height Oldsmobile Cutlass Supreme 1994 Owner's Manuals

Features & Controls
100
~.*.,. :.. ~~.,,~..~.,.~. ;,~,!~~. ~~~~....,...... :.~:~........:.*,:~
.r..,..,~.~...:.1/2~~:1~.~.,~::,:.-..~~.':,lr'\..:.'..,,iC.~..;.~'...;:\
...::..:.: ...., 4; ...,., :*-&
2. Adjust the seat, if necessary, before
setting the height control.
Rotate the HUD image height control
all the way
up, raising the image as
far as possible. Then rotate the HUD
image height control downward
so
the image is as low as possible but in
full view.
3. Slide the dimmer control toward
OFF until the HUD image is no
brighter than necessary.
To turn the
HUD
off, slide the HUD dimmer
control to
OFF.
If the sun comes out, or it becomes
cloudy, or
if you turn on your
headlights. vou mav need to adiust the HUD's
brightness using the HUD
dimmer control. Polarizing sunglasses
could make the HUD image harder
to see.
Irr .
Pushing the ENG/MET rocker switch
on the center console will switch the
HUD speedometer from English
(conventional) to metric units, or back
again.
Some vehicles may not be equipped
with the
ENG/MET switch.

Care of the Head-Up Display
Clean the inside of the windshield as
needed to remove any dirt or film that
reduces the sharpness or clarity of the
HUD image.
To Clean the HUD:
Spray household glass cleaner on a soft,
clean cloth. Wipe the HUD lens gently,
then
dry it. Do not spray cleaner
directly on the lens, because the cleaner
fluid could leak inside the unit
if you do.
If You Can’t See the HUD Image
When the Ignition
is On:
Is anything covering the HUD unit?
Is the HUD dimmer control close
Is the HUD image adjusted to the
enough
to
MAX?
proper height?
Still no HUD image? Check the fuse
in the
CLSTR position in the glove
box fuse panel. See the Index under
Fuses G Circuit Breakers.
If the HUD Image is Not Clear:
It could be too bright. Move the HUD
dimmer control closer
to OFF.
You may need to clean the windshield
and HUD lens.
Your windshield is part of the HUD
system. If you ever have to have
a new
windshield, be sure to get one designed
for HUD. If you don’t, the HUD image
may look blurred and out of focus.

sound may come and go or be heard all
the time your vehicle is moving (except
when you are pushing
on. the brake
pedal firmly).
NOTICE:
Continuing to drive with worn-out
brake pads could result in costly
brake repair.
Some driving conditions or climates
may cause a brake squeal when the
brakes are first applied or lightly
applied. This does not mean something
is wrong with your brakes.
Brake linings should always be replaced
as complete axle sets.
Brake Pedal Travel-
See your dealer if the brake pedal does
not return to normal height, or if there
is a rapid increase in pedal travel. This
could be a sign
of brake trouble.
Brake Adjustment
Every time you male a moderate brake
stop, your disc brakes adjust for wear. If
you rarely make a mo.derate or heavier
stop, then your brakes might not adjust
correctly.
If you drive in that way, then
- very carefully - make a few
moderate brake stops about every
1,000
miles (1 600 km) , so your brakes will
adjust properly.
Replacing Brake System Parts
The braking system on a modern
vehicle is complex. Its many parts have
to be of top quality and work well
together
if the vehicle is to have really
good braking. Vehicles we design and
test have top-quality
GM brake parts in
them, as your Oldsmobile does when it
is new. When you replace parts of your
braking system
- for example, when
your brake linings wear down and you have
to have new ones put in
- be sure
you get new genuine
GM replacement
parts.
If you don’t, your brakes may no
longer work properly. For example, if
someone puts.in brake linings that are
wrong for your vehicle, the balance
between your front and rear brakes can
change, for the worse; The braking
performance you’ve come to expect can
change in many other ways if someone
puts in the wrong replacement brake
parts.
195