light Oldsmobile Aurora 2001 s Owner's Guide

2-50
Mirrors
Electrochromic Day/Night Rearview Mirror
with Compass
Your vehicle has an electrochromic inside rearview
mirror with a compass. Your vehicle's mirror may also
contain OnStar

controls.
This is the on/off button for mirrors equipped
with OnStar controls.
Pressing the MIRROR button (or the on/off button for
mirrors equipped with OnStar controls) located at the
bottom of the mirror, turns the automatic dimming
feature on or off.
The mirror also includes an eight
-point compass display
in the upper right corner of the mirror face. When on, the
compass automatically calibrates as the vehicle is driven.
When cleaning the mirror, use a paper towel or similar
material dampened with glass cleaner. Do not spray
glass cleaner directly on the mirror as that may cause
the liquid cleaner to enter the mirror housing.Mirror Operation
To turn on the automatic dimming feature, press MIRROR
(or press and hold the on/off button for about three seconds
for mirrors equipped with OnStar controls). To turn off
automatic dimming, press MIRROR (or press and hold
the on/off button for about three seconds for mirrors
equipped with OnStar controls) again. The green indicator
light will be illuminated when this feature is active.
The automatic dimming feature will be active each time
the vehicle is started.
Compass Operation
Press COMPASS (or the on/off button for mirrors equipped
with OnStar controls) once to turn the compass on or off.
When the ignition and the compass feature are on, the
compass will show two character boxes for approximately
two seconds. After two seconds, the mirror will display the
compass heading.
Compass Calibration
If after two seconds, the display does not show a compass
heading (ªNº for North, for example), there may be a
strong magnetic field interfering with the compass. Such
interference may be caused by a magnetic antenna mount,
magnetic note pad holder or a similar magnetic item.
If the letter ªCº should ever appear in the compass
window, the compass may need calibration.

2-54 Rear Storage Compartment (Option)
Your vehicle may have a rear storage armrest with
cupholders and a pass
-through feature.
Lift the front of the cover on the armrest to reveal the
storage space.
Pull down the interior door to access the trunk.
Convenience Net
Your vehicle has a convenience net just inside the back
wall of the trunk.
Put small loads, like grocery bags, behind the net. It can
help keep them from falling over during sharp turns or
quick starts and stops.
The net isn't for larger, heavier loads. Store them in the
trunk as far forward as you can. You can unhook the net
so that it will lie flat when you're not using it.
Ashtrays and Cigarette Lighter
Push and release the cover to reveal the front ashtray
and cigarette lighter.
NOTICE:
Don't put papers and other things that burn
into your ashtrays. If you do, cigarettes or
other smoking materials could set them on fire,
causing damage.
To clean an ashtray, make sure the cover is open fully,
then lift out the ashtray by pulling on the snuffer.
To use a lighter, push the center all the way in and let
it go. When it's ready, the center will pop back out by
itself. Pull out the entire unit to use it.

2-55
NOTICE:
Don't hold a cigarette lighter in with your hand
while it is heating. If you do, it won't be able to
back away from the heating element when it's
ready. That can make it overheat, damaging the
lighter and the heating element.
The cigarette lighter will only operate when the ignition
is in RUN and for 10 minutes after turning the ignition
off. If you would like the lighter to operate regardless of
the ignition position, and for unlimited periods of time,
see ªEngine Compartment Bussed Electrical Centerº in
the Index or see your dealer.
Leaving an accessory on for a long period of time can
drain the vehicle's battery.
Sun Visors
To block out glare, you can swing down the visors. You
can also remove them from the center mount and swing
them to the side, while the auxiliary visor remains to
block glare from the front.
To extend the visor at the sides, pull out the extension.
Illuminated Visor Vanity Mirrors
When you open the cover to the driver or passenger side
visor vanity mirror, the lamps will come on.

2-57
Assist Handles
A handle above each rear door and the front passenger's
door can be used to help you get in or out of your vehicle.
Garment Hook
For your convenience, you will find a two-hanger
capacity garment hook on each rear door assist handle.
Garment hooks are not designed to support clothing
bars. Use assist handles for this if possible.
Sunroof (Option)
If you have this feature,
the switches are located
between the sun visors.
There are two switches that operate the sunroof. The
switches will only work when the ignition is on or when
the Retained Accessory Power (RAP) is active.The OPEN/CLOSE switch has positions for open or
close and express open. The TILT/CLOSE switch has
positions for tilt or close.
Press and hold the OPEN/CLOSE switch to the
first position to open the glass panel and sunshade.
The sunshade can also be opened by hand. To close
the glass panel, press and hold the OPEN/CLOSE or
TILT/CLOSE switch in the close position. As the
glass panel closes, it will open slightly towards the tilt
position to provide a better seal. The sunshade can only
be closed by hand.
Press and release the OPEN/CLOSE switch rearward
to the second position to express open the glass panel.
It will stop in a partially open position. The glass panel
may be fully opened by pressing the OPEN/CLOSE
switch rearward again. When the glass panel is express
opening, pressing either switch in any direction will stop
it. If you press and hold the OPEN/CLOSE switch in
the express open position for more than one and a half
seconds, the express open operation will be overridden
and the sunroof will operate manually.
To tilt open the glass panel, press and hold the
TILT/CLOSE switch. The sunshade must be opened
by hand. To close the glass panel, press and hold
the TILT/CLOSE or OPEN/CLOSE switch in the
close position.

2-59
Your vehicle's engine should be turned off while
programming the transmitter. Follow these steps to
program up to three channels:
1. If you have previously programmed a transmitter
channel, proceed to Step 2. Otherwise, hold
down the two outside buttons on the HomeLink
Transmitter until the indicator light begins to flash
rapidly (after 20 seconds). Then release the buttons.
This procedure initializes the memory and erases any
previous settings for all three channels.
2. Decide which one of the three channels you want to
program. Hold the end of the hand
-held transmitter
about 2 to 5 inches (5 to 13 cm) away from the
surface of the HomeLink Transmitter so that you
can still see the indicator light.
3. Using both hands, press the hand
-held transmitter
button and the desired button on the HomeLink
Transmitter. Continue to press both buttons
through Step 4.
4. Hold down both buttons until you see the indicator
light on the HomeLink Transmitter flash slowly and
then rapidly. The rapid flashing indicates that the
HomeLink Transmitter has been programmed.
Release both buttons once the indicator light starts
to flash rapidly.If you have trouble programming the HomeLink
Transmitter, make sure that you have followed the
directions exactly as described. The HomeLink
Transmitter may not work with older garage door openers
that do not meet current Federal Consumer Safety
Standards. If you cannot program the transmitter after
repeated attempts, refer to ªRolling Code Programmingº
later in this section or contact the HomeLink Transmitter
manufacturer at 1
-800-355-3515.
Be sure to keep the original hand
-held transmitter
in case you need to erase and reprogram the
HomeLink Transmitter.
Note to Canadian Owners: During programming,
the hand
-held transmitter may automatically stop
transmitting after one or two seconds. In this case, you
should press and repress the button on the hand
-held
transmitter every two seconds without ever releasing the
button on the HomeLink Transmitter. Release both
buttons when the indicator light on the HomeLink
Transmitter begins to flash rapidly.

2-60 Operating the HomeLink

Transmitter
Press and release the appropriate button on the
HomeLink Transmitter. The indicator light comes on
while the signal is being transmitted. The trunk release
lockout switch must be OFF.
If the hand
-held transmitter appears to program the
HomeLink Transmitter but does not open your garage
door, and if the garage door opener was manufactured
after 1996, the garage door opener may have a ªrolling
codeº system. A rolling code system changes the code
of the garage door opener every time you open or close
the garage door.
To determine if you have this system, press the button
on the HomeLink Transmitter that you have already
programmed. If the indicator light on the HomeLink
Transmitter flashes rapidly for two seconds and then
turns solid, the garage door opener has a rolling code
system. In a rolling code system, the garage door motor
head unit must be trained to the HomeLink Transmitter.
ªRolling Codeº Programming (If Equipped)
If you have not previously programmed the hand-held
transmitter to the HomeLink Transmitter, see
ªProgramming the HomeLink

Transmitterº listed
previously. If you have completed this programming
already, you now need to train the garage door opener
motor head unit to recognize the HomeLink Transmitter.
Refer to your garage door opener owner's manual for
the proper transmitter training procedure for your garage
door opener brand.
1. Find the training button on the garage door opener
motor head unit. The exact location and color of
the button may vary by garage door opener brand.
If you have difficulty finding the training button,
refer to your garage door opener owner's manual.
2. Press the training button on the garage door
opener motor head unit.
Following this step, you have 30 seconds to
start Step 3.

2-61
3. Return to the HomeLink Transmitter in your
vehicle and firmly press and release the HomeLink
Transmitter button you have already programmed for
two to three seconds. Press and release the button
again (you may need to do this step up to three
times) to make sure that the HomeLink Transmitter
has been trained to the garage door opener motor
head unit. Check that the training was successful.
The garage door opener should now recognize the
HomeLink Transmitter. You may either use the
HomeLink Transmitter or the hand
-held transmitter
to open the garage door.
If after following these instructions, you still have problems
training the garage door opener, contact the HomeLink
Transmitter manufacturer at 1
-800-355-3515.
Erasing Channels
To erase all three programmed channels, hold down the
two outside buttons until the indicator light begins to
flash (after 20 seconds). Release both buttons.
Accessories
Accessories for the HomeLink
Transmitter are available
from the manufacturer of the unit. If you would like
additional information, please call 1
-800-355-3515.

2-64
Instrument Panel Cluster
Your vehicle is equipped with this instrument panel cluster, which includes indicator warning lights and gages that are
explained on the following pages. The instrument panel is designed to let you know at a glance how your vehicle is
running. You'll know how fast you're going, how much fuel you're using, and many other things you'll need to drive
safely and economically.
United States version shown, Canada similar

2-66 Tachometer
The tachometer displays the engine speed in revolutions
per minute (rpm).
If your engine speed equals or exceeds the safe limit for
operation, the message HOT...REDUCE ENG RPM is
displayed on the Driver Information Center (DIC).
NOTICE:
Do not operate the engine with the tachometer in
the red area, or when the message HOT...REDUCE
ENG RPM is displayed. Engine damage may occur.
Warning Lights, Gages and Indicators
This part describes the warning lights and gages that
may be on your vehicle. The pictures will help you
locate them.
Warning lights and gages can signal that something is
wrong before it becomes serious enough to cause an
expensive repair or replacement. Paying attention to
your warning lights and gages could also save you or
others from injury.
Warning lights come on when there may be or is a
problem with one of your vehicle's functions. As you
will see in the details on the next few pages, some
warning lights come on briefly when you start the
engine just to let you know they're working. If you are
familiar with this section, you should not be alarmed
when this happens.

2-67
Gages can indicate when there may be or is a problem
with one of your vehicle's functions. Often gages and
warning lights work together to let you know when
there's a problem with your vehicle.
When one of the warning lights comes on and stays on
when you are driving, or when one of the gages shows
there may be a problem, check the section that tells you
what to do about it. Please follow this manual's advice.
Waiting to do repairs can be costly
-- and even
dangerous. So please get to know your warning lights
and gages. They're a big help.
Your vehicle has a Driver Information Center that works
along with the warning lights and gages. See ªDriver
Information Centerº in the Index.
Safety Belt Reminder Light
When the key is turned to RUN or START, a chime will
come on for about eight seconds to remind people to
fasten their safety belts.
The safety belt light will
also come on and stay on
for about 20 seconds, then
flash for about 55 seconds.
If the driver's belt is already buckled, the chime will not
sound and the light will go off after 5 seconds.