wheel OLDSMOBILE INTRIGUE 1999 User Guide

yellowblue
2-24
FIRST (1): This position gives you even more power
(but lower fuel economy) than SECOND (2). You can
use it on very steep hills, or in deep snow or mud. If the
shift lever is put in FIRST (1), the transaxle won't shift
into first gear until the vehicle is going slowly enough.
NOTICE:
If your front wheels can't rotate, don't try to
drive. This might happen if you were stuck in
very deep sand or mud or were up against a solid
object. You could damage your transaxle. Also, if
you stop when going uphill, don't hold your
vehicle there with only the accelerator pedal. This
could overheat and damage the transaxle. Use
your brakes or shift into PARK (P) to hold your
vehicle in position on a hill.
Parking Brake
To set the parking brake,
hold the regular brake pedal
down with your right foot.
Push down the parking
brake pedal with your
left foot.
To release the parking brake, hold the regular brake
pedal down with your right foot and push the parking
brake pedal with your left foot. When you lift your left
foot, the parking brake pedal will follow it to the
released position.
ProCarManuals.com

yellowblue
2-30
Windows
Power Windows
Switches on the driver's door armrest control each of the
windows when the ignition is on. In addition, each
passenger door has a switch for its own window.
The driver's window switch has an auto
-down feature.
This switch is labeled AUTO. Tap the switch rearward,
and the driver's window will open a small amount. If the
switch is moved all the way back, the window will go all
the way down.To stop the window while it is lowering, press the
switch. To raise the window, press and hold the
switch forward.
The driver's window
controls also include a
lock
-out switch. Press
LOCK to stop front and rear
passengers from using their
window switches.
The driver can still control all windows with the lock on.
Press the other side of the LOCK switch for normal
window operation.
Full Floating Horn
The full floating horn is designed so that you may press
anywhere on the steering wheel pad to sound the horn.
ProCarManuals.com

yellowblue
2-31
Tilt Wheel
A tilt wheel allows you to adjust the steering wheel
before you drive. You can also raise it to the highest
level to give your legs more room when you exit and
enter the vehicle.
To tilt the wheel, hold the wheel and pull the lever
located on the left side of your steering column. Move
the wheel to a comfortable level, then release the lever
to lock the wheel in place.
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes your:

Turn Signal and Lane Change Indicator

Headlamp High/Low
-Beam Changer

Flash
-to-Pass

Headlamps

Taillamps

Parking Lamps
ProCarManuals.com

yellowblue
2-33 Windshield Wipers
You can control the windshield wipers by moving the
lever with the wiper symbol on it up or down. This lever
is located on the right side of the steering wheel.
For a single wiping cycle, pull down on the band to
MIST. Hold it there until the wipers start, then let go.
The wipers will stop after one cycle. If you want more
cycles, hold the band on MIST longer.You can set the wiper speed for a long delay or short
delay between wipes. This can be very useful in light
rain or snow. Push the lever up one click to INT
(intermittent), then turn the band, located on the lever, to
adjust the delay time. Turn the band down for a longer
delay, up for a shorter delay. The wiper speed can only
be adjusted when the lever is in the INT position, not in
HI or LO.
Be sure to clear the ice and snow from the wiper blades
before using them. If they're frozen to the windshield,
carefully loosen or thaw them. If your blades do become
damaged, get new blades or blade inserts.
Heavy snow or ice can overload your wipers. A circuit
breaker will stop them until the motor cools. Clear away
snow or ice to prevent an overload.
ProCarManuals.com

yellowblue
2-34 Windshield Washer
At the end of the right-hand lever on the steering wheel,
there is a wiper symbol. To spray washer fluid on the
windshield, push the button on the end of the lever. The
wipers will run for several sweeps and then either stop
or return to your preset speed.
CAUTION:
In freezing weather, don't use your washer until
the windshield is warmed. Otherwise the washer
fluid can form ice on the windshield, blocking
your vision.
Cruise Control
With cruise control, you can maintain a speed of about
25 mph (40 km/h) or more without keeping your foot on
the accelerator. This can really help on long trips.
Cruise control does not work at speeds below about
25 mph (40 km/h).
When you apply your brakes, the cruise control
shuts off.
CAUTION:

Cruise control can be dangerous where you
can't drive safely at a steady speed. So,
don't use your cruise control on winding
roads or in heavy traffic.

Cruise control can be dangerous on
slippery roads. On such roads, fast changes
in tire traction can cause needless wheel
spinning, and you could lose control. Don't
use cruise control on slippery roads.
If your vehicle is in cruise control when the traction
control system (optional with the 3.5L V6 engine) or
enhanced traction system (3800 V6 engine) begins to
limit wheel spin, the cruise control will automatically
disengage. (See ªTraction Control Systemº or
ªEnhanced Traction Systemº in the Index.) When road
conditions allow you to safely use it again, you may turn
the cruise control back on.
ProCarManuals.com

yellowblue
2-35
Setting Cruise Control
CAUTION:
If you leave your cruise control switch on when
you're not using cruise, you might hit a button
and go into cruise when you don't want to. You
could be startled and even lose control. Keep the
cruise control switch off until you want to use it.
1. Press the CRUISE
button on the right side
of the instrument panel
to turn it on. A light on
the button will indicate
that the system is on.
2. Get up to the speed you want.
3. Press the COAST SET
button on your steering
wheel and release it.
4. Take your foot off the accelerator.
The CRUISE light on the instrument panel cluster will
come on after the cruise control has been set to the
desired speed. It will go off when you:

step lightly on the brake pedal,

press CLEAR on the steering wheel or

press the CRUISE button on the instrument panel.
ProCarManuals.com

yellowblue
2-36
Resuming a Set Speed
Suppose you set your cruise control at a desired speed
and then you apply the brake. This, of course shuts off
the cruise control. But you don't need to reset it.
Once you're going about
25 mph (40 km/h) or more,
press the RES ACCEL
button on your steering
wheel. You'll go right back
up to your chosen speed and
stay there.
Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed:

Use the accelerator pedal to get to the higher speed.
Press the COAST SET button on the steering wheel,
then release the button and the accelerator pedal.
You'll now cruise at the higher speed.
Press the RES ACCEL button on the steering wheel.
Hold it there until you get up to the speed you want
and then release the button. (To increase your speed
in very small amounts, press the RES ACCEL button
for less than half a second and then release it.
Each time you do this, your vehicle will go
1 mph (1.6 km/h) faster.)
The accelerate feature will only work after you set the
cruise control speed by pressing the COAST SET button
on the steering wheel.
Reducing Speed While Using Cruise Control
There are two ways to reduce your speed while using
cruise control:

Press the COAST SET button on the steering wheel
until you reach the lower speed you want, then
release it.

To slow down in very small amounts, press the
COAST SET button on the steering wheel for less
than a half second. Each time you do this, you'll go
1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot off the pedal, your vehicle will slow
down to the cruise speed you set earlier.
ProCarManuals.com

yellowblue
2-37
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear
to keep your speed down. Of course, applying the brake
takes you out of cruise control. Many drivers find this to
be too much trouble and don't use cruise control on
steep hills.
Ending Cruise Control
There are three ways to cancel the cruise control:

Step lightly on the brake pedal,

Press CLEAR on the steering wheel or

Press the CRUISE button on the instrument panel.
Erasing Cruise Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.Exterior Lamps
The lamp controls are located on the multifunction
lever on the left of the steering wheel. They control
these systems:

Headlamps

Taillamps

Parking Lamps

License Lamps

Sidemarker Lamps

Instrument Panel Lights
Turn the end of the lever to this symbol to turn on
the headlamps and other operating lamps.
Turn the end of the lever to this symbol to turn
on the parking and other operating lamps without
the headlamps.
Turn the end of the lever to OFF to turn off the lamps.
A warning chime will sound if you open the driver's
door when you turn the ignition switch to OFF or ACC
with the lamps on.
ProCarManuals.com

yellowblue
2-49
Your instrument panel is designed to let you know at a glance how your vehicle is running. You'll know how fast
you're going, about how much fuel is in your tank and many other things you need to drive safely and economically.
The main components of your instrument panel are:
A. Side Window Defogger Vent
B. Instrument Panel Outlets
C. Turn Signal/Multifunction Lever
D. Instrument Panel Cluster
E. Windshield Wipers/Washer Fluid Lever
F. Cruise Control (CRUISE) Button
G. Hazard Switch
H. Instrument Panel Fuse Block
I. Instrument Panel Dimmer
J. Fog Lamp Button
K. Fuel Door Release
L. Trunk Lid ReleaseM. Storage Bin
N. Trip Odometer
O. Tilt Wheel
P. Audio Steering Wheel Controls (If Equipped)
Q. Horn
R. Cruise Control Controls (RES ACCEL, CLEAR,
COAST SET)
S. Ignition Switch
T. Accessory Power Outlet
U. Comfort Controls
V. Audio System
W. Glove Box
ProCarManuals.com

yellowblue
2-56
The anti-lock brake system warning light should come
on briefly when you turn the ignition key to ON. If the
light doesn't come on then, have it fixed so it will be
ready to warn you if there is a problem.
Traction Control System Warning Light
(Option With 3.5L V6 Engine)
This warning light should
come on briefly as you
start the engine.
If the warning light doesn't come on then, have it fixed
so it will be ready to warn you if there's a problem. If it
stays on, or comes on when you're driving, there may be
a problem with your traction control system and your
vehicle may need service. When this warning light is on,
the system will not limit wheel spin. Adjust your driving
accordingly.The traction control system warning light may come on
for the following reasons:

If you turn the system off by pressing the
TRACTION CONTROL button located on the
console, the warning light will come on and stay on.
To turn the system back on, press the TRACTION
CONTROL button again. The warning light should
go off. (See ªTraction Control Systemº in the Index
for more information.)

If there's a brake system problem that is specifically
related to traction control, the traction control system
will turn off and the warning light will come on. If
your brakes begin to overheat, the traction control
system will turn off and the warning light will come
on until your brakes cool down.

If the traction control system is affected by an
engine
-related problem, the system will turn off and
the warning light will come on.
If the traction control system warning light comes on
and stays on for an extended period of time when the
system is turned on, your vehicle needs service.
ProCarManuals.com