bulb Oldsmobile Intrigue 2000 s User Guide

6-35
4. Remove the rubber access cover from behind the
bulb you are replacing.
5. Twist and turn the bulb socket counterclockwise and
remove it from the lamp.6. Replace the bulb, making sure you don't touch the
bulb with your bare hands.
7. Reverse all steps and reinstall the headlamp
assembly, then check the lamps.

6-38 Front Parking, Sidemarker and Turn Signal
Cornering Lamp
1. Remove the headlamp assembly. Refer to the
removal procedure listed under ªHeadlampsº earlier
in this section.
2. Remove the rubber bulb access cover.
3. Twist and pull each bulb socket from the
headlamp assembly.
4. Holding the base of the bulb, pull the bulb from
the socket.
5. Push the new bulb into the socket.
6. Put the bulb socket back into the headlamp assembly
and turn it clockwise until it is secure.
7. Reinstall the rubber access cover.
Fog Lamps
1. Remove the deflector located below the front fascia
by removing the two bolts.
2. Reach up from underneath the front of the vehicle and
remove the electrical connector from the bulb assembly.
3. Turn the bulb socket a quarter turn counterclockwise
to remove.
4. Remove the bulb from the socket.
5. Place the new bulb into the socket.
6. Reverse the steps to reinstall.

6-39 Center High-Mounted Stoplamp (CHMSL)
1. Open the trunk.
2. Reach through the access opening in the trunk.
3. Remove the bulb by turning it one quarter
turn counterclockwise.
4. Place the new bulb into the socket.
5. Turn the bulb one quarter turn clockwise to reinstall.
6. Close the trunk.

6-40 Tail/Stop/Turn Signal lamp
1. Unscrew the wing nut inside of the trunk (1) behind
the taillamp to be changed (if equipped with a
convenience net, unhook the net).
2. Pull back the carpeting.
3. Remove the plastic wing nuts (2).
(Pliers may be required to remove the wing nuts.)4. Pull the taillamp housing away from the body
of the vehicle (3).
5. Squeeze the tab on the bulb socket and turn the
socket counterclockwise.
6. Pull out the bulb socket.
7. Pull the old bulb out of the socket.
(There are four bulbs on each taillamp.)
8. Push in a new bulb.
9. Reinstall the bulb socket into the housing and turn
it clockwise.
10. Reinstall the taillamp housing to the body
of the vehicle.
11. Reinstall the wing nuts.
12. Tighten the plastic nuts.

6-41 License Plate Lamp
1. Remove the four screws to remove the name plate.
2. Reach your hand up through underside of the trunk
into the slots.
3. Press the clip on one side of the bulb assembly
and pull out the assembly from the front with your
other hand.4. Remove the bulb from the socket.
5. Place the new bulb into the socket.
6. Reverse the steps to reinstall.
When reinstalling bulb assembly, push in assembly
until you hear a snap. Make sure the assembly is tight
and not loose.
Windshield Wiper Blade Replacement
Windshield wiper blades should be inspected at least
twice a year for wear or cracking. See ªWiper Blade
Checkº in Section 7 of this manual under Part B ªOwner
Checks and Servicesº for more information.
Replacement blades come in different types and are
removed in different ways. For the proper type and
length, see ªNormal Maintenance Replacement Partsº in
the Index.

6-66
Replacement Bulbs
Center High-Mounted Stop Lamp (CHMSL) 1141. .
Fog Lamp 893. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Parking/Turn Signal 4157 NAK. . . . . . . . . . . . .
Headlamp
High Beam 9005. . . . . . . . . . . . . . . . . . . . . . . . . . .
Low Beam 9006. . . . . . . . . . . . . . . . . . . . . . . . . . . .
License Plate Lamp 194. . . . . . . . . . . . . . . . . . . . . . .
Sidemarker (Front/Rear) 194. . . . . . . . . . . . . . . . . . .
Stop/Tail/Turn Signal (Rear) 3057. . . . . . . . . . . . . . .
Cornering 3156. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capacities and Specifications
Please refer to ªRecommended Fluids and Lubricantsº
in the Index for more information.
Automatic Transaxle
After Complete Overhaul 10.0 quarts (9.5 L). . . . . . .
Pan Removal
and Replacement 7.4 quarts (7.0 L). . . . . . . . . . . . .
When draining/replacing the converter, more fluid
may be needed.Cooling System Including Reservoir
10.0 quarts (9.5 L)
A/C Refrigerant1.9 lbs. (0.85 kg) . . . . . . . . . . . . . . .
Engine Crankcase (Oil and Filter Change)
6.0 quarts (5.7 L)
Fuel Tank17 gallons (64 L) . . . . . . . . . . . . . . . . . . . .
NOTE: All capacities are approximate. When adding, be
sure to fill to the appropriate level, as recommended in
this manual. Recheck fluid level after filling.
Engine Specifications
Type V6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displacement 212 cubic inches (3.5 L). . . . . . . . . . . .
Compression Ratio 9.3:1. . . . . . . . . . . . . . . . . . . . . . .
Firing Order 1
-2-3-4-5-6 . . . . . . . . . . . . . . . . . . . . . .
Thermostat Temperature 180
F (82
C) . . . . . . . . . . .
Horsepower 215. . . . . . . . . . . . . . . . . . . . . . . . . . . . .