seat memory Oldsmobile Aurora 2001 Owner's Manuals

Table of Contents
Keys and Door Locks
Remote Lock Control
Trunk Release
Automatic Transaxle
Parking Brake
Windows
Tilt Wheel
Turn Signal/Multifunction Lever
Windshield Wipers
Cruise Control
Interior and Exterior LampsMirrors
Storage Compartments
Convenience Net
Accessory Power Outlet
OnStar® System (If Equipped)
Sunroof (Option)
HomeLink® Transmitter (If Equipped)
Instrument Panel, Warning Lights and Gages
Driver Information Center
Memory and Personalization Seats and Seat Controls
Safety BeltsAir Bag Systems
Child Restraints
Section
1
Section
2
Seats and Restraint Systems
Features and Controls
ii

1-4 Memory Seat and Mirrors (If Equipped)
If your vehicle has this
feature, the controls on
the driver's door panel
are used to program and
recall previous settings.
You can use this feature to save your driver's seat
position, lumbar adjustment, outside mirror positions,
personalization features, comfort controls and
radio settings.Adjust the driver's seat (including the lumbar
adjustments) and both outside mirrors to the position
you would like for driving. Then press and hold memory
button 1 for more than three seconds. A double beep
will sound when the memory is set.
To set the seat and mirror positions for a second driver,
follow the previous steps, but press button 2 instead.
You can also store an exit position for each driver. The
exit position is programmed by moving the seat to the
desired exit position and then holding the exit button for
more than three seconds. The exit position set will be for
the most recently selected driving position (1 or 2).
Please note that mirror and lumbar positions will not be
stored or recalled for the exit position.

1-5
To recall your memory positions, your vehicle must be in
PARK (P). Push and release the memory button (1 or 2)
corresponding to the desired driving position. The seat and
mirrors will move to the position previously stored for the
identified driver. You will hear one beep.
To recall the exit position, your vehicle must be in
PARK (P). Push and release the EXIT button and the
seat will move to the exit position previously stored for
the current identified driver. You will hear one beep.
If an exit position has not been stored for the current
identified driver, the seat will move all the way back.
To stop recall movement of the seat at any time, press
one of the power seat controls located on the outboard
side of each front seat.
If you would like your stored driving or exit position
to be recalled when unlocking your vehicle with the
transmitter, see ªDIC Personalizationº in the Index.Heated Front Seat (Option)
The heated seat controls
are located next to the
console shifter.
Push the ON part of the button once for a HI setting or
twice for a LO setting. Push the OFF part of the button
to turn the heated seat off. The LO setting warms the
seatback and cushion until the seat approximates body
temperature. The HI setting heats the seatback and
cushion to a slightly higher temperature.
The heated seats can only be used when the ignition
is turned on. The heating elements in the seats
automatically turn off when the vehicle's ignition is
turned off.

2-52 Power Remote Control Mirror
The controls on the driver's door operate both outside
rearview mirrors. Move the L/R switch to the left (L)
to select the driver's side rearview mirror, or to the
right (R) to select the passenger's side rearview mirror.
Then press the arrows on the four
-way pad to adjust
each mirror so that you can see a little of the side of
your vehicle when you are sitting in a comfortable
driving position.Leave the L/R switch in the center position to disable
mirror movement by the four
-way control pad.
If your vehicle is equipped with the memory function,
the mirrors and driver's seat position, can be stored into
memory. See ªMemory Seat and Mirrorsº in the Index.
Parallel Park Assist Mirror (If Equipped)
If you have the memory seat and mirrors feature,
the passenger's outside rearview mirror also includes a
tilt
-down feature that operates when the shift lever is
in REVERSE (R). When the vehicle is shifted out of
REVERSE (R), the passenger mirror will return to its
original position after a five
-second delay. This delay
prevents movement of the mirror if multiple gear
transitions (REVERSE (R) to DRIVE (D) to
REVERSE (R)) occur during a parallel parking
maneuver. This feature can be programmed on or off
through the DIC. See ªDriver Information Centerº
or ªPersonalization Featuresº in the Index for
programming instructions. Vehicles are delivered
with this feature off.

2-83 DIC Personalization
The DIC can be used to program the following personal
choice features available with your vehicle:

Automatic Door Locks

Window Lockout

Security Feedback

Delayed Locking

Perimeter Lighting

Driver ID

Memory Seats

Parallel Park Assist Mirror (Tilt Mirror)
To access the personalization menu, the vehicle must be
in PARK (P) with the ignition in RUN and no warning
messages displayed on the DIC. You must then press
and hold both of the SELECT buttons for three seconds.
This will display the personalization menu.The DIC display will show the following:
FEATURE PROGRAMMING
PRESS SELECT DOWN TO
SELECT MENU OPTIONS
PRESS SELECT RIGHT TO
CHANGE SETTINGS
The next item to be displayed is DRIVER 1 or
DRIVER 2. To change the driver number, press the
SELECT right arrow. The driver number that you
select should correspond with the number on the back
of your remote lock control transmitter. Once the correct
driver number has been selected, press the SELECT
down arrow to enter your choice and move on to the
next selection.

2-84
The DIC is used to program the personal choices of
two drivers. The drivers are recognized as DRIVER 1
and DRIVER 2. You will let the DIC and the vehicle
know which driver you are by using your remote lock
control transmitter or by pressing the appropriate
memory seat control button located on the driver's door
or choosing the driver with the DIC. Each remote lock
control transmitter was pre
-programmed to belong to
DRIVER 1 or DRIVER 2. The personalization features
may be programmed differently for each driver.
When you press the unlock symbol on the transmitter,
the DIC will automatically change driver numbers and the
vehicle will recall the personal choice settings that were
last made to correspond to your transmitter, including
your radio and comfort control settings. See ªComfort
Controls, Personalizationº in the Index.
If you unlock the vehicle using your door key instead
of your transmitter, the personal choice settings will
correspond to the previous driver of the vehicle as
identified by a transmitter, a memory seat control or
through the DIC. If this happens and you were not
the last driver of the vehicle, press your correct driver
number on the memory seat controls, press the
unlock symbol on your transmitter or select the
personalization programming mode and choose the
correct driver number.After you have the correct driver number on the display
use the SELECT down arrow button to scroll through
the following messages and feature options:

DOORS LOCK IN GEAR
- YES/NO

DOORS UNLOCK
- YES/NO

ALL DOORS IN PARK
- YES/NO

ALL DOORS AT KEY OFF
- YES/NO

DRIVERS DOOR IN PARK
- YES/NO

DRIVERS DOOR KEY OFF
- YES/NO

PASS WINDOW LOCKOUT
- YES/NO

KEY FOB FLASH LIGHTS
- YES/NO

KEY FOB CHIRP HORN
- YES/NO

DELAY LOCK OF DOORS
- YES/NO

PERIMETER LIGHTS
- YES/NO

EXT LIGHT TIMEOUT
- 25

DISPLAY DRIVER ID
- YES/NO

KEY FOB MEMORY SEAT
- YES/NO

DRIVING POSITION
- YES

EXIT POSITION
- YES

TILT MIRROR REVERSE
- YES/NO

2-85
If you would like to exit the selection mode without
moving through each of the personal choice features,
simply press a different button on the DIC or turn off
the ignition. The personal choices you made will still
be retained, even without passing through each of the
features. In order for your personal choices to save,
you must press the SELECT down arrow after making
your selections.
If you happen to move past a selection you would like
to make a personal choice for, press unlock on your
transmitter or press the appropriate driver number on
the memory seat control. This will return you to the
beginning of the option feature programming mode.
A description of each feature programmable through
the DIC follows.
Automatic Door Locks
You can program the automatic door lock feature to
change to the following modes:
Mode 0: No automatic door lock or unlock.
Mode 1: All doors automatically lock when shifted out
of PARK (P). No automatic door unlock.Mode 2: All doors automatically lock when shifted out
of PARK (P). Only the driver's door automatically
unlocks when shifted into PARK (P).
Mode 3: All doors automatically lock when shifted out
of PARK (P). All doors automatically unlock when
shifted into PARK (P).
Mode 4: All doors automatically lock when shifted out
of PARK (P). Only the driver's door automatically
unlocks when the key is turned to LOCK.
Mode 5: All doors automatically lock when shifted out
of PARK (P). All doors automatically unlock when the
key is turned to LOCK.
You can change which mode your vehicle is in by
different selections of the following DIC displays:

DOORS LOCK IN GEAR
- YES/NO

DOORS UNLOCK
- YES/NO

ALL DOORS IN PARK
- YES/NO

ALL DOORS AT KEY OFF
- YES/NO

DRIVERS DOOR IN PARK
- YES/NO

DRIVERS DOOR KEY OFF
- YES/NO

2-89
Driver ID
This feature displays the driver ID, as identified by
the DIC. If you choose YES when DISPLAY
DRIVER ID is shown on the DIC, the driver number
will be displayed every time the ignition is turned on.
If you choose NO when DISPLAY DRIVER ID is
shown on the DIC, the driver number can be displayed
by pressing either a button on the remote lock control
transmitter or a memory seat button.
Memory Seat Recall (If Equipped)
This feature recalls the position of the driver's seat. When
this feature is active, the memory seat and mirror positions
will be recalled for the identified driver when the remote
lock control transmitter is used to enter the vehicle.
You can program this feature to be active by choosing
YES when the KEY FOB MEMORY SEAT choice
appears, or inactive by choosing NO when the KEY
FOB MEMORY SEAT choice appears on the DIC.
Make your choices by pressing the SELECT right
arrow button and store them in memory by pressing
the SELECT down arrow button.You can also program this feature to recall your memory
seat position or the exit seat position. Select YES for
KEY FOB MEMORY SEAT then use the SELECT
right arrow button to toggle between DRIVING
POSITION
- YES and EXIT POSITION - YES.
When the desired position is displayed on the DIC,
press the SELECT down arrow button to save that
position in memory and move on to the next selection.
For more information on this feature, see ªMemory Seat
and Mirrorsº in the Index.
Parallel Park Assist (If Equipped)
The parallel park assist mirror, which tips the passenger
mirror while the vehicle is in REVERSE (R), can be
made active or inactive through the DIC. When TILT
MIRROR REVERSE appears on the display, use the
SELECT right arrow button to toggle the arrow
between YES and NO. When you have made your
choice, press the SELECT down arrow button to record
your selection. For more information on this feature,
see ªMirrorsº in the Index.

6-73
Minifuses Usage
1 Fuel Pump
2 HVAC Blower
3 Memory
4 ALDL
5 Rear Fog Lamps
6CD
7 Driver's Door Module
8 Air Bag SystemMinifuses Usage
9 Not Used
10 Right Parking Lamp
11 Vent Solenoid
12 Ignition 1
13 Left Parking Lamp
14 Dimmer
15 Not Used
16 Left Front Heated Seat
17 Not Used
18 Rear Door Module
19 Stoplamp
20 NSBU
21 Audio
22 Retained Accessory Power (RAP)
23 Not Used
24 Not Used
25 Passenger Door Module
26 Body
27 Interior Lamps