ignition OLDSMOBILE AURORA 2002 Service Manual

2-82 Cruise Light
United States Canada
The CRUISE light comes on whenever you set your
cruise control. See ªCruise Controlº in the Index.
This light will come on for a few seconds when you turn
the ignition key to ON to let you know it is working.
Fuel Gage
United States Canada
When the ignition is on, your fuel gage tells you about
how much fuel you have left.
When you have less than 3.5 gallons (13.2 L) of fuel
remaining, the DIC message LOW FUEL will be
displayed and a chime will sound. You need to get more
fuel right away.
ProCarManuals.com

2-83
Here are four things that some owners ask about. None
of these show a problem with your fuel gage:

At the service station, the gas pump shuts off before
the gage reads full.

It takes a little more or less fuel to fill up than the
gage indicated. For example, the gage may have
indicated the tank was half full, but it actually took
a little more or less than half the tank's capacity to
fill the tank.

The gage moves a little when you turn a corner or
speed up.

The tank is not necessarily empty when the gage
reads empty. There is a reserve of about 1.5 gallons
(5.6 L) in the tank. You should still get more fuel as
soon as possible.Driver Information Center (DIC)
The DIC has different display modes which can be
accessed by pressing the four buttons on the DIC.
These buttons are labeled ON/OFF, SELECT right
arrow, SELECT down arrow and RESET. The button
functions are detailed in the following.
Turn the system on or off by pressing the ON/OFF
button once. When you turn on the ignition, the DIC
will be in the mode last displayed when the engine was
turned off.
ProCarManuals.com

2-85
Elapsed Time (ET)
When the ignition is on, the DIC can be used as a
stopwatch. The display will show hours and minutes.
The elapsed time indicator will record up to 100 hours,
then it will reset to zero and continue counting. Press
SELECT down arrow while in the DATE/ET mode, and
the display will show the amount of time that has
elapsed since the elapsed time indicator was last reset
(not including time the ignition is off), such as:
01:08 ELAPSED TIME
To start or stop the counting of time, press the RESET
button briefly. If the colon (:) in the time is flashing,
time is being counted. Time is displayed in hours and
minutes. Seconds are not displayed. Time will continue
to be counted as long as the ignition is on, even if
another display is being shown on the DIC.
To reset elapsed time to zero, press the RESET button
for three seconds while the elapsed time is displayed.
Fuel
Press the SELECT down arrow while in the FUEL
mode to see how much fuel has been used and the
fuel range functions.Fuel Used
While in the FUEL USED function the display will
show a reading such as:
FUEL USED: 10.4 GAL or FUEL USED: 39.4 L
To learn how much fuel will be used from a specific
starting point, first enter the FUEL USED mode to
display FUEL USED, then press and hold the RESET
button for three seconds.
Don't confuse fuel used with the amount of fuel in
your tank.
Fuel Range
The FUEL RANGE mode calculates the remaining
distance you can drive without refueling. It's based on
fuel economy and the fuel remaining in the tank. The
display will show a reading such as:
FUEL RANGE: 235 MI or FUEL RANGE: 378 KM
If the range is less than 50 miles (80 km), the display
will read LOW FUEL RANGE.
The fuel economy data used to determine fuel range is
an average of recent driving conditions. As your driving
conditions change, this data is gradually updated. Fuel
range cannot be reset.
ProCarManuals.com

2-88 DIC Personalization
The DIC can be used to program the following personal
choice features available with your vehicle:

Automatic Door Locks

Window Lockout

Security Feedback

Delayed Locking

Perimeter Lighting

Driver ID

Memory Seats

Parallel Park Assist Mirror (Tilt Mirror)
To access the personalization menu, the vehicle must be
in PARK (P) with the ignition in ON and no warning
messages displayed on the DIC. You must then press
and hold both of the SELECT buttons for three seconds.
This will display the personalization menu.The DIC display will show the following:
FEATURE PROGRAMMING
PRESS SELECT DOWN TO
SELECT MENU OPTIONS
PRESS SELECT RIGHT TO
CHANGE SETTINGS
The next item to be displayed is DRIVER 1 or
DRIVER 2. To change the driver number, press the
SELECT right arrow. The driver number that you select
should correspond with the number on the back of
your remote keyless entry transmitter. Once the correct
driver number has been selected, press the SELECT
down arrow to enter your choice and move on to the
next selection.
ProCarManuals.com

2-90
If you would like to exit the selection mode without
moving through each of the personal choice features,
simply press a different button on the DIC or turn off
the ignition. The personal choices you made will still be
retained, even without passing through each of the
features. In order for your personal choices to save,
you must press the SELECT down arrow after making
your selections.
If you happen to move past a selection you would like to
make a personal choice for, press unlock on the transmitter
or press the appropriate driver number on the door panel
for the memory seats. This will return you to the
beginning of the optional feature programming mode.
A description of each feature programmable through the
DIC follows.
Automatic Door Locks
You can program the automatic door lock feature to
change to one of the following modes:
Mode 0: No automatic door lock or unlock.
Mode 1: All doors automatically lock when shifted out
of PARK (P). No automatic door unlock.
Mode 2: All doors automatically lock when shifted out
of PARK (P). Only the driver's door automatically
unlocks when shifted into PARK (P).Mode 3: All doors automatically lock when shifted
out of PARK (P). All doors automatically unlock when
shifted into PARK (P).
Mode 4: All doors automatically lock when shifted
out of PARK (P). Only the driver's door automatically
unlocks when the key is turned to OFF.
Mode 5: All doors automatically lock when shifted out
of PARK (P). All doors automatically unlock when the
key is turned to OFF.
You can change the mode your vehicle is in by different
selections of the following DIC displays:

DOORS LOCK IN GEAR
-- YES/NO

DOORS UNLOCK
-- YES/NO

ALL DOORS IN PARK
-- YES/NO

ALL DOORS AT KEY OFF
-- YES/NO

DRIVERS DOOR IN PARK
-- YES/NO

DRIVERS DOOR KEY OFF
-- YES/NO
Press the SELECT right arrow button to toggle between
your choices and change the settings. Press the SELECT
down arrow button to store your changes in memory and
move on to the next selection.
ProCarManuals.com

2-94
The EXT LIGHTS TIMEOUT feature can be changed
to the desired setting by using the SELECT right arrow
button to toggle from 5 to 30 seconds. Each toggle will
increase the time by five seconds. Once the desired
timeout is displayed, press SELECT down arrow to
record your choice and move on to the next personal
choice feature.
For more information on this feature, see ªPerimeter
Lightingº in the Index.
Driver ID
This feature displays the driver ID, as identified by the
DIC. If you choose YES when DISPLAY DRIVER ID
is shown on the DIC, the driver number will be
displayed every time the ignition is turned on. If you
choose NO when DISPLAY DRIVER ID is shown on
the DIC, the driver number can be displayed by pressing
either a button on the remote keyless entry transmitter or
a memory seat button.
Memory Seat Recall (If Equipped)
This feature recalls the position of the driver's seat.
When this feature is active, the memory seat and
mirror positions will be recalled for the identified driver
when the remote keyless entry transmitter is used to
enter the vehicle.You can program this feature to be active by choosing YES
when the KEY FOB MEMORY SEAT choice appears, or
inactive by choosing NO when the KEY FOB MEMORY
SEAT choice appears on the DIC. Make your choices by
pressing the SELECT right arrow button and store them in
memory by pressing the SELECT down arrow button.
You can also program this feature to recall your memory
seat position or the exit seat position. Select YES for
KEY FOB MEMORY SEAT then use the SELECT
right arrow button to toggle between DRIVING
POSITION
- YES and EXIT POSITION - YES.
When the desired position is displayed on the DIC, press
the SELECT down arrow button to save that position in
memory and move on to the next selection.
For more information on this feature, see ªMemory Seat
and Mirrorsº in the Index.
Parallel Park Assist (If Equipped)
The parallel park assist mirror, which tips the passenger
mirror while the vehicle is in REVERSE (R), can be
made active or inactive through the DIC. When TILT
MIRROR REVERSE appears on the display, use the
SELECT right arrow button to toggle the arrow between
YES and NO. When you have made your choice, press
the SELECT down arrow button to record your
selection. For more information on this feature, see
ªMirrorsº in the Index.
ProCarManuals.com

2-96
CHECK OIL LEVEL - 5: If you ever see the
CHECK OIL LEVEL message, it indicates that the
engine oil level is 1 to 1 1/2 quarts (0.9 L to 1.4 L) low.
The message will appear only if the engine is running
and it has been at least eight minutes since the engine
was last running. If the message appears, check the oil
dipstick level. If it reads low, your oil level should be
brought up to the proper level (see ªEngine Oilº in the
Index). After bringing the oil to the proper level, the
ignition must be off for eight minutes to allow the
majority of oil to drain into the oil pan.
SERV STABILITY SYS
- 26: If you ever see the
SERV STABILITY SYS message, it means there may
be a problem with your stability enhancement system. If
you see this message, try to reset the system (stop; turn
off the engine; then start the engine again). If the SERV
STABILITY SYS message still comes on, it means there
is a problem. You should see your dealer for service.
Reduce your speed and drive accordingly.STABILITY ACTIVE
- 42: You may see the
STABILITY ACTIVE message on the Driver
Information Center. It means that an advanced,
computer
-controlled system has come on to help your
vehicle continue to go in the direction in which you're
steering. This stability enhancement system activates
when the computer senses that your vehicle is just
starting to spin, as it might if you hit a patch of ice or
other slippery spot on the road. When the system is on,
you may hear a noise or feel a vibration in the brake
pedal. This is normal.
When the STABILITY ACTIVE message is on, you
should continue to steer in the direction you want to go.
The system is designed to help you in bad weather or
other difficult driving situations by making the most of
whatever road conditions will permit. If the STABILITY
ACTIVE message comes on, you'll know that
something has caused your vehicle to start to spin, so
you should consider slowing down.
ProCarManuals.com

3-4
(Air Conditioning): Press this button to turn
the air conditioning compressor on and off. The air
conditioning indicator light will illuminate. In the
automatic mode, the air conditioning compressor will
only operate when the system determines it is needed.
(Recirculation): Press this button to limit the
amount of outside air entering your vehicle. This is
helpful when you are trying to cool the interior of the
vehicle quickly or limit the amount of outside air
entering your vehicle for some other reason. The
recirculation button may be selected and the mode knobs
may be adjusted at the same time. The system will
remain in recirculation until the ignition is turned off,
then the system will return to the previously selected
mode. Recirculation may be selected in all airflow
modes except defrost.
When the weather is cool or damp, operating in
recirculation for extended periods of time may cause
fogging of the vehicle's windows. To clear the fog,
switch back to outside air by turning off recirculation,
then select either defogger or defrost mode and increase
the fan speed. To avoid refogging of the windows,
minimize your use of recirculation under these
conditions and turn the air conditioning on to help
dehumidify the air.Automatic Operation
Press the left and right mode knobs for the system
to automatically maintain the air temperature, airflow
direction and the fan speed. They will be controlled based
on the selected temperature setting, the temperature inside
the vehicle, the outside temperature and the sun load.
Fan speed will vary as the system reaches and maintains
the comfort setting you have selected.

Press the left and right mode knobs to turn on
the lights under the knobs, indicating that the
system is being controlled automatically. Your
current temperature setting will be shown in the
digital display.

Then adjust the temperature level using the red
and blue arrows located below the climate control
display until you reach a setting of 75F (24C)
on the display. Give the vehicle about 30 minutes to
stabilize and then readjust the temperature setting if
necessary. The display will show the temperature
setting for five seconds and then it will show the
outside temperature.
ProCarManuals.com

3-6 Comfort Controls Personalization
(If Equipped)
This feature enables up to two drivers to store and recall
comfort control settings for temperature, air delivery
mode and fan speed.
The memory buttons (1 or 2) for this feature are located
on the driver's door panel and correspond to the
numbers (1 or 2) found on the back of each remote
keyless entry transmitter.
To recall comfort settings, press the unlock button
on the remote keyless entry transmitter and put the
ignition in ACC (Accessory) or ON. The climate
control setting last chosen by the identified
driver (1 or 2) will be recalled.
To program a personal climate control setting, do
the following:
1. Choose a climate control setting for the driver
and if desired, for the passenger. See ªAutomatic
Electronic Climate Controlº and ªPassenger
Temperature Control (Option)º earlier in this section.
2. Adjust the direction of the airflow.3. Locate the memory buttons on the driver's
door panel.
4. Press a memory button (1 or 2) until you hear two
beeps. The beeps confirm that your selection has
been saved and can now be recalled.
Follow these steps each time you want to change the
stored settings. For more information on the memory
feature, see ªMemory Seat and Mirrorsº in the Index.
Air Conditioning
The air conditioner cools and dehumidifies the air inside
of the vehicle.
The air conditioning compressor is enabled in all
modes unless the air conditioning button is not selected
(the indicator light will not be illuminated). However,
the air conditioning compressor will not operate when
the outside temperature is below 34
F (1
C). When the
air conditioner is on, you may sometimes notice slight
changes in your vehicle's engine speed and power. This
is normal, because the system is designed to cycle the
compressor on and off to maintain the desired
temperature and to help with fuel economy.
ProCarManuals.com

3-8 Rear Window Defogger
(Rear Defogger):
Press this button to
warm the defogger
grid on the rear
window. An indicator
light below the button
will glow while the
rear window defogger
is operating.
At speeds above 30 mph (48 km/h), the rear defogger
will stay on until you press the rear button again. At
speeds below 30 mph (48 km/h), the rear defogger will
turn off automatically after about 10 minutes of use. If
you press it again, the defogger will operate for about
five minutes only. You can also turn the defogger off
by turning off the ignition.
Do not attach a temporary vehicle license across the
defogger grid on the rear window.
If your vehicle is equipped with heated outside rearview
mirrors, when you operate the rear window defogger,
the mirrors are also heated to help remove ice and fog.
For more information see ªHeated Outside Rearview
Mirrorsº in the Index.
NOTICE:
Don't use a razor blade or other sharp object on
the inside of the rear window. If you do, you
could cut or damage the warming grid, and the
repairs wouldn't be covered by your warranty.
Ventilation System
Your vehicle's flow-through ventilation system allows
filtered outside air to flow through your vehicle while it
is moving, even if the system is off.
The direction of the airflow
can be controlled by
adjusting/closing the outlets
in the instrument panel.
ProCarManuals.com