
hard stops. Your brakes will wear
out much fdster if you
do a lot of heavy braking. If you keep pace with the
traffic and allow realistic following distances, you will
eliminate a lot
of unnecessary braking. That means
better braking and longer brake life.
If your engine ever stops while you’re driving, brake
normally but don’t pump your brakes.
If you do, the
pedal may get harder to push down. If your engine
stops, you will still have some power brake assist.
But
you will use it when you brake. Once the power assist is
used up,
it may take longer to stop and the brake pedal
will be harder to push.
Anti-Lock Brakes (ABS)
Your Aurora has an advanced electronic braking system
that
will help prevent a braking skid.
ANT’- (I)
LOCK
This light on the
instrument panel
will
come on briefly when
you start your vehicle.
When you start your vehicle and begin to drive away,
you may hear a momentary motor or clicking noise. And
you may even notice that your brake pedal moves
a little
while this is going on. This is the ABS system testing
itself.
If there’s a problem with the anti-lock brake
system, the anti-lock brake system warning light will
stay
on.
See “Anti-Lock Brake System Warning Light“ in the
Index.
4-6
ProCarManuals.com

I
I
Here’s how anti-lock works. Let’s say the road is wet.
You’re driving safely. Suddenly an animal jumps out in
front
of you.
You slam on the brakes. Here’s what happens with ABS.
A computer senses that wheels are slowing down. If one
of the wheels is about to stop rolling, the computer will
separately work the brakes at each front wheel and at the
rear wheels. The
anti-lock system can change the brake pressure
faster than any driver could. The computer
is
programmed to make the most of available tire and road
conditions.
You can steer around the obstacle while braking hard.
As you brake, your computer keeps receiving updates on
wheel speed and controls braking pressure accordingly.
4-7
ProCarManuals.com

If your traction control system is off, then an
acceleration skid is also best handled by easing your
foot
off the accelerator pedal.
If your vehicle starts to slide, ease your foot
off the
accelerator pedal and quickly steer the way you want the
vehicle to
go. If yo11 start steering quickly enough, your
vehicle may straighten out. Always be ready for a
second skid
if it occurs.
Of course, traction is reduced when water, snow, ice,
gravel, or other material is on the road. For safety, you’ll
want to
slow down and adjust your driving to these
conditions.
It is important to slow down on slippery
surfices because stopping distance
will be longer and
vehicle control more limited.
While driving
on a surface with reduced traction, try
your best to avoid sudden steering, acceleration, or
braking (including engine braking by shifting
to a lower
gear). Any sudden changes could cause the tires
to slide.
You may not realize the surface is slippery
until your
vehicle is skidding. Learn to recognize warning clues
--
such as enough water, ice or packed snow on the road to
make a “mirrored surface”
-- and slow down when you
have any doubt.
Remember:
Any anti-lock brake system (ABS) helps
avoid only the braking skid.
Driving at Night
m
Night driving is more dangerous than day driving. One
reason is that some drivers are likely to be impaired
--
by alcohol or drugs, with night vision problems, or by
fatigue.
4-14
ProCarManuals.com

Parking on Hills
You really should not park your vehicle, with a trailer
attached,
on a hill. If something goes wrong, your rig
could start
to move. People can be injured, and both
your vehicle and
the trailer can be damaged.
But if you ever have to park your rig on a hill, here‘s
how to do it:
1.
2.
3.
4.
5.
Apply your regular brakes, but don’t shift into
PARK (P) yet.
Have someone place chocks under the trailer wheels.
When the wheel chocks are in place, release the
regular brakes
until the chocks absorb the load.
Reapply the regular brakes. Then apply your parking
brake, and
then shift to PARK (P).
Release the regular brakes.
When You Are Ready to Leave After
Parking on a Hill
I. Apply your regular brakes and hold the pedal down
while you:
Start your engine:
Shift into a gear; and
Release the parking brake.
2. Let LIP on the brake pedal.
3. Drive slowly until the trailer is clear of the chocks.
4. Stop and have someone pick up and store the chocks.
Maintenance When Trailer Towing
Your vehicle will need service more often when you’re
pulling
a trailer. See the Maintenance Schedule for more
on this. Things that are especially important
in trailer
operation are automatic transaxle fluid (don’t overfill),
engine oil, belt, cooling system, and brake adjustment.
Each of these
is covered in this manual, and ;he Index will
help you find them quickly. If you’re trailering, it‘s a good
idea to review these sections before you stat your trip.
Check periodically
to see that all hitch nuts and bolts
are tight.
4-36
ProCarManuals.com

4. There's a temperature sensor on the corner of the air
cleaner cover. Use
a screwdriver to release the
sensor's electrical connector retainer, and
pull up.
5. Unsnap the two clamps by pushing down on the top
of the air cleaner cover and pushing in on the clamps
toward the center
of the cover. Then remove the
cover.
A. Remove the air filter.
7. Install the new air filter and reverse all steps to
reinstall the cover. electrical wires, duct and clamp.
Be sure the
tabs of the air cleaner cover fit into the
slots
of the air cleaner housing. Then make sure both
clamps are
f~~lly engaged.
6- 15
ProCarManuals.com

4. Check to make sure the safety belts are properly
routed and that
no portion of any safety belt is
trapped under
the seat. Also make sure the seat
cushion
is secured.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by
a combination of fuses and circuit
breakers. This greatly reduces the chance
of damage
caused by electrical problems.
There are three main fuse panels.
Two are located under
the rear seat.
To access these panels, you’ll need to
remove the seat. See the previous description under
“Removing
the Rear Seat Cushion” to see how. This
procedure
is somewhat difficult. You may wish to have
your retailer replace the fuse, instead.
V
Once the seat is removed,
you’ll find two fuse panels
on the driver’s side of the
battery. Each
is protected by
a plastic box with four tabs.
Pull up on all four tabs at
the same time to loosen
them and pull off the box.
Of these two panels, the cover on the passenger-side
fuse panel
has an extra plastic cap attachment. You’ll
need to slide this out of the grooves which hold it there
before removing the rest
of the box.
To replace the covers, line the four tabs up and simply
snap
them back into place. The extra plastic cap
attachment slides back into place.
6-54
ProCarManuals.com