suspension Oldsmobile Cutlass Supreme 1994 Owner's Manuals

NOTICE:
Towing a vehicle over rough
surfaces could damage
a vehicle.
Damage can occur
from vehicle to
ground or vehicle to wheel-lift
equipment.
To help avoid damage,
install a towing dolly and raise
vehicle until adequate clearance is
obtained between the ground
and/or wheel-lift equipment.
Do not attach winch cables or
J-
hooks to suspension components
when using car carrier equipment.
Always use T-hooks inserted in the
T-hook slots.
AN Models
3. Attach a separate safety chain around
the outboard end
of each lower
control arm.
157

Maintenance Schedule
242 ~
Explanation of~scheduled
Mainfenance Services
Following are explanations of the
services listed in Schedule I and
Schedule
11.
The proper fluids and lubricants to use
are listed in Section D. Make sure
whoever services your vehicle
uses
these. All parts should be-replaced and
all necessary repairs done before you or
anyone else drives the vehicle.
ITEM SERVICE
NO.
1. Engine Oil and Filter Change* -
Always use SH or SG Energy
Conserving I1 oils of proper viscosity.
The “SH” or “SG” designation may
be shown alone or in combination
with others, such as “SH/CD,” “SH,
SG, CD,”“SG/CD,” etc. To
determine the preferred viscosity for
your vehicle’s engine (e.g., SAE 5W-
30 or SAE 10W-30), see
Engine Oil
in the Index.
2. Chassis Lubrication - Lubricate
suspension and steering linkage.
Lubricate the transaxle shift linkage,
and parking brake cable guides,
underbody contact points and
linkage.
3. Tire and Wheel Rotation and
Inspection
- For proper wear and
maximum tire life, rotate your tires
following the instructions in this
manual. See
Tires, Inspection 6
Rotation in the hdex. Check the
tires for uneven wear or damage.
If
you see irregular or premature wear,
check the wheel alignment. Check for
damaged wheels also.
Inspection *‘ - Inspect the belt for
cracks, fraying, wear and proper
tension. Replace as needed.
5. Camshaft Timing Belt Inspection
(3.4L Code X engine only) * -
Inspect for cracks, wear or oiliness.
Check tensioner for proper operation.
See the service manual.
(To purchase
4. Engine Accessory Drive Belt
a service manual, see Service
Publications
in the Index.) Replace
parts as needed.
6. Cooling System Service* - Drain,
flush and refill the system with new
or approved recycled. coolant
conforming
to GM Specification
1825M. Keep coolant at the proper
mixture as specified. See
Coolant in
the
Index. This provides proper
freeze and boil protection, corrosion
inhibitor level and maintains proper
engine operating temperature.
Inspect hoses and replace
if they are
cracked, swollen or deteriorated.
Clean the outside of the radiator and
air conditioning condenser. Wash the
pressure cap and neck.
To help ensure proper operation, we
recommend a pressure test of both
the cooling system and the pressure
cap.
7. Transaxle Service - Change both
the fluid and filter .every
15,000 miles
(25
000 lm) if the vehicle is mainly

Section C: Periodic Maintenance Inspections
Listed below are inspections and services which should be performed at least twice a year (for instance, each spring and fall).
You should let your GM dealer’s service department or other qualified service center
do these jobs. Make sure any necessary
Bepairs are completed at once.
INSPECTION
OR SERVICE
Restraint Systems
Steering, Suspension
and FrontWheel-
Drive Axle Boot and
Seal Inspection
Exhaust System
Inspection
Throttle Linkage
Inspection
Brake System Inspection
WHAT SHOULD BE DONE
Now and then, make sure all your belts, buckles, latch plates, retractors, anchorages and
reminder systems are working properly. Look for any loose parts or damage.
If you see anything
that might keep a restraint system from doing its job, have it repaired.
Inspect the front and rear suspension and steering system for damaged, loose or missing parts,
signs of wear, or lack
of lubrication. Inspect the power steering lines and hoses for proper
hookup, binding, leaks, cracks, chafing, etc. Clean and then inspect the drive axle boot seals for
damage, tears or leakage. Replace seals if necessary.
Inspect the complete exhaust system. Inspect the body near the exhaust system. Look for broken,
damaged, missing or out-of-position parts as well as open seams, holes, loose connections, or
other conditions which could cause a heat build-up in the floor pan or could let exhaust fumes
into the vehicle. See
Engine Exhaust in the Index.
.. -
Inspect the throttle linkage for interference or binding, and for damaged or missing parts.
-Replace parts as needed.
Inspect the complete system. Inspect brake lines and hoses for proper hookup, binding, leaks, cracks,
chafing, etc. Inspect disc brake pads for wear and rotors for surface condition. Inspect other bralte
parts, including calipers, parking brake, etc. Check parking bralte adj\
ustment. You may need to have
your brakes inspected more often
if your driving habits or conditions result in frequent braking.
NOTE:-A low brake fluid level can indicate worn disc brake pads which may need to be serviced.
Also,
if the bralte system warning light stays on or comes on, something may be wrong with the
brake system. See
Brake System Warning Light in the Index. If your vehicle is equipped with anti-
lock brakes and the anti-lock bralte system warning
light stays on, comes on or flashes, something
may be wrong with the anti-lock brake system. See
Anti-Lock Brake System Warning Light in the Index.
247