start stop button OLDSMOBILE AURORA 1996 Owners Manual

and also release the shift lever button on floor shift
console models as you maintain brake application. Then
move the shift lever into the gear you wish. (Press the shift lever button before moving the
shift lever on floor
shift console models.) See “Shifting Out
of PARK (P)”
in this section.
REVERSE (R): Use this gear to back
up.
NOTICE:
Shifting to REVERSE (R) while your vehicle is
moving forward could damage your transaxle.
Shift to REVERSE (R) only after your vehicle
is stopped.
To rock your vehicle back and forth to get out of snow,
ice or sand without damaging your transaxle, see
“If
You’re Stuck: In Sand, Mud, Ice or Snow” in the Index. NEUTRAL
(N): In this position, your
engine
doesn’t connect with the wheels.
To restart when you’re
already moving, use NEUTRAL (N) only. Also, use
NEUTRAL
(N) when your vehicle is being towed.
Shifting out of PARK
(P) or NEUTRAL (N) while
your engine is “racing” (running
at high speed)
is dangerous. Unless your foot
is firmly on the
brake pedal, your vehicle could move very
rapidly.
You could lose control and hit people or
objects. Don’t shift out
of PARK (P) or
NEUTRAL (N) while your engine is racing.
I NOTICE:
Damage to your transaxle caused by shifting out
of PARK
(P) or NEUTRAL (N) with the engine
racing isn’t covered by your warranty.
2-24
~ ..
ProCarManuals.com

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)
Ths device may not cause harmful interference,
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
Programming the Transmitter
Do not use the universal transmitter with any garage
door opener that does not have the “stop and reverse’’
safety feature. This includes any garage door opener
model manufactured before April
1, 1982.
Be sure that people and objects are clear of the garage
door you are programming!
Your vehicle’s engine should be turned off while
programming your transmitter. Follow these steps to
program up to three channels:
1. If you have not previously programmed a universal
transmitter channel, proceed to Step
2. Otherwise,
hold down the two outside buttons on the uniyersal
transmitter until the red light begins
to flash rapidly
(approximately 20 seconds). Then release the
buttons. This procedure initializes the memory and
erases any previous settings for all three channels. 2. Hold the end of your hand-held transmitter against
the bottom surface of the universal transmitter
so
that you can still see the red light.
3. Decide which one of the three channels you want to
program. Using both hands, press the hand-held
transmitter button and the desired button on the
universal transmitter. Continue to hold both buttons
through Step
4.
4. Hold down both buttons until you see the red light
on the universal transmitter flash rapidly. The rapid
flashing, which could take up to
90 seconds,
indicates that the universal transmitter has been
programmed. Release both buttons once the light
starts to flash rapidly.
If you have trouble programming the universal
transmitter, make sure that you have followed the
directions exactly as described and that the batteries in
the hand-held transmitter are not dead. If you still
cannot program it, rotate your hand-held transmitter end
over end and try again. The universal transmitter may
not work with older garage door openers that do not
meet current Federal Consumer Safety Standards.
If you
cannot program the transmitter after repeated attempts,
consult your Aurora retailer.
ProCarManuals.com

While the tape is playing, use the VOL, FADE, BAL,
TREB and BASS controls just as you do for the radio.
The display will show TP with a box around
it and an
arrow to show which side
of the tape is playing.
Your tape bias is set automatically. When a metal or
chrome tape is inserted,
HI-BIAS appears on the
display.
If you want to insert a tape when the ignition is
off, first press EJECT or RCL.
If E and a number appear on the radio display, the tape
won’t play because
of an error.
0 E10: The tape is tight and the player can’t turn the
tape hubs. Remove the tape. Hold the tape with the
open end down and try to turn the right hub
counterclockwise with a pencil. Turn the tape over
and repeat. If the hubs do not turn easily, your tape
may be damaged and should not be used in thecd
..
player. Try a new tape to make sure your player is
working properly.
0 Ell: The tape is broken. Try a new tape.
If any error occurs repeatedly or if an error can’t be
corrected, please contact your retailer.
If your radio
displays an error number, write
it down and provide it to
your retailer when reporting the problem.
REV (1): Press this button to reverse the tape rapidly.
Press it again to return
to playing speed. The radio will
play the last-selected station while the tape reverses.
You may select stations during REV operation by
using TUNE.
FWD (2): Press this button to advance quickly to
another part of the tape. Press the button again to return
to playing speed. The radio will play the last-selected
station while the tape advances. You may select stations
during FWD operation by using
TUNE.
PROG (3): Press this button to play the other side
of the tape.
NR (4): Press this button to reduce background noise.
Note that the double-D symbol will appear on the display.
Dolby@ Noise Reduction is manufactured under a
license from Dolby Laboratories Licensing Corporation.
Dolby and the double-D symbol are trademarks of
Dolby Laboratories Licensing Corporation.
SEEK: Press the up or down arrow to search for the next
or previous selection on the tape.
To go to the start of the
last selection played, press the down arrow again as
it
stops at the start of a selection. The radio will not play
while seeking. Your tape must have at least three seconds
of silence between each selection for SEEK to work.
- -3
ProCarManuals.com

All of the CD functions are controlled by the radio
buttons except for ejecting the magazine. Whenever
a
CD magazine with discs is loaded in the changer, CD
will appear on the radio display.
If the CD changer is
checking the magazine for CDs, CD will flash on the
display until the changer is ready to play. When a CD
begins playing, CD will appear in the bottom left corner
and a disc and track number will be displayed. The disc
numbers are listed on the front of the magazine.
PUSHBUTTONS: Ress buttons one through six to
go from one compact disc to another that
is loaded in
the changer.
REV (1): Press and hold this button to reverse
quickly through a track selection. The display will
show elapsed time.
FWD (2): Press and hold this button to advance to a
passage quickly. The display will show elapsed time.
PROG (3): Press this button to go to the next track.
Each time you press PROG, the disc number on the
radio display will increment to the next available CD. If
one of your CD’s cannot be played, its number will be
skipped when selecting discs with PROG.
RANDOM (5): Press pushbutton number 5 to hear
the tracks in random, rather than sequential, order. RDM
will appear on the display when you press this button. If
you press
PROG or SEEK while RDM is displayed,
the next disc will be selected randomly.
If you press
SCAN while RDM is displayed, discs will be scanned
randomly. Press pushbutton number
5 again to turn off
the RANDOM feature.
AM-FM: Press this button to play the radio when a disc
is in the player.
SEEK: Press the down arrow to go to the start of the
current track if more than eight seconds have played.
If
you press SEEK again, the changer will go to the
previous track.
Press the up arrow to go to the next track.
SCAN: Press this button to listen to each selection for a
few seconds. The disc will go to the next selection, stop
for a
few seconds, then go on to the next selection. Press
this button again to stop scanning. The sound will be
muted and
SCAN will appear on the display.
TAPE-CD: Press this button if you have a disc loaded
in the changer and the radio is playing to play a compact
disc. Press
AM-FM to return to the radio when a
compact disc
is playing. Press TAPE-CD to switch
between the tape and compact disc if both are loaded.
EJECT Slide the CD changer door all the way open
and the disc will automatically eject.
3-16
ProCarManuals.com

SCAN: Press this button to listen to each selection for a
few seconds. The disc will go to the next selection, stop
for a few seconds, then go on to the next selection. Press
this button again to stop scanning. The sound will be
muted, SCAN will appear on the display and the disc
direction arrow will blink while scanning.
TONE: Press this button to select a TONE while
playing a compact disc. The tone will be automatically
set whenever you play a compact disc.
TAPE CD: Press this button to change to the tape or
disc function when the radio is on and either a tape or
CD is inserted. Press
AM/FM to return to the radio
while a CD or tape is playing. The inactive tape or CD
will remain safely inside the’ radio for future listening.
EJECT Press this button to remove the compact disc or
cassette tape. The item with the box around it on the
display will eject and the radio will play. EJECT may be
activated with either the ignition or radio off. Cassettes
and compact discs may be loaded with the radio and
ignition off
if this button is pressed first.
Theft-Deterrent Feature
THEFTLOCK” is designed to discourage theft of your
radio. It works by using a secret code
to disable all radio
functions whenever battery power is removed.
The THEFTLOCK feature for the radio may be used or
ignored. If ignored, the system plays normally and the
radio
is not protected by the feature. If THEFTLOCK is
activated, your radio will not operate if stolen.
When THEFTLOCK is activated, the radio will display
LOC to indicate a locked condition anytime battery
power
is removed. If your battery loses power for any
reason, you must unlock the radio with the secret code
before it will operate.
Activating the Theft-Deterrent Feature
The instructions which follow explain how to enter your
secret code to activate the THEFTLOCK system. It is
recommended that
you read through all nine steps
before starting the procedure.
NOTE:
If you allow more than 15 seconds to elapse
between any steps, the radio automatically reverts to
time and you must start the procedure over at Step
4.
ProCarManuals.com