seat adjustment Oldsmobile Aurora 2001 Owner's Manuals
[x] Cancel search | Manufacturer: OLDSMOBILE, Model Year: 2001, Model line: Aurora, Model: Oldsmobile Aurora 2001Pages: 376, PDF Size: 2.67 MB
Page 14 of 376

1-2
Seats and Seat Controls
This part tells you about the power seats -- how to
adjust them, and also about reclining front seatbacks,
lumbar adjustments and heated seats.
Manual Lumbar Support
The knob that controls this feature is located on the
outboard side edge of the seat. Turn the knob towards
the front of the vehicle to increase lumbar support.
Turn the knob towards the rear of the vehicle to decrease
lumbar support.
Power Seats
The power seat controls are located on the outboard side
of each front seat.
Page 15 of 376

1-3
To adjust the power seats:
Horizontal Control: Raise or lower the front of the seat
by pressing the forward edge of the control up or down.
Raise or lower the rear of the seat by holding the rear
edge of the control up or down.
Move the seat forward or rearward by pressing the
control towards the front or rear of the vehicle.
Move the seat higher or lower by holding the control up
or down.
Vertical Control (Option): Move the seatback into a
reclined position by pressing back on the control. Raise
the seatback by pressing forward on the control.Power Lumbar Control (Option)
The power lumbar controls
are located on the outboard
side of each front seat.
Use the power seat control first to get the proper
position, then continue with the lumbar adjustment.
To reshape the lower seatback, press the lumbar control
forward to increase support and rearward to decrease
support. Press the control up or down to raise or lower
the support mechanism.
Keep in mind that as your seating position changes,
as it may during long trips, so should the position of
your lumbar support. Adjust the seat as needed.
Page 16 of 376

1-4 Memory Seat and Mirrors (If Equipped)
If your vehicle has this
feature, the controls on
the driver's door panel
are used to program and
recall previous settings.
You can use this feature to save your driver's seat
position, lumbar adjustment, outside mirror positions,
personalization features, comfort controls and
radio settings.Adjust the driver's seat (including the lumbar
adjustments) and both outside mirrors to the position
you would like for driving. Then press and hold memory
button 1 for more than three seconds. A double beep
will sound when the memory is set.
To set the seat and mirror positions for a second driver,
follow the previous steps, but press button 2 instead.
You can also store an exit position for each driver. The
exit position is programmed by moving the seat to the
desired exit position and then holding the exit button for
more than three seconds. The exit position set will be for
the most recently selected driving position (1 or 2).
Please note that mirror and lumbar positions will not be
stored or recalled for the exit position.
Page 295 of 376

6-40
If your vehicle is damaged in an accident, the headlamp
aim may be affected. Aim adjustment to the low beam
may be necessary if it is difficult to see lane markers
(for horizontal aim), or if oncoming drivers flash their
high beams at you (for vertical aim). If you believe your
headlamps need to be re
-aimed, we recommend that you
take your vehicle to your dealer for service. However, it
is possible for you to re
-aim your headlamps as
described in the following procedure.
NOTICE:
To make sure your headlamps are aimed
properly, read all the instructions before
beginning. Failure to follow these instructions
could cause damage to headlamp parts.
The vehicle should be properly prepared as follows:
The vehicle should be placed so the headlamps are
25 ft. (7.6 m) from a light colored wall or other
flat surface.
The vehicle must have all four tires on a perfectly
level surface which is level all the way to the wall or
other flat surface.
The vehicle should be placed so it is perpendicular to
the wall or other flat surface.
The vehicle should not have any snow, ice or mud
attached to it.
The vehicle should be fully assembled and all other
work stopped while headlamp aiming is being done.
The vehicle should be normally loaded with a full
tank of fuel and one person or 160 lbs. (75 kg) on the
driver's seat.
Tires should be properly inflated.
Headlamp aiming is done with the vehicle low beam
lamps. The high beam lamps will be correctly aimed if
the low beam lamps are aimed properly.
The headlamp aiming devices are under the hood near
the headlamps.