OLDSMOBILE INTRIGUE 1998 Owners Manual

Turn SignaVMultifunction Lever
The lever on the left side of the steering column
includes your:
Turn Signal and Lane Change Indicator
Headlamp High/Low Beam Changer
Headlamps
Taillamps
0 Parking Lamps
nrn Signal and Lane Change Indicator
The turn signal lever has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn or lane change.
To signal a turn, move the lever
all the way up or
down. When the turn is finished, the lever will
return automatically.
11 An arrow on the instrument
1
A panel will flash in the
direction of the
turn or
lane change.
2-31
ProCarManuals.com

To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by
itself when you release it.
As you signal a turn or lane change, if the arrow flashes
faster than normal, a signal bulb may be burned out and
other drivers won’t see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident.
If the arrows don’t go on at all when you
signal a turn, check for burned-out bulbs and then check
the fuse (see “Fuses and Circuit Breakers” in the Index).
A chime will sound if you leave your turn signal on for
more than
3/4 mile (1.2 km).
Headlamp High/Low Beam Changer
To change your headlamps
from low beam
to high
beam, push the lever
forward.
To change back to
low beam, pull the lever
toward you.
To flash your high beams, pull the lever toward you and
release. The lever will return to the low-beam position.
Flash-to-Pass
With the lever in the low-beam position, pull the lever
toward you momentarily to switch to high beams
(to
signal you are going to pass). If you have the headlamps
on, they will return
to low beams when you release
the lever.
2-32
ProCarManuals.com

Windshield Wipers
You can control the windshield wipers by turning the
band with the wiper symbol on it. This lever is located
on the right-hand side of the steering wheel. For
a single wiping cycle, turn the band to MIST. Hold
it there until the wipers start, then let go. the wipers will
stop after one cycle. If you want more cycles, hold the
band on MIST longer.
You can set the wiper speed for a long delay or short
delay between wipes. This can be very useful in light
rain or snow. Push the lever up to INT (intermittent),
then turn the band, located on the lever,
to adjust the
delay time. Rotate the band down for a longer delay,
up
for a shorter delay. The wiper speed can only be
adjusted when the lever is in INT position, not in HI
or
LO.
Be sure to clear the ice and snow from the wiper blades
before using them.
If they’re frozen to the windshield,
carefully loosen or thaw them.
If your blades do become
damaged, get new blades or blade inserts.
Heavy snow or ice can overload your wipers.
A circuit
breaker will
stop them until the motor cools. Clear away
snow or ice to prevent an overload.
2-33
ProCarManuals.com

Windshield Washer At the end of the right-hand lever on the steering wheel,
there
is a wiper symbol. To spray washer fluid on the
windshield, push the button
on the end of the lever. The
wipers will run
for several sweeps and then either stop
or return to your preset speed.
I-
CAUTION:
In freezing weather, don’t use your washer until
the windshield is warmed. Otherwise the washer
fluid can form ice on the windshield, blocking
your vision.
2-34
ProCarManuals.com

Cruise Control
With cruise control, you can maintain a speed of about
25 mph (40 km/h) or more without keeping your foot on
the accelerator. This can really help on long trips. Cruise
control does not work at speeds below about
25 mph
(40 km/h).
When you apply your brakes, the cruise control
shuts
off.
A CAU‘ [ON:
I
Setting Cruise Control
Cruise control can be dangerous where you
can’t drive safely
at a steady speed. So,
don’t use your cruise control on winding
roads or in heavy traffic.
slippery roads. On such roads, fast changes
in tire traction can cause needless wheel
spinning, and you could lose control. Don’t
use cruise control on slippery roads.
Cruise control can be dangerous on
If you leave your cruise control switch on when
you’re not using cruise, you might hit
a button
and go into cruise when you don’t want to. You
could be startled and even lose control. Keep the
cruise control switch off until you want to use it.
I I
1. Push the cruise control
button on the instrument
panel to turn it on.
2. Get up to the speed you want.
2-35
ProCarManuals.com

3. Push the COAST/SET
button on your steering wheel and release it. Once
you’re going about
25 rnph (40 km/h)or more,
press the RES/ACCEL
button on your steering
wheel. You’ll go right back
up to your chosen speed and
stay there.
4. Take your foot off the accelerator.
The CRUISE light on the instrument panel cluster will
come on after the cruise control has been set to the
desired speed.
It will go off when you:
step lightly on the brake pedal,
0 press CLEAR on the steering wheel or
0 press the CRUISE button on the instrument panel.
Resuming a Set Speed
Suppose you set your cruise control at a desired speed
and then you apply the brake. This, of course shuts off
the cruise control. But you don’t need to reset
it.
Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed:
0
0
Use the accelerator pedal to get to the higher speed.
Press the COAST/SET button on the steering wheel,
then release the button and the accelerator pedal.
You’ll now cruise at the higher speed.
Press the RES/ACCEL button on the steering wheel.
Hold it there until you get up to the speed you want
and then release the switch. (To increase your speed
in very small amounts, press the RES/ACCEL
button for less than half a second and then release it.
Each time you do this, your vehicle will
go 1 mph
(1.6 km/h) faster.)
2-36
ProCarManuals.com

The accelerate feature will only work after you set the
cruise control speed by pressing the COAST/SET button
on the steering wheel.
Reducing Speed While Using Cruise Control
There are two ways to reduce your speed while using
cruise control:
Press the COAST/SET button on the steering wheel
until
you reach the lower speed you want, then
release it.
To slow down in very small amounts, press the
COASTBET button on the steering wheel for less
than a half second. Each time you do this, you’ll go
1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot
off the pedal, your vehicle will slow
down to the cruise speed you set earlier.
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear
to keep your speed down. Of course, applying the brake
takes you out
of cruise control. Many drivers find this to
be too much trouble and don’t use cruise control on
steep hills.
Ending Cruise Control
There are three ways to cancel the cruise control:
0 Step lightly on the brake pedal,
0 Press CLEAR on the steering wheel or
Press the CRUISE button on the instrument panel.
Erasing Cruise Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.
ProCarManuals.com

Exterior Lamps
The lamp controls are located on the multifunction
lever on the left
of the steering wheel. They control
these systems:
Headlamps
Taillamps
Parking Lamps
License Lamps
0 Sidemarker Lamps
0 Instrument Panel Lights
Turn the end of the lever to this symbol to turn on
the headlamps and other operating lamps.
zoo=
- Turn the end of the lever to this symbol to turn
on the parking and other operating lamps without the
headlamps.
Turn the end of the lever to
OFF to turn off the lamps.
A warning chime will sound if you open the driver’s
door when you turn the ignition switch to
OFF or ACC
with the lamps on.
2-38
ProCarManuals.com

Daytime Running Lamps / Automatic
Headlamp Control
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful in the
short periods after dawn and before sunset.
A light sensor on top of the instrument panel makes the
DRL work, so be sure it isn’t covered.
The DRL system will make your front turn signal lamps
come on when:
The ignition is on,
0 The headlamp switch is off and
0 The parking brake is released.
When the
DRL are on, only your front turn signal lamps
will be on.
The headlamps, taillamps, sidemarker and
other lamps won’t be on. Your instrument panel won’t
be lit up either.
When it’s dark enough outside, your front turn signal
lamps will turn off and your headlamps and parking
lamps will turn on.
When it’s bright enough outside, your headlamps will
go
off and your front turn signal lamps will come on.
To idle your vehicle with the DRL off, set the parking
brake while the ignition is in
OFF. Then start your
vehicle. The DRL, headlamps and parking lamps will
stay off until
you release the parking brake.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
Fog Lamps
To turn the fog lamps on,
press the fog lamp switch.
A light will glow on the
switch
to let you know that
they are on. (Your parking
lamps must be on, or your
fog lamps won’t come on.)
Press the switch again to
turn the fog lamps off.
The fog lamps will go
off whenever you change to
high-beam headlamps. When you return to low beams,
the fog lamps will come on again.
2-39
ProCarManuals.com

Interior Lamps Illuminated Entry
Your courtesy lamps will come on and stay on for a set
time whenever you press UNLOCK on the remote
keyless entry transmitter (if equipped).
If you open a door, the lamps will stay on while it’s open
then turn off automatically about
25 seconds after you
close it.
If you press UNLOCK and don’t open a door,
the lamps will turn off after about
40 seconds.
Instrument Panel Brightness Control
You can brighten or dim the
instrument panel lights by
moving the interior lamps
dial. Turn the dial up
to
increase the brightness of
the instrument panel lights.
Turn the dial down to
decrease the brightness.
Courtesy Lamps
When any door is opened, several lamps come on. These
lamps
are courtesy lamps. They make it easy for you to
enter and leave your vehicle.
You can also turn these
lamps
on by turning the interior lamps dial all the
way up. Illuminated entry includes
a feature called
theater
dimming. With theater dimming, the lamps don’t just
turn off at the end of the delay time. Instead, they slowly
dim after the delay time until they
go out. The delay
time is canceled
if you turn the ignition key to ON, so
the lamps will dim out right away. When the ignition is
on, illuminated entry is inactive, which means the
courtesy lamps won’t come on unless a door is opened.
2-40
ProCarManuals.com