key battery OLDSMOBILE INTRIGUE 1999 Owners Manual

yellowblue
1-26
CAUTION:
For up to 10 minutes after the ignition key is
turned off and the battery is disconnected, an air
bag can still inflate during improper service. You
can be injured if you are close to an air bag when
it inflates. Avoid yellow connectors. They are
probably part of the air bag system. Be sure to
follow proper service procedures, and make sure
the person performing work for you is qualified
to do so.
The air bag system does not need regular maintenance.
Rear Seat Passengers
It's very important for rear seat passengers to buckle up!
Accident statistics show that unbelted people in the rear
seat are hurt more often in crashes than those who are
wearing safety belts.
Rear passengers who aren't safety belted can be thrown
out of the vehicle in a crash. And they can strike others
in the vehicle who are wearing safety belts.
Rear Seat Outside Passenger Positions
Lap-Shoulder Belt
The positions next to the windows have lap
-shoulder
belts. Here's how to wear one properly.
ProCarManuals.com

yellowblue
2-6
If the driver wishes to let the Last Door Closed Locking
feature complete the locking of the vehicle, no
additional action is required. The Last Door Closed
Locking feature will lock the doors automatically after
all the doors have been closed for a period of five
seconds. During this five second period, any door may
be reopened, at which time the three possible actions
shown previously are again available.
You can customize the vehicle to activate the Last Door
Closed Locking feature as described previously or to
completely disable the Last Door Closed Locking
feature at all times. If disabled, the doors will lock
immediately when a power door lock switch is pressed.
The Last Door Closed locking feature is customized
when the driver performs the following sequence with
the doors closed and the ignition key in ON.
1. Press and hold the power door lock switch in the
unlock position.
2. While holding the door unlock switch, cycle the
transaxle out of and back into PARK (P).3. After an initial transaxle cycle, each additional cycle
will turn the Last Door Closed Locking feature on
or off.
4. During this customization procedure, the chime will
sound, providing the driver feedback. A single chime
will be heard if the Last Door Closed Locking
feature is off, and two chimes will be heard if the
Last Door Closed Locking feature is on.
5. When the door unlock switch is released, the vehicle
will remain in the most recent operating mode.
The Last Door Closed Locking feature is enabled when
the vehicle is shipped from the factory.
Disconnecting the battery for up to a year will not
change the programmed mode of the Last Door Closed
Locking feature.
ProCarManuals.com

yellowblue
2-7 Programmable Automatic Power Door
Locks (ADL)
Programmable Automatic Power Door Locks is a
standard feature intended to provide enhanced security
and convenience by automatically locking and
unlocking vehicle doors. The automatic locking and
unlocking of the vehicle will occur if the ignition key is
in ON and the driver's door is closed when the vehicle is
shifted out of PARK (P). One of four operating modes
may be selected and programmed by the driver:
Mode 1: No automatic door lock or unlock.
Mode 2: Automatic all door lock when transaxle is
shifted out of PARK (P). No automatic door unlock.
Mode 3: Automatic all door lock when transaxle is
shifted out of PARK (P). Automatic all door unlock
when transaxle is shifted into PARK (P).
Mode 4: Automatic all door lock when transaxle is
shifted out of PARK (P). Automatic driver's door only
unlock when transaxle is shifted into PARK (P).
The operating mode of the Programmable Automatic
Power Door Locks will be changed when the driver
performs the following sequence with the doors closed
and the ignition key in ON.1. Press and hold the power door lock switch in the
lock position.
2. While holding the door lock switch, cycle the
transaxle out of and back into PARK (P).
3. After an initial transaxle cycle, each additional cycle
will advance to the operating mode by one, starting
from the current operating mode.
4. During this customization procedure, the Automatic
Door Lock and Unlock functions will operate as
defined by each mode listed, providing the customer
with feedback of the current operating mode.
5. If cycled beyond mode 4, the vehicle will enter
operating mode 1. When the door lock switch is
released, the vehicle will remain in the most recent
operating mode.
The Programmable Automatic Power Door Locks are in
operating mode 3 when the vehicle is shipped from
the factory.
Disconnecting the battery for up to a year will not
change the programmed mode of the Programmable
Automatic Power Door Locks.
ProCarManuals.com

yellowblue
2-9
Keyless Entry System (If Equipped)
If your vehicle is equipped you can lock and unlock
your doors or unlock your trunk from about 3 feet (1 m)
up to 30 feet (9 m) away using the remote keyless entry
transmitter supplied with your vehicle.
Your keyless entry
system operates on a radio
frequency subject to
Federal Communications
Commission (FCC) Rules
and with Industry Canada.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference received,
including interference that may cause undesired operation.This device complies with RSS
-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation of
the device.
Changes or modifications to this system by other than an
authorized service facility could void authorization to
use this equipment.
This system has a range of about 3 feet (1 m) up to
30 feet (9 m). At times you may notice a decrease in
range. This is normal for any remote keyless entry
system. If the transmitter does not work or if you have
to stand closer to your vehicle for the transmitter to
work, try this:

Check to determine if battery replacement is
necessary. See the instructions that follow.

Check the distance. You may be too far from your
vehicle. You may need to stand closer during rainy
or snowy weather.

Check the location. Other vehicles or objects may be
blocking the signal. Take a few steps to the left or
right, hold the transmitter higher, and try again.

If you're still having trouble, see your dealer or a
qualified technician for service.
ProCarManuals.com

yellowblue
2-11
The operating mode of the Remote Activation
Verification Lock (RAV Lock) feature will be changed
when the driver performs the following sequence with
the doors closed and the ignition key in ON:
1. Press and hold down the power door lock switch
to LOCK.
2. While holding the door lock switch, press and
release the remote keyless entry transmitter LOCK
button. This button press will initialize the
customization mode. Upon initiation of this mode,
the chime will sound the number of chimes
corresponding to the current RAV lock mode.
3. Each additional press of the remote keyless entry
transmitter LOCK button will cause the vehicle to
advance to the RAV lock mode by one, starting from
the current RAV lock mode.
4. If cycled beyond RAV lock mode 4, the vehicle will
enter RAV lock mode 1. When the door lock switch
is released, the vehicle will remain in the most recent
RAV lock mode.
Disconnecting the battery for up to a year will not
change the programmed mode of the Remote Activation
Verification functions.Illumination on Remote Activation
This feature is included on vehicles with the remote
keyless entry system. The interior illumination will be
activated when an remote keyless entry door unlock
command is received. The ignition must be off for the
Remote Activation Illumination to work. The interior
lamps will illuminate until the ignition is turned to ON
or until the illumination period of 40 seconds
has elapsed.
If during the illumination period, a door is opened, the
timed illumination period will be cancelled, though the
interior lamps will remain on until all doors are closed.
Matching Transmitter(s) To Your Vehicle
Each remote keyless entry transmitter is coded to
prevent another transmitter from unlocking your vehicle.
If a transmitter is lost or stolen, a replacement can be
purchased through your dealer. Remember to bring any
remaining transmitters with you when you go to your
dealer. When the dealer matches the replacement
transmitter to your vehicle, any remaining transmitters
must also be matched. Once your dealer has coded the
new transmitter, the lost transmitter will not unlock your
vehicle. Each vehicle can have only four transmitters
matched to it.
ProCarManuals.com

yellowblue
2-12 Battery Replacement
Under normal use, the battery in your remote keyless
entry transmitter should last about two years.
You can tell the battery is weak if the transmitter won't
work at the normal range in any location. If you have to
get close to your vehicle before the transmitter works,
it's probably time to change the battery.
NOTICE:
When replacing the battery, use care not to touch
any of the circuitry. Static from your body
transferred to these surfaces may damage
the transmitter.
To replace your battery:
1. Insert a flat object like a dime into the slot on the
back of the transmitter. Gently pry apart the front
and back.
2. Gently pry the battery out of the transmitter. (Do not
use a metal object.)
3. Put the new battery into the transmitter as shown on
the transmitter (use a type CR2032 battery).
4. Put the two halves back together. Make sure the
halves are together tightly so water won't get in.
5. Resynchronize and then test the transmitter.
ProCarManuals.com

yellowblue
2-13 Resynchronization
After you have changed the battery in your remote
keyless entry transmitter, you will need to resynchronize
the transmitter. To do this, press the LOCK and
UNLOCK buttons together and hold for approximately
seven seconds (or until the horn chirps three times). You
will need to use this procedure if your vehicle has lost
battery power for an extended period of time.
Trunk Lid
CAUTION:
It can be dangerous to drive with the trunk lid
open because carbon monoxide (CO) gas can
come into your vehicle. You can't see or smell
CO. It can cause unconsciousness and even death.
CAUTION: (Continued)
CAUTION: (Continued)
If you must drive with the trunk lid open or if
electrical wiring or other cable connections must
pass through the seal between the body and
the trunk:

Make sure all other windows are shut.

Turn the fan on your heating or cooling
system to its highest speed with the setting
on VENT. That will force outside air into
your vehicle. See ªComfort Controlsº in
the Index.

If you have air outlets on or under the
instrument panel, open them all the way.
See ªEngine Exhaustº in the Index.
Trunk Lock
To unlock the trunk from the outside, insert the key and
turn it clockwise.
You can also use the remote keyless entry transmitter, if
your vehicle is equipped.
ProCarManuals.com

yellowblue
2-18
NOTICE:
Holding your key in START for longer than
15 seconds at a time will cause your battery to be
drained much sooner. And the excessive heat can
damage your starter motor. Wait about
15 seconds between each try to help avoid
draining your battery or damaging your starter.
2. If it doesn't start right away, hold your key in
START for about ten seconds at a time until your
engine starts. Wait about 15 seconds between each
try to help avoid draining your battery or damaging
your starter.
3. If your engine still won't start (or starts but then
stops), it could be flooded with too much gasoline.
Try pushing your accelerator pedal all the way to the
floor and holding it there as you hold the key in
START for about three seconds. If the vehicle starts
briefly but then stops again, do the same thing, but
this time keep the pedal down for five or six seconds.
This clears the extra gasoline from the engine.
After waiting about 15 seconds, repeat the normal
starting procedure.
NOTICE:
Your engine is designed to work with the
electronics in your vehicle. If you add electrical
parts or accessories, you could change the way
the engine operates. Before adding electrical
equipment, check with your dealer. If you don't,
your engine might not perform properly.
If you ever have to have your vehicle towed, see
the part of this manual that tells how to do it
without damaging your vehicle. See ªTowing
Your Vehicleº in the Index.
Starting Your 3800 Series II V6 Engine
1. Without pushing the accelerator pedal, turn your
ignition key to START. When the engine starts, let
go of the key. The idle speed will go down as your
engine gets warm.
ProCarManuals.com

yellowblue
2-19
NOTICE:
Holding your key in START for longer than
15 seconds at a time will cause your battery to be
drained much sooner. And the excessive heat can
damage your starter motor. Wait about
15 seconds between each try to help avoid
draining your battery or damaging your starter.
2. If it doesn't start right away, hold your key in
START for about three to five seconds at a time until
your engine starts. Wait about 15 seconds between
each try to help avoid draining your battery or
damaging your starter.
3. If your engine still won't start (or starts but then
stops), it could be flooded with too much gasoline.
Try pushing your accelerator pedal all the way to the
floor and holding it there as you hold the key in
START for about three seconds. If the vehicle starts
briefly but then stops again, do the same thing, but
this time keep the pedal down for five or six seconds.
This clears the extra gasoline from the engine. After
waiting about 15 seconds, repeat the normal
starting procedure.
NOTICE:
Your engine is designed to work with the
electronics in your vehicle. If you add electrical
parts or accessories, you could change the way
the engine operates. Before adding electrical
equipment, check with your dealer. If you don't,
your engine might not perform properly.
If you ever have to have your vehicle towed, see
the part of this manual that tells how to do it
without damaging your vehicle. See ªTowing
Your Vehicleº in the Index.
ProCarManuals.com

yellowblue
2-41 Exit Illumination
To see better when exiting your vehicle at night, your
vehicle is equipped with an Exit Illumination feature.
The interior lamps will illuminate for up to 25 seconds
when you remove your key from the ignition. After
25 seconds have elapsed, the interior lamps will slowly
fade out. The lamps will fade out before the 25 seconds
have elapsed if you:

turn the ignition to ON.

lock all doors using your remote keyless entry
transmitter (if equipped).

lock the doors using the power door lock switch.
When any door is opened, Exit Illumination is
cancelled. The interior lamps will stay on while any
door is opened. The interior lamps may stay on for up to
25 seconds after all the doors have been closed if they
have not been locked. See ªDelayed Illuminationº in
the Index.
Battery Saver
Your vehicle has a feature to help prevent you from
draining the battery in case you accidentally leave an
interior or trunk lamp on. If you leave any of these
lamps on while the ignition is in ACC or OFF, they will
automatically turn off after 20 minutes. The lamps won't
come back on until you do one of the following:

turn the ignition to ON,

turn the interior lamp dial all the way up or

open (or close and reopen) a door that is closed.
Note that if your vehicle has less than 15 miles (25 km)
on the odometer, the battery saver will turn off the lamps
after only three minutes.
Mirrors
Adjust all mirrors so you can see clearly when you are
sitting in a comfortable position.
Inside Day/Night Rearview Mirror
To reduce glare from lamps behind you, push the
lever away from you (to the night position). To return
the mirror back to the day position, pull the lever
toward you.
ProCarManuals.com