ECU Oldsmobile Intrigue 2001 s User Guide

1-46 Securing a Child Restraint in the Center
Rear Seat Position
You'll be using the lap belt. Be sure to follow the
instructions that came with the child restraint.
Secure the child in the child restraint when and
as the instructions say.
See the earlier part about the top strap if the child
restraint has one.
1. Make the belt as long as possible by tilting the latch
plate and pulling it along the belt.
2. Put the restraint on the seat.
3. Run the vehicle's safety belt through or around the
restraint. The child restraint instructions will show
you how.

1-47
4. Buckle the belt. Make sure the release button is
positioned so you would be able to unbuckle the
safety belt quickly if you ever had to.5. To tighten the belt, pull its free end while you push
down on the child restraint. If you're using a
forward
-facing child restraint, you may find it
helpful to use your knee to push down on the child
restraint as you tighten the belt.
6. Push and pull the child restraint in different
directions to be sure it is secure.
To remove the child restraint, just unbuckle the vehicle's
safety belt. It will be ready to work for an adult or larger
child passenger.

1-48 Securing a Child Restraint in the Right
Front Seat Position
Your vehicle has a right front passenger air bag. Never
put a rear
-facing child restraint in this seat. Here's why:
CAUTION:
A child in a rear-facing child restraint can be
seriously injured or killed if the right front
passenger's air bag inflates. This is because the
back of the rear
-facing child restraint would be
very close to the inflating air bag. Always secure
a rear
-facing child restraint in the rear seat.
Although a rear seat is a safer place, you can secure a
forward
-facing child restraint in the right front seat.
You'll be using the lap
-shoulder belt. See the earlier part
about the top strap if the child restraint has one. Be sure
to follow the instructions that came with the child
restraint. Secure the child in the child restraint when and
as the instructions say.
1. Because your vehicle has a right front passenger air
bag, always move the seat as far back as it will go
before securing a forward
-facing child restraint.
See ªSeatsº in the Index.
2. Put the restraint on the seat.
3. Pick up the latch plate, and run the lap and shoulder
portions of the vehicle's safety belt through or
around the restraint. The child restraint instructions
will show you how.

1-51
To tighten the belt, feed the shoulder belt back
into the retractor while you push down on the
child restraint. You may find it helpful to use your
knee to push down on the child restraint as you
tighten the belt.

If your vehicle doesn't have the child restraint
locking feature on the shoulder belt retractor,
tighten the belt by pulling up on the shoulder
belt while you push down on the child restraint.
You may find it helpful to use your knee to
push down on the child restraint as you tighten
the belt.
6. Push and pull the child restraint in different
directions to be sure it is secure.
To remove the child restraint, just unbuckle the vehicle's
safety belt and let it go back all the way. The safety belt
will move freely again and be ready to work for an adult
or larger child passenger.

2-9 Programmable Automatic Door Locks
Programmable automatic door locks is a standard
feature intended to provide enhanced security and
convenience by automatically locking and unlocking
vehicle doors. The automatic locking and unlocking of
the vehicle will occur if the ignition key is in ON and
the driver's door is closed when the vehicle is shifted
out of PARK (P).
Programmable Modes
Mode 1: No automatic door lock or unlock.
Mode 2: Automatic all door lock when the transaxle is
shifted out of PARK (P). No automatic door unlock.
Mode 3: Automatic all door lock when the transaxle is
shifted out of PARK (P). Automatic all door unlock
when the transaxle is shifted into PARK (P).
Mode 4: Automatic all door lock when the transaxle is
shifted out of PARK (P). Automatic driver's door only
unlock when the transaxle is shifted into PARK (P).
When your vehicle was shipped from the factory, it was
programmed to Mode 3. The mode to which your
vehicle was programmed may have been changed since
it left the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:1. Close all doors and turn the ignition switch to ON.
2. Press and hold the power door lock switch in the
lock position.
3. While holding the door lock switch, cycle the
transaxle out of and back into PARK (P). The door
lock and unlock functions will operate as defined,
depending upon the current mode selected. (If you
do not wish to change the current mode, you can
either exit the programming mode by following the
instructions listed here or program the next feature
available on your vehicle).
4. After an initial transaxle cycle, each additional cycle
will advance to the operating mode by one, starting
from the current operating mode.
5. If cycled beyond Mode 4, the vehicle will enter
operating Mode 1. When the door lock switch is
released, the vehicle will remain in the most recent
operating mode.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
above or program the next feature available on
your vehicle.
Disconnecting the battery for up to a year will not
change or delete any previously programmed modes.

2-10 Rear Security Locks
Your vehicle is equipped
with rear door security
locks that help prevent
passengers from opening
the rear doors of your
vehicle from the inside.
To use one of these locks, do the following:
1. Open one of the rear doors.
2. On the inside of the rear door will be a lock. Insert
your master key into this lock and turn it upward.
This will engage the safety lock.
3. Close the door.
4. Do the same thing to the other rear door.The rear doors on your vehicle cannot be opened from
the inside when this feature is in use. If you want to
open the rear door when the security lock is on, unlock
the door from the inside and then open the door from
the outside.
Lockout Prevention
Lockout Prevention is a standard feature intended to
provide enhanced security and convenience. This feature
prevents a driver who has left the key in the ignition
from locking the doors using the power door lock
switch while any door is open.
This feature cannot guarantee that you will never be
locked out of your vehicle. If you don't leave the key
in the ignition, or if you use the manual door lock,
you could still lock your keys inside your vehicle.
Always remember to take your keys with you.
Programmable Modes
Mode 1: Turns feature on.
Mode 2: Turns feature off.

2-13
Remote Alarm
When you press the alarm button on the remote keyless
entry transmitter, the headlamps will flash, the horn will
sound repeatedly and the interior lamps will illuminate.
This will allow you to attract attention if needed. The
alarm will continue until one of the following occurs:

The driver presses the alarm button on the remote
keyless entry transmitter a second time,

the ignition is turned to ON or

110 seconds has elapsed.
Remote Activation Verification (RAV)
This feature helps provide audible and/or visible
feedback that a remote keyless entry lock or unlock
command has been received and executed. The ignition
must be in OFF for the remote activation verification
to work.
You may select one of four operating modes for lock and
unlock commands. The selection and programming of the
lock and unlock modes are independent of each other.
Programmable Modes
Mode 1: No Verification
Mode 2: Horn Chirp onlyMode 3: Headlamp and Parking Lamp Flash only
Mode 4: Horn Chirp and Headlamp and Parking
Lamp Flash
RAV Lock Mode Programming
When your vehicle was shipped from the factory, it was
programmed to Mode 3. The mode to which your
vehicle was programmed may have been changed since
it left the factory. To determine the RAV lock mode to
which your vehicle is programmed to or to program
your vehicle to a different mode, do the following:
1. Close all doors and turn the ignition switch to ON.
2. Press and hold down the power door lock switch in
the LOCK position.
3. While holding the door lock switch, press and
release the remote keyless entry transmitter
LOCK button. This button press will initialize the
customization mode. Upon initiation of this mode,
the chime will sound. Count the number of chimes
you hear. The number of chimes tells you which
mode your vehicle is set for. (If you do not wish
to change the current mode, you can either exit the
programming mode by following the instructions
listed here or program the next feature available on
your vehicle).

2-17 Trunk Lock
To unlock the trunk from the outside, insert the key and
turn it clockwise.
You can also use the remote keyless entry transmitter
(if equipped).
Remote Trunk Release
Press the button on the
left side of the instrument
panel to unlock the trunk
from inside your vehicle.
Your vehicle must be
in PARK (P).
Trunk Release Handle (If Equipped)
NOTICE:
The trunk release handle was not designed to be
used to tie down the trunk lid or as an anchor
point when securing items in the trunk. Improper
use of the trunk release handle could damage it.
There is a glow-in-the-dark trunk release handle located
inside the trunk on the latch. This handle will glow
following exposure to light. Pull the release handle up to
open the trunk from the inside.

2-19
Passlock
Your vehicle is equipped with the Passlock
theft
-deterrent system.
Passlock is a passive theft
-deterrent system. Passlock
enables fuel if the ignition lock cylinder is turned with a
valid key. If a correct key is not used or the ignition lock
cylinder is tampered with, fuel is disabled.
During normal operation, the SECURITY light will go
off approximately five seconds after the key is turned to
the START ignition position.
If the engine stalls and the SECURITY light flashes,
wait until the light stops flashing before trying to restart
the engine. Remember to release the key from START
as soon as the engine starts.
If the engine is running and the SECURITY light
comes on, you will be able to restart the engine if you
turn the engine off. However, your Passlock system
is not working properly and must be serviced by your
dealer. Your vehicle is not protected by Passlock at this
time. You may also want to check the fuse (see ªFuses
and Circuit Breakersº in the Index). See your dealer
for assistance.
In an emergency, contact Oldsmobile Roadside
Assistance. See ªRoadside Assistanceº in the Index for
more information.
New Vehicle ªBreak-Inº
NOTICE:
Your vehicle doesn't need an elaborate
ªbreak
-in.º But it will perform better in
the long run if you follow these guidelines:

Don't drive at any one speed -- fast or
slow
-- for the first 500 miles (805 km).
Don't make full
-throttle starts.

Avoid making hard stops for the first
200 miles (322 km) or so. During this time
your new brake linings aren't yet broken
in. Hard stops with new linings can mean
premature wear and earlier replacement.
Follow this breaking
-in guideline every
time you get new brake linings.

Don't tow a trailer during break
-in.
See ªTowing a Trailerº in the Index for
more information.

2-44 Illuminated Entry
Your courtesy lamps will come on and stay on for a
set time whenever you press UNLOCK on the remote
keyless entry transmitter (if equipped).
If you open a door, the lamps will stay on while it's open
then turn off automatically about 25 seconds after you
close it. If you press UNLOCK and don't open a door,
the lamps will turn off after about 40 seconds.
Illuminated entry includes a feature called theater
dimming. With theater dimming, the lamps don't just
turn off at the end of the delay time. Instead, they
slowly dim after the delay time until they go out.
The delay time is cancelled if you turn the ignition
key to ON so that the lamps will dim out right away.
When the ignition is on, illuminated entry is inactive,
which means the courtesy lamps won't come on unless
a door is opened.
Illumination on Door Handle Activation
Illumination on door handle activation is a standard
feature intended to provide enhanced security and
convenience by allowing the driver to activate the
vehicle interior illumination without unlocking or
opening any vehicle door.The ignition must be off and the doors locked for
the illumination on door handle activation to work.
The illumination on door handle activation feature
can function in two ways.
If the driver pulls and releases any front door handle
within one second, the interior lamps will illuminate
until one of the following occurs:

The ignition is turned to ON,

the power door locks are activated or

an illumination period of 25 seconds has elapsed.
Or, if the driver pulls and holds any front door handle
for more than one second, the interior lamps will
illuminate until one of the following occurs:

The ignition is turned to ON,

the door handle is released or

an illumination period of 50 seconds has elapsed.
If during the illumination period a door is opened,
the timed illumination period will be cancelled, though
the interior lamps will remain on because a vehicle door
is open.