reset OLDSMOBILE AURORA 2002 User Guide

2-86 Fuel Economy
Pressing the SELECT down arrow while in the
ECON mode displays average fuel economy and
instantaneous fuel economy calculated for your
specific driving conditions.
Average fuel economy will be shown in a reading
such as:
25.2 AVG MI/GAL or 9.3 AVG L/100 KM
Instantaneous fuel economy will be shown in a reading
such as:
28 INST MI/GAL or 8.4 INST L/100 KM
The average fuel economy is viewed as a long
-term
approximation of your overall driving conditions.
If you press and hold RESET for three seconds in this
mode while you're driving, the system will begin
figuring average fuel economy from that point in time.
Instantaneous fuel economy cannot be reset.
Oil Life
The GM Oil Life System
is the only function
accessible in the OIL mode. Engine oil life is displayed
in a reading such as the following:
OIL LIFE 30%
This is an estimate of the oil's remaining useful life.
It will show 100% when the system is reset after an oil
change. It will alert you to change your oil on a schedule
consistent with your driving conditions.
When the remaining oil life is low, the system will alert
you with this message:
CHANGE OIL SOON
Always reset the OIL LIFE reminder after an oil change.
To reset the oil life system, see ªOil Life Systemº in
the Index. Also, see ªEngine Oil, When to Changeº in
the Index.
Remember, you must reset the OIL LIFE yourself after
each oil change. It will not reset itself. Also, be careful
not to reset the OIL LIFE accidentally at any time other
than when the oil has just been changed. It can't be reset
accurately until the next oil change.
ProCarManuals.com

2-87
The DIC does not replace the need to maintain your
vehicle as recommended in the Maintenance Schedule in
this manual. Also, the oil change reminder will not
detect dusty conditions or engine malfunctions that may
affect the oil. If you drive in dusty areas, change your oil
after every 3,000 miles (5 000 km) or three months,
whichever occurs first, unless the DIC instructs you to
do so sooner. Also, the oil change reminder does not
measure how much oil you have in your engine. So, be
sure to check your oil level often. See ªEngine Oilº in
the Index.
Gage
Pressing the SELECT down arrow while in GAGE
mode will allow you to access the battery volts, oil
pressure and tire pressure displays. Pressing and holding
the RESET button for three seconds while in average
speed and tire pressure displays will reset them. Pressing
the SELECT down arrow in GAGE mode will show the
following displays:

Battery voltage, such as the following:
VOLTS: 13.8

Oil pressure, such as the following:
OIL PRESSURE 40 PSI or OIL
PRESSURE 276 KPA
Average speed, such as the following:
AVG SPEED 55 MPH or AVG SPEED 90 KM/H

Tire pressure status, such as the following:
TIRE PRESSURE NORMAL or TIRE
PRESSURE LOW
TIRE PRESSURE NORMAL appears when the
check tire pressure system believes your vehicle's
tire pressures are normal. If a potential tire pressure
problem is detected, the display will show TIRE
PRESSURE LOW. If you see this message, you
should stop as soon as you can and check all four
tires for damage. If a tire is flat, see ªIf a Tire Goes
Flat º in the Index. Also check the tire pressure in all
four tires as soon as you can. See ªTire Pressureº in
the Index.
There are times when you will have to reset
(calibrate) the check tire pressure system. Pressing
the RESET button while the TIRE PRESSURE
LOW warning is displayed does not automatically
reset the tire pressure monitoring system. See
ªCheck Tire Pressure Systemº in the Index for
more information.
ProCarManuals.com

2-95 DIC Warnings and Messages
Other messages or warnings may appear in the DIC
display. For Canadian drivers, in addition to the DIC
message your DIC will display EXP with a number after
it which reflects the following messages:
EXP (Export ID) Warning Message. . . . . . . . . . . .
1 AIR BAG PROBLEM. . . . . . . . . . . . . . . . . . . . . .
3 CHANGE OIL SOON. . . . . . . . . . . . . . . . . . . . . .
4 CHECK CHARGE SYSTEM. . . . . . . . . . . . . . . . .
5 CHECK OIL LEVEL. . . . . . . . . . . . . . . . . . . . . . .
6 TRANS HOT...IDLE ENG. . . . . . . . . . . . . . . . . . .
7 CONFIRM TIME & DATE. . . . . . . . . . . . . . . . . .
8 DRIVERS DOOR AJAR. . . . . . . . . . . . . . . . . . . .
9 ENGINE HOT...A/C OFF. . . . . . . . . . . . . . . . . . .
10 HOT...REDUCE ENG RPM. . . . . . . . . . . . . . . . .
11 HOT...STOP ENGINE *. . . . . . . . . . . . . . . . . . . .
12 THEFT SYSTEM FAULT. . . . . . . . . . . . . . . . . .
13 LEFT REAR DOOR AJAR. . . . . . . . . . . . . . . . .
14 LOW BRAKE FLUID *. . . . . . . . . . . . . . . . . . . .
15 LOW ENGINE COOLANT. . . . . . . . . . . . . . . . .
16 LOW FUEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17 LOW OIL PRESSURE *. . . . . . . . . . . . . . . . . . . 18 LOW TIRE PRESSURE. . . . . . . . . . . . . . . . . . .
19 LOW WASHER FLUID. . . . . . . . . . . . . . . . . . . .
20 PARK BRAKE SET *. . . . . . . . . . . . . . . . . . . . .
21 PASSENGER DOOR AJAR. . . . . . . . . . . . . . . .
22 RIGHT REAR DOOR AJAR. . . . . . . . . . . . . . . .
23 SERVICE VEHICLE SOON. . . . . . . . . . . . . . . .
24 TURN SIGNAL ON?. . . . . . . . . . . . . . . . . . . . . .
25 THEFT ATTEMPTED. . . . . . . . . . . . . . . . . . . . .
26 SERV STABILITY SYS. . . . . . . . . . . . . . . . . . . .
27 HEADLAMPS SUGGESTED. . . . . . . . . . . . . . .
28 TRUNK AJAR. . . . . . . . . . . . . . . . . . . . . . . . . . .
29 BATTERY SAVER ACTIVE. . . . . . . . . . . . . . . .
32 HOT...IDLE ENGINE. . . . . . . . . . . . . . . . . . . . .
33 STARTING DISABLED *. . . . . . . . . . . . . . . . . .
36 CHECK GAS CAP. . . . . . . . . . . . . . . . . . . . . . . .
42 STABILITY ACTIVE. . . . . . . . . . . . . . . . . . . . .
The EXP codes are used to make translation from
English to other languages easier.
Pressing the RESET button will remove the above
messages or warnings from the DIC display, unless
noted by an asterisk (*).
ProCarManuals.com

2-96
CHECK OIL LEVEL - 5: If you ever see the
CHECK OIL LEVEL message, it indicates that the
engine oil level is 1 to 1 1/2 quarts (0.9 L to 1.4 L) low.
The message will appear only if the engine is running
and it has been at least eight minutes since the engine
was last running. If the message appears, check the oil
dipstick level. If it reads low, your oil level should be
brought up to the proper level (see ªEngine Oilº in the
Index). After bringing the oil to the proper level, the
ignition must be off for eight minutes to allow the
majority of oil to drain into the oil pan.
SERV STABILITY SYS
- 26: If you ever see the
SERV STABILITY SYS message, it means there may
be a problem with your stability enhancement system. If
you see this message, try to reset the system (stop; turn
off the engine; then start the engine again). If the SERV
STABILITY SYS message still comes on, it means there
is a problem. You should see your dealer for service.
Reduce your speed and drive accordingly.STABILITY ACTIVE
- 42: You may see the
STABILITY ACTIVE message on the Driver
Information Center. It means that an advanced,
computer
-controlled system has come on to help your
vehicle continue to go in the direction in which you're
steering. This stability enhancement system activates
when the computer senses that your vehicle is just
starting to spin, as it might if you hit a patch of ice or
other slippery spot on the road. When the system is on,
you may hear a noise or feel a vibration in the brake
pedal. This is normal.
When the STABILITY ACTIVE message is on, you
should continue to steer in the direction you want to go.
The system is designed to help you in bad weather or
other difficult driving situations by making the most of
whatever road conditions will permit. If the STABILITY
ACTIVE message comes on, you'll know that
something has caused your vehicle to start to spin, so
you should consider slowing down.
ProCarManuals.com

3-12
To scan preset stations, press and hold either SCAN
arrow for more than four seconds, PRESET SCAN will
appear on the display. You will hear a double beep and
the P will blink with the preset number. The radio will
go to the first preset station stored on your pushbuttons,
play for a few seconds, then go on to the next preset
station. Press either SCAN arrow again to stop scanning
presets. The radio will scan preset stations with a strong
signal only. The sound will mute while scanning.
Setting Preset Stations
The six numbered pushbuttons let you return to your
favorite stations. You can set up to 18 stations (six AM,
six FM1 and six FM2), by performing the following steps:
1. Turn the radio on.
2. Press BAND to select the band.
3. Tune in the desired station.
4. Press AUTO EQ to select the equalization that best
suits the type of station selected.
5. Press and hold one of the six numbered pushbuttons
until you hear a beep. Whenever you press that
numbered pushbutton, the station you set will return
and the equalization that you selected will also be
automatically selected for that pushbutton.
6. Repeat the steps for each pushbutton.Setting the Tone (Bass/Treble)
AUDIO: Press the AUDIO button until BASS, MID
or TREB appears on the display. Press the knob above
the AUDIO button to extend it, then turn the knob to
increase or decrease. When you use this knob, the
radio's tone setting will switch to manual. If a station is
weak or noisy, you may want to decrease the treble.
Press and hold the AUDIO button for at least two
seconds to return all tone settings, including balance
and fade to flat.
AUTO EQ (Automatic Equalizer): This feature
allows you to choose preset bass, midrange and treble
equalization settings designed for country, jazz, talk,
pop, rock and classical program types.
The program type last chosen will appear on the display
when you first press AUTO EQ. Each time you press
this button, another program type will appear on the
display and AUTO EQ will switch to one of the preset
program types.
To return to the manual mode, press the AUTO EQ
button until MANUAL appears on the display. Then you
will be able to manually adjust the bass, midrange and
treble using the AUDIO button.
ProCarManuals.com

3-13
If your vehicle has the Bose radio, the AUTO EQ button
will work the same, except the radio will display EQ1
through EQ6 as the choices instead of displaying the
equalization setting names. These settings can be used
while listening to the radio or the CD player.
The radio saves separate AUTO EQ settings for each
preset and source.
Adjusting the Speakers (Balance/Fade)
AUDIO: To adjust the balance between the right
and left speakers, press the AUDIO button until BAL
appears on the display. Press the knob above the AUDIO
button to extend it, then turn the knob to adjust the
sound to the left or right speakers. The middle position
balances the sound between the speakers.
To adjust the fade between the front and rear speakers,
press the AUDIO button until FAD appears on the
display. Press the knob above the AUDIO button to
extend it, then turn the knob to adjust the sound to the
front or rear speakers. The middle position balances the
sound between the speakers.
Press and hold the AUDIO button for at least two
seconds to return all tone settings, including bass
and treble to flat.Using RDS
Your audio system is equipped with a Radio Data
System (RDS). With RDS, the radio can do
the following:

Seek only to stations with the types of programs you
want to listen to,

seek to stations with traffic announcements,

receive announcements concerning local and
national emergencies, and

receive and display messages from radio stations.
RDS features are only available on FM stations that
broadcast RDS information. The RDS features on your
radio rely on receiving specific RDS information from
these stations. These features will only work when the
RDS information is available. In rare cases, a radio
station may broadcast incorrect information that will
cause the radio features to work improperly. If this
happens, contact the radio station.
When you are tuned to an RDS station, the station
name will appear on the display, instead of the
frequency. Most RDS stations provide their station
name, the time of day and a Program Type (PTY)
for their current programming.
ProCarManuals.com

3-14
Finding a PTY Preset Station
To find a PTY preset station, perform the following steps:
1. Press the P
-TYPE button to turn on PTY select. PTY
will be displayed and the light next to the button will
turn on. The last selected PTY will appear on the
display for five seconds.
2. Turn the P
-TYPE knob clockwise or
counterclockwise to select the PTY you want to
listen to. The list is alphabetical. If you select ANY
TYPE your radio will seek to the first PTY available.
3. Press the right SEEK arrow to find radio stations for
that PTY. The radio will seek to the first RDS
broadcaster of the selected program type. If the radio
cannot find the desired program type, NOT FOUND
will appear on the display and the radio will return to
the last station you were listening to. If both P
-TYPE
and TRAF are on, the radio will search for stations
with traffic announcements and the selected PTY.To use the P
-TYPE interrupt feature, press and hold the
P
-TYPE button until you hear a beep on the PTY you
want to interrupt on. An asterisk will appear next to the
PTY name (for example CLASSICAL*). When you are
listening to a cassette or compact disc, the last selected
RDS FM station will interrupt play if that selected PTY
format is broadcast.
BAND (Alternate Frequency): Alternate frequency
allows the radio to switch to a stronger station with the
same program type. Press and hold BAND for two
seconds to turn alternate frequency on. AF ON will
appear on the display. The radio may switch to stronger
stations. Press and hold BAND again for two seconds to
turn alternate frequency off. AF OFF will appear on the
display. The radio will not switch to other stations. When
you turn the ignition off and then on again, the alternate
frequency feature will automatically be turned on.
SEEK : Press the right arrow to go to a station with
the last selected PTY; TYPE and the last selected PTY
will appear on the display, if it is not already showing.
Press SEEK a second time to seek. If a station with the
selected PTY is not found, the radio will return to the
original station and display NONE.
ProCarManuals.com

3-15
Setting PTY Preset Stations
The six numbered pushbuttons let you return to your
favorite Program Types (PTYs). These pushbuttons
have factory PTY presets. You can set up to 12 PTYs
(six FM1 and six FM2) by performing the following steps:
1. Press BAND to select FM1 or FM2.
2. Press the P
-TYPE button to activate program
type mode.
3. Turn the P
-TYPE knob to select a PTY.
4. Press and hold one of the six numbered pushbuttons
until you hear a beep. Whenever you press that
numbered pushbutton, the PTY you set will return.
5. Repeat the steps for each pushbutton.
RDS Messages
ALERT!: This message warns of national or local
emergencies. You will not be able to turn off alert
announcements. ALERT! appears on the display when an
alert announcement plays. When an alert announcement
comes on the current radio station, you will hear it, even if
the volume is muted or a cassette tape or compact disc is
playing. If the cassette tape or compact disc player is
playing, play will stop for the announcement and resume
when the announcement is finished.TRAF (Traffic): Press this button to receive traffic
announcements. The traffic announcement brackets will
appear on the display. TRAF will appear on the display
if the current station broadcasts traffic announcements.
If the current station does not broadcast traffic
announcements, the radio will seek to a station that
does. When the radio finds a station that broadcasts
traffic announcements, it will stop. If no station is found,
NO TRAFFIC will appear on the display.
When a traffic announcement comes on the current radio
station or a related network station, you will hear it, even
if the volume is muted or a cassette tape or compact disc
is playing. If the cassette tape or compact disc player was
being used, the tape or compact disc will stay in the
player and resume play at the point where it stopped.
INFO (Information): If the current station has a
message, INFO will appear on the display. Press this
button to see the message. If the whole message does
not appear on the display, parts of the message will
appear every three seconds until the message is
completed. To see the parts of the message faster than
every three seconds, press this button again. A new group
of words will appear on the display. Once the complete
message has been displayed, INFO will disappear from
the display until another new message is received.
ProCarManuals.com

3-16
Playing a Cassette Tape
Your tape player is built to work best with tapes that are
up to 30 to 45 minutes long on each side. Tapes longer
than that are so thin they may not work well in this
player. The longer side with the tape visible should face
to the right. If the ignition is on, but the radio is off, the
tape can be inserted and will begin playing. If you hear
nothing but a garbled sound, the tape may not be in
squarely. Press the eject (upward pointing arrow) button
to remove the tape and start over.
While the tape is playing, use the VOLUME, POWER,
AUDIO, AUTO EQ, and the SEEK controls just as you
do for the radio. The display will show TAPE and an
arrow showing which side of the tape is playing. The
tape player automatically begins playing the other side
when it reaches the end of the tape.
Your tape bias is set automatically when a metal or
chrome tape is inserted. If you want to insert a tape
when the ignition is off, first press the button with the
eject symbol on it or the RCL knob.
If an error appears on the radio display, the tape won't
play because of an error. See ªCassette Tape Messagesº
later in this section.1 REV (Reverse): Press this pushbutton to reverse
the tape rapidly. Press it again to return to playing speed.
The radio will play the last selected station while the
tape reverses. You may select stations during reverse
operation by using the TUNE knob.
2 FWD (Forward): Press this pushbutton to advance
quickly to another part of the tape. Press this pushbutton
again to return to playing speed. The radio will play the
last selected station while the tape advances. You may
select stations during forward operation by using the
TUNE knob.
3
(Dolby): Press this pushbutton to reduce
background noise. DOLBY ON will appear on the
display with the Dolby symbol. Press it again to turn
Dolby off.
Dolby Noise Reduction is manufactured under a license
from Dolby Laboratories Licensing Corporation. Dolby
and the double
-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
5 SIDE: Press this pushbutton to play the other side
of the tape.
AUTO EQ (Automatic Equalizer): Press AUTO EQ
to select the desired preset equalization setting while
playing a cassette tape. The equalization will be
automatically set whenever you play a cassette tape.
ProCarManuals.com

3-18
WRAPPED: When this message is displayed, the tape
is wrapped around the tape head. Attempt to get the
cassette out. Try a new tape.
CLEAN PLAYR (Clean Player): This message may
also appear on the radio display to indicate that the
cassette tape player needs to be cleaned. It will still play
tapes, but you should clean it as soon as possible to
prevent damage to the tapes and player. For additional
information see ªCare of Your Cassette Tape Playerº in
the Index.
If any error occurs repeatedly or if an error can't be
corrected, contact your dealer. If your radio displays an
error message, write it down and provide it to your
dealer when reporting the problem.
Playing a Compact Disc
With the ignition on, insert a disc partway into the
slot, label side up. The player will pull it in and the disc
should begin playing. If you want to insert a CD when
the ignition is off, first press the eject button or the
RCL knob.When the disc is inserted, the CD symbol will be
displayed. If you select an EQ setting for your CD, it
will be activated each time you play a CD.
As each new track starts to play, the track number will
appear on the display.
If an error appears on the display, see ªCompact Disc
Messagesº later in this section.
1 REV (Reverse): Press and hold this pushbutton to
reverse quickly within a track. You will hear sound at a
reduced volume. Release it to play the passage. The
display will show elapsed time.
2 FWD (Forward): Press and hold this pushbutton to
advance quickly within a track. You will hear sound at a
reduced volume. Release it to play the passage. The
display will show elapsed time.
4 RDM (Random): Press this pushbutton to hear the
tracks in random, rather than sequential, order. RDM
and the track number will appear on the display. Press
this pushbutton again to turn off random mode.
AUTO EQ (Automatic Equalizer): Press this button to
select the desired preset equalization setting while
playing a compact disc. The equalization will be
automatically set whenever you play a compact disc.
ProCarManuals.com