ad blue OLDSMOBILE INTRIGUE 1999 Owners Manual

yellowblue
2-31
Tilt Wheel
A tilt wheel allows you to adjust the steering wheel
before you drive. You can also raise it to the highest
level to give your legs more room when you exit and
enter the vehicle.
To tilt the wheel, hold the wheel and pull the lever
located on the left side of your steering column. Move
the wheel to a comfortable level, then release the lever
to lock the wheel in place.
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes your:

Turn Signal and Lane Change Indicator

Headlamp High/Low
-Beam Changer

Flash
-to-Pass

Headlamps

Taillamps

Parking Lamps
ProCarManuals.com

yellowblue
2-32 Turn Signal and Lane Change Indicator
The turn signal lever has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn or lane change.
To signal a turn, move the lever all the way up or down.
When the turn is finished, the lever will return automatically.
An arrow on the instrument
panel will flash in the
direction of the turn or
lane change.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by
itself when you release it.
As you signal a turn or lane change, if the arrow flashes
faster than normal, a signal bulb may be burned out and
other drivers won't see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don't go on at all when you
signal a turn, check for burned
-out bulbs and then check
the fuse (see ªFuses and Circuit Breakersº in the Index).A chime will sound if you leave your turn signal on for
more than 3/4 mile (1.2 km).
Headlamp High/Low-Beam Changer
To change your headlamps
from low beam to high
beam, push the lever away
from you. To change back
to low beam, pull the lever
toward you.
To flash your high beams, pull the lever toward you and
release. The lever will return to the low
-beam position.
Flash-to-Pass
With the lever in the low-beam position, pull the lever
toward you momentarily to switch to high beams (to
signal you are going to pass). If you have the headlamps
on, they will return to low beams when you release
the lever.
ProCarManuals.com

yellowblue
2-33 Windshield Wipers
You can control the windshield wipers by moving the
lever with the wiper symbol on it up or down. This lever
is located on the right side of the steering wheel.
For a single wiping cycle, pull down on the band to
MIST. Hold it there until the wipers start, then let go.
The wipers will stop after one cycle. If you want more
cycles, hold the band on MIST longer.You can set the wiper speed for a long delay or short
delay between wipes. This can be very useful in light
rain or snow. Push the lever up one click to INT
(intermittent), then turn the band, located on the lever, to
adjust the delay time. Turn the band down for a longer
delay, up for a shorter delay. The wiper speed can only
be adjusted when the lever is in the INT position, not in
HI or LO.
Be sure to clear the ice and snow from the wiper blades
before using them. If they're frozen to the windshield,
carefully loosen or thaw them. If your blades do become
damaged, get new blades or blade inserts.
Heavy snow or ice can overload your wipers. A circuit
breaker will stop them until the motor cools. Clear away
snow or ice to prevent an overload.
ProCarManuals.com

yellowblue
2-34 Windshield Washer
At the end of the right-hand lever on the steering wheel,
there is a wiper symbol. To spray washer fluid on the
windshield, push the button on the end of the lever. The
wipers will run for several sweeps and then either stop
or return to your preset speed.
CAUTION:
In freezing weather, don't use your washer until
the windshield is warmed. Otherwise the washer
fluid can form ice on the windshield, blocking
your vision.
Cruise Control
With cruise control, you can maintain a speed of about
25 mph (40 km/h) or more without keeping your foot on
the accelerator. This can really help on long trips.
Cruise control does not work at speeds below about
25 mph (40 km/h).
When you apply your brakes, the cruise control
shuts off.
CAUTION:

Cruise control can be dangerous where you
can't drive safely at a steady speed. So,
don't use your cruise control on winding
roads or in heavy traffic.

Cruise control can be dangerous on
slippery roads. On such roads, fast changes
in tire traction can cause needless wheel
spinning, and you could lose control. Don't
use cruise control on slippery roads.
If your vehicle is in cruise control when the traction
control system (optional with the 3.5L V6 engine) or
enhanced traction system (3800 V6 engine) begins to
limit wheel spin, the cruise control will automatically
disengage. (See ªTraction Control Systemº or
ªEnhanced Traction Systemº in the Index.) When road
conditions allow you to safely use it again, you may turn
the cruise control back on.
ProCarManuals.com

yellowblue
2-35
Setting Cruise Control
CAUTION:
If you leave your cruise control switch on when
you're not using cruise, you might hit a button
and go into cruise when you don't want to. You
could be startled and even lose control. Keep the
cruise control switch off until you want to use it.
1. Press the CRUISE
button on the right side
of the instrument panel
to turn it on. A light on
the button will indicate
that the system is on.
2. Get up to the speed you want.
3. Press the COAST SET
button on your steering
wheel and release it.
4. Take your foot off the accelerator.
The CRUISE light on the instrument panel cluster will
come on after the cruise control has been set to the
desired speed. It will go off when you:

step lightly on the brake pedal,

press CLEAR on the steering wheel or

press the CRUISE button on the instrument panel.
ProCarManuals.com

yellowblue
2-36
Resuming a Set Speed
Suppose you set your cruise control at a desired speed
and then you apply the brake. This, of course shuts off
the cruise control. But you don't need to reset it.
Once you're going about
25 mph (40 km/h) or more,
press the RES ACCEL
button on your steering
wheel. You'll go right back
up to your chosen speed and
stay there.
Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed:

Use the accelerator pedal to get to the higher speed.
Press the COAST SET button on the steering wheel,
then release the button and the accelerator pedal.
You'll now cruise at the higher speed.
Press the RES ACCEL button on the steering wheel.
Hold it there until you get up to the speed you want
and then release the button. (To increase your speed
in very small amounts, press the RES ACCEL button
for less than half a second and then release it.
Each time you do this, your vehicle will go
1 mph (1.6 km/h) faster.)
The accelerate feature will only work after you set the
cruise control speed by pressing the COAST SET button
on the steering wheel.
Reducing Speed While Using Cruise Control
There are two ways to reduce your speed while using
cruise control:

Press the COAST SET button on the steering wheel
until you reach the lower speed you want, then
release it.

To slow down in very small amounts, press the
COAST SET button on the steering wheel for less
than a half second. Each time you do this, you'll go
1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot off the pedal, your vehicle will slow
down to the cruise speed you set earlier.
ProCarManuals.com

yellowblue
2-37
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear
to keep your speed down. Of course, applying the brake
takes you out of cruise control. Many drivers find this to
be too much trouble and don't use cruise control on
steep hills.
Ending Cruise Control
There are three ways to cancel the cruise control:

Step lightly on the brake pedal,

Press CLEAR on the steering wheel or

Press the CRUISE button on the instrument panel.
Erasing Cruise Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.Exterior Lamps
The lamp controls are located on the multifunction
lever on the left of the steering wheel. They control
these systems:

Headlamps

Taillamps

Parking Lamps

License Lamps

Sidemarker Lamps

Instrument Panel Lights
Turn the end of the lever to this symbol to turn on
the headlamps and other operating lamps.
Turn the end of the lever to this symbol to turn
on the parking and other operating lamps without
the headlamps.
Turn the end of the lever to OFF to turn off the lamps.
A warning chime will sound if you open the driver's
door when you turn the ignition switch to OFF or ACC
with the lamps on.
ProCarManuals.com

yellowblue
2-38 Daytime Running Lamps / Automatic
Headlamp Control
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful in the
short periods after dawn and before sunset.
A light sensor on top of the instrument panel makes the
DRL work, so be sure it isn't covered.
The DRL system will make your front turn signal lamps
come on when:

the ignition is on,

the headlamp switch is off and

the parking brake is released.
When the DRL are on, only your front turn signal lamps
will be on. The headlamps, taillamps, sidemarker and
other lamps won't be on. Your instrument panel won't
be lit up either.
When it's dark enough outside, your front turn signal
lamps will turn off and your headlamps and parking
lamps will turn on.When it's bright enough outside, your headlamps will go
off and your front turn signal lamps will come on.
To idle your vehicle with the DRL off, set the parking
brake while the ignition is in OFF. Then start your
vehicle. The DRL, headlamps and parking lamps will
stay off until you release the parking brake.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
Fog Lamps
To turn the fog lamps on,
press the fog lamp switch
on the left side of the
instrument panel.
ProCarManuals.com

yellowblue
2-39
A light will glow on the switch to let you know that they
are on. (Your parking lamps must be on, or your fog
lamps won't come on.) Press the switch again to turn the
fog lamps off.
The fog lamps will go off whenever you change to
high
-beam headlamps. When you return to low beams,
the fog lamps will come on again.
Interior Lamps
Instrument Panel Brightness Control
You can brighten or dim the
instrument panel lights by
turning the interior
lamps dial.
Turn the dial up to increase the brightness of the
instrument panel lights. Turn the dial down to decrease
the brightness.
Courtesy Lamps
When any door is opened, several lamps come on. These
lamps are courtesy lamps. They make it easy for you to
enter and leave your vehicle. You can also turn these
lamps on by turning the interior lamps dial all the
way up or by each individual lamp.
Illuminated Entry
Your courtesy lamps will come on and stay on for a set
time whenever you press UNLOCK on the remote
keyless entry transmitter (if equipped).
If you open a door, the lamps will stay on while it's open
then turn off automatically about 25 seconds after you
close it. If you press UNLOCK and don't open a door,
the lamps will turn off after about 40 seconds.
Illuminated entry includes a feature called theater
dimming. With theater dimming, the lamps don't just
turn off at the end of the delay time. Instead, they slowly
dim after the delay time until they go out. The delay
time is cancelled if you turn the ignition key to ON, so
the lamps will dim out right away. When the ignition is
on, illuminated entry is inactive, which means the
courtesy lamps won't come on unless a door is opened.
ProCarManuals.com

yellowblue
2-40 Illumination on Door Handle Activation
Illumination on Door Handle Activation is a standard
feature intended to provide enhanced security and
convenience by allowing the driver to activate the
vehicle interior illumination without unlocking or
opening any vehicle door.
The ignition must be off and the doors locked for the
Illumination on Door Handle Activation to work. The
Illumination on Door Handle Activation feature can
function in two ways.
If the driver pulls and releases any front door
handle within one second, the interior lamps will
illuminate until:

The ignition is turned to ON,

The power door locks are activated or

An illumination period of 25 seconds has elapsed.
Or, if the driver pulls and holds any front door handle
for more than one second, the interior lamps will
illuminate until:

The ignition is turned to ON,

The door handle is released or

An illumination period of 50 seconds has elapsed.If during the illumination period a door is opened, the
timed illumination period will be cancelled, though the
interior lamps will remain on since the vehicle door
is open.
Delayed Illumination
The Delayed Illumination feature will continue to
illuminate the interior for 25 seconds after all doors have
been closed so that you can find the ignition and buckle
your seat belt at night. Delayed Illumination will not
occur while the ignition is in ON. After 25 seconds have
elapsed, the interior lamps will slowly fade out. The
lamps will fade out before 25 seconds have elapsed
if you:

Turn the ignition to ON.

Lock all doors using your remote keyless entry
transmitter (optional).

Lock the doors using the power door lock switch.
If during the Delayed Illumination period a door is
opened, the timed illumination period will be cancelled,
though the interior lamps will remain on since the door
is opened.
ProCarManuals.com