height OLDSMOBILE AURORA 1995 Owners Manual

Installing a Garage Door Opener
To install a garage door opener in the overhead console,
follow these directions:
1. Push the extended tab, which is located in front of
the
GARAGE button, and pull the door downward.
2. Remove the square height adapters from the door.
3. Refer to the chart on the following pages to
determine the number and location
of the height
adapters for your transmitter unit.
If your unit does
not appear on the chart, you will have
to try random
adapter number and location combinations.
2-44
ProCarManuals.com

4
3
2
1
Ill
567 I
4. Place the height adapters on the proper peg. The
height adapters can be stacked on each other
as
needed.
5. Line up the transmitter button with the height
6. Remove the Velcro@ square from the inside of the
overhead console. Peel off the backing from the
Velcro and attach
it to the transmitter unit, providing
good alignment with
the mating Velcro pad which
remains
in the console.
adapters
to ensure correct alignment.
7. Attach the transmitter unit to the inside of the
console
by means of the Velcro.
8. Close the door. Test the unit by pressing the
GARAGE button.
If the unit does not work, try
different pin and hole combinations.
Your Garage Door Transmitter Vehicle Console Door
Adapters Adapters
Button Model
Name Number
Of Position For
CHAMBERLAIN
4 5 1 G-3684
CRUSADER
3 9 1 1 -BUTTON
GENIE
3 3 1 AT85 P
GENIE 4
5 1 AT90 GENIE
4 5 1 AT85
I GENIE I MAT85 I 1 I 6 14 I
I GENIE I AT285P I 1 I 10 I 3 I
I I 2 I 1 I 3 I
I GENIE I AT95 1 I 10 I 3 1
2 I 3 I 3 I
I I 13 I 1 I 3 I
LIFTMASTER
3 2 1 G3456
LIFTMASTER
3 2 1 G3446
ProCarManuals.com

Brake Wear
Your Aurora has four-wheel disc brakes.
Disc brake pads have built-in wear indicators that make
a high-pitched warning sound when the brake pads are
worn and new pads are needed. The sound may come
and
go or be heard all the time your vehicle is moving
(except when
you are pushing on the brake pedal
firmly).
I NOTICE:
Continuing to drive with worn-out brake pads
could result in costly brake repair.
Some driving conditions or climates may cause a brake
squeal when the brakes are first applied or lightly
applied. This does not mean something is wrong
with
your brakes.
Brake linings should always
be replaced as complete
axle sets.
Brake Pedal Travel
See your retailer if the brake pedal does not return to
normal height, or
if there is a rapid increase in pedal
travel. This could be
a sign of brake trouble.
Brake Adjustment
Every time YOLI apply the brakes, with or without the
vehicle moving, your brakes adjust for wear.
6-25
ProCarManuals.com

Wheel Replacement
Replace any wheel that is bent, cracked, or badly rusted
or corroded. If wheel nuts keep coming loose, the wheel,
wheel bolts, and wheel nuts should be replaced.
If the
wheel leaks air, replace it (except some aluminum
wheels, which can sometimes
be repaired). See your
Aurora retailer if any
of these conditions exist.
Your retailer will know the kind
of wheel you need.
Each new wheel should have the same load carrying
capacity, diameter, width, offset, and be mounted the
same way as the one it replaces.
If you need
to replace any of your wheels, wheel bolts,
or wheel nuts, replace them only with new
GM original
equipment parts. This way, you will be sure to have the
right wheel, wheel bolts, and wheel nuts for your Aurora
model.
I NOTICE:
The wrong wheel can also cause problems with
bearing life, brake cooling,
speedometer/odometer calibration, headlamp aim, bumper height, vehicle ground clearance,
and tire
or tire chain clearance to the body and
chassis.
6-41
ProCarManuals.com