clock Oldsmobile Aurora 1997 s User Guide

5. Raise the vehicle by rotating the wheel wrench
clockwise in the jack. Raise the vehicle far enough
off the ground so there’s enough room for the spare
tire
to fit.
6. Remove all the wheel nuts and take off the flat tire.
7. Remove any rust or dirt
from the wheel bolts,
mounting surfaces and
spare wheel.
Rust or dirt on the wheel, or on the parts to
which it is fastened, can make the wheel nuts
become loose after
a time. The wheel could come
off and cause an accident. When you change
a
wheel, remove any rust or dirt from the places
where the wheel attaches to the vehicle. In an
emergency,
you can use a cloth or a paper towel
to do this; but be sure to use
a scraper or wire
brush later, if you need to, to get all the rust or
dirt off.
5-29

Never use oil or grease on studs or nuts. If you
do, the nuts might come loose. Your wheel could
fall
off, causing a serious accident.
~ ~~
8. Place the spare tire on the wheel mounting surface.
9. Replace the wheel nuts
with the rounded end
of
the nuts toward the
wheel. Tighten each nut
by hand until
the wheel
is held against the hub.
If a nut cannot be
tightened by hand, use
the wrench, and see
your retailer right away.
10. Lower the vehicle by rotating the wheel wrench counterclockwise on the jack. Lower the
jack completely.
5-30

The fuel door can be opened
manually in case
of an
electrical power failure. To
do
so, first open the trunk.
The release mechanism
is
on the driver’s side of the
vehicle, at the top of
the
trunk compartment. Pull the
tab toward you to release
the fuel door.
I NOTICE:
Prying on a locked fuel filler door could damage
it. Use the remote fuel
door manual release
located in the trunk.
While refueling, hang the cap inside the fuel door. Twist
it clockwise to secure
it, if necessary.
To take
off the cap, turn it slowly to the left
(counterclockwise).
6-6

If you get gasoline on yourself and then
something ignites it,
you could be badly burned.
Gasoline can spray out on you if you open the
fuel filler cap too quickly. This spray can happen
if your tank is nearly full, and is more likely in
hot weather. Open the fuel filler cap slowly and
wait for any “hiss” noise to stop. Then unscrew the cap
all the way.
Be careful not to spill gasoline. Clean gasoline from
painted surfaces as soon as possible. See “Cleaning the
Outside of Your Aurora”
in the Index. When
you put the cap back
on, turn it to the right
(clockwise) until you hear a clicking sound. Make sure
you fully install the cap. The diagnostic system can
determine
if the fuel cap has been left off or improperly
installed. Ths would allow fuel to evaporate into the
atmosphere. See “Malfunction Indicator
Lamp” in
the Index.
NOTICE:
If you need a new cap, be sure to get the right
type. Your retailer can get one for you.
If you get
the wrong type, it may not fit or have proper
venting, and your fuel tank and emissions system
might be damaged.
6-7

2. Release tension of the wing screw clamp on the air
intake duct where it attaches to the
air cleaner cover
near the top
of the engine. Just turn the wing screw
counterclockwise, then detach the duct from the air
cleaner cover.
3. Push the duct and resonator assembly rearward and
up, and hold out
of the way.
4. There’s a temperature sensor on the corner of the air
cleaner cover. Release the sensor’s electrical
connector retainer, and pull up.
6-16

2. Release tension of the wing screw clamp on the air
intake duct where it attaches to the air cleaner cover
near the top of the engine.
Turn the wing screw
counterclockwise, then detach the hose
from the air
cleaner cover.
3. To remove the air cleaner cover, push the duct and
resonator assembly rearward and up, and hold them
out
of the way.
cover and tube.
4. Reverse the instructions to replace the air cleaner
Low-Beam Headlamp Bulbs
If you need to replace a headlamp bulb, do
the following:
1. Remove the two bolts and pull out the headlamp
assembly for more hand clearance.
2. Twist the bulb assembly one-sixth of a turn
counterclockwise and pull out the bulb assembly.
6-35

Front Turn Signal
The turn signal bulb is on the inboard edge of the
headlamp assembly.
To replace a bulb, do the following:
1.
2.
3.
4.
Remove the headlamp assembly if you need more
hand clearance.
Reach in and press the locking tab while twisting the
bulb assembly one-quarter of a turn
counterclockwise.
Replace the bulb and reverse Step
2 to reassemble.
If you removed the headlamp assembly, reassemble
it by aligning the pin and tightening the two bolts to
secure
it.
Headlamp Aiming
Your vehicle has the composite headlamp system. These
headlamps have horizontal and vertical aim indicators.
The aim has been pre-set at the factory and should need
no further adjustment.
If your vehicle is damaged in an accident and the
headlamp aim seems
to be affected, see your Aurora
retailer. Headlamps on damaged vehicles may require
recalibration
of the horizontal aim by your Aurora retailer.
To check the aim, the vehicle should be properly
prepared as
follows:
e
0
e
The vehicle must have all four tires on a perfectly
level surface.
The vehicle should not have
any snow, ice or mud
attached to it.
There should not be any cargo or loading of the
vehicle, except it should have a full tank
of gas and
one person or
160 lbs. (75 kg) on the driver’s seat.
Tires should be properly inflated.
I NOTICE:
To make sure your headlamps are aimed
properly, read all the instructions before
beginning. Failure to
follow these instructions
could cause damage to headlamp parts.
State inspection stations will allow a vertical reading of
plus
0.76 degrees or minus 0.76 degrees from the center
of the bubble.
It is recommended that the upper limit not exceed plus
0.4 degrees from the center of the bubble. Other drivers
may flash their high beams at
you if your adjustment is
much above plus
0.4 degrees.
6-37

5. Twist the socket one-quarter of a turn
counterclockwise and pull to remove.
6. Replace the bulb and reverse Steps 1 through 4 to
replace the assembly and tighten the bolts.
Interior Lamps
Front and Rear Reading Lamps
To change the bulbs in the front and rear reading lamps,
do the following:
1. Carefully insert a flat head screwdriver in the slot
between
the lens cover and molding.
2. Gently pry the lens cover away to expose the reading
lamp bulb. The lens cover should pop off.
new bulb.
3. Remove the bulb from its assembly and install a
4. Snap the lens cover back in place.

Right Front Passenger ......................... 3-10
Steering Wheel
............................... 3- 10
Clock. Setting the
............................... 3- 11
Comfort Controls
................................ 3-2
Compact Disc Care
............................. 3-30
Compact Disc Changer. Trunk Mounted
............. 3-22
Compact Disc Errors
.......................... 3-24
Loading the Magazine
......................... 3-22
Playing a Compact Disc
........................ 3-24
Compact.Disc Player
....................... 3-15. 3-21
Errors
................................. 3.15. 3.21
Compact Spare Tire
............................. 5-34
Control
of a Vehicle .............................. 4-6
ConvenienceNet
............................... 2-56
Convex Outside Mirror
.......................... 2-54
Coolant
....................................... 6-21
Heater. Engine
............................... 2-24
SurgeTank
.................................. 5-19
TemperatureGage
............................ 2-74
Cooling System
................................ 5-17
Cornering Lamps
............................... 2-45
CourtesyLamps
................................ 2-47
Courtesy Transportation
........................... 8-6
Cruise Control ................................. 2-40
Customer Assistance Information
................... 8- 1
Customer Satisfaction Procedure .................... 8-2
Damage. Finish
............................... 6-59
Damage. Sheet Metal
............................ 6-58
Date Display
................................... 2-85
Daytime Running Lamps ......................... 2-44
Customer Assistance
for Text Telephone Users
......... 8-4
DeadBattery
................................... 5-3 Defects. Reporting Safety
......................... 8-8
Defensive Driving ............................... 4-2
Defogger. Rear Window
.......................... 3-9
Defogging
..................................... 3-9
Defrosting
..................................... 3-9
Delayed Illumination
............................ 2-47
Delayed Locking
............................... 2-12
Dimensions. Vehicle
............................ 6-74
Distan e to Destination
.......................... 2-84
Dolby
& B Noise Reduction .................. 3.14. 3.20
Door AjarReminder
................................ 2-5
Central Unlocking System
....................... 2-4
Drive Position. Automatic Transaxle
................ 2-27
Driver Information Center
........................ 2-80
Driver Position
................................. 1 . 11
Driving
City
........................................ 4-21
Defensive
.................................... 4-2
Drunken
..................................... 4-3
Freeway
.................................... 4-22
InaBlizzard
................................. 4-28
IntheRain
.................................. 4-18
Night
...................................... 4-16
OnCurves
.................................. 4-11
On Hill and Mountain Roads
.................... 4-24
on Snow or Ice
............................... 4-27
Throughwater
............................... 4-20
WetRoads
.................................. 4-18
Winter
...................................... 4-26
With a Trailer
................................ 4-36
DIC
.......................................... 2-80
Locks
....................................... 2-4
On Grades While Towing a Trailer
............... 4-37
9-3