bulb OPEL ANTARA 2009 Owners Manual

Instruments, controls72
o
Electronic immobiliser
Illuminates in red when ignition is
switched on, then extinguishes.
If it remains illuminated after the ignition is
on, there is a fault in the immobiliser
system; the engine cannot be started -
see page 22.
9Door open
Illuminates in red when a door is open.
3Engine electronics,
transmission electronics 3
Illuminates in yellow when ignition is
switched on, then extinguishes.
If it illuminates
during driving;
there may be a fault in the engine or
transmission electronics: interrupt your
journey and consult a workshop as soon as
possible.
Further information - see page 134.
vAirbag systems 3 , belt tensioners
see pages 44, 52.
1Tailgate open
Illuminates in red when ignition is
switched on, then extinguishes.
Illuminates when tailgate is open or not
securely latched.
Tailgate - see page 26.
XDriver’s seat belt reminder
Illuminates in red when ignition is
switched on, then extinguishes.
When the engine is runn ing, if driver’s seat
belt is not engaged, it will flash for approx.
90 seconds and then illuminate until
driver’s seat belt is fastened.
If vehicle speed exceeds approx. 22 km/h
(14 mph), control indicator will flash for
approx. 90 seconds along with a warning
chime and then remains illuminated until
driver’s seat belt is fastened.
Seat belts - see page 43.
OTurn signal lamps
The relevant control indicator flashes in
green when the turn signal is on.
Rapid flash; failure of a turn signal bulb or
the corresponding fuse or failure of a trailer
turn signal bulb 3. Both control indicators
flash when the hazard warning lamps are
active.
Further information - see pages 14, 95.
Bulb replacement - see page 185.
Fuses - see page 181.
YLow fuel level
Illuminates in yellow when ignition is
switched on, then extinguishes.
If it illuminates during dr iving; fuel level low:
fill up fuel tank as soon as possible.
Never let the tank run dry.
Erratic fuel supply can cause catalytic
converter to overheat - see page 133.
Diesel engines: if the tank has been run dry,
bleed the fuel system as described on
page 171.
Refuelling - see page 132.
Fuel tank capacity - see page 225.

Self-help, vehicle care171
Self-help, vehicle care
Diesel fuel system, bleeding
Never let the fuel tank run dry. If control
indicator Y illuminates, refuel as soon as
possible.
It is possible to restart the engine if the tank
has been run dry. A delayed start can be
expected. Switch on the ignition three times
for approx. 15 seconds. Then try to start
the engine for no more than 40 seconds. If
the engine will not start, wait at least
10 seconds before trying again. If the
engine will still not start, consult a
workshop.
Bonnet
To open the bonnet, pull release lever /
located on the left-hand side below the
instrument panel.
The bonnet will then be unlocked and will
partially open. Return release lever to its
original position.
Do not pull release lever while the vehicle is
moving.
Diesel fuel system, bleeding .............. 171
Bonnet ................................................. 171
Starting ................................................ 172
Starting the engine with jump leads
3 172
Towing ................................................. 174
Jack and vehicle tools ........................ 176
Warning triangle ¨ 3 ,
First aid kit +3................................ 177
Temporary spare wheel ..................... 177
Wheel changing .................................. 178
Electrical system ................................. 181
Fuses and the most important circuits they protect ...................................... 182
Bulb replacement ............................... 185
Opel genuine parts and accessories . 191
A note on safety ................................. 191
Checking and topping up fluids ........ 191
Windscreen wipers .............................. 198
Windscreen washer system ................ 199
Battery ................................................. 200
Protection of electr onic components 201
Vehicle storage ................................... 201
Vehicle care......................................... 201
9 Warning
Disregard of the instructions may lead to
injuries or endanger life. Vehicle
passengers must be informed
accordingly.

Self-help, vehicle care185
Bulb replacement
Before replacing a bulb , switch off ignition
and relevant switch.
Only hold new bulbs at base! Do not touch
the bulb glass with bare hands, otherwise
fingerprints on the glass evaporate and
residue builds up on the reflector
eventually resulting in a dull reflector.
Inadvertently stained bulbs may be
cleaned with a clean lint-free cloth, using
alcohol or white spirit.
Replacement bulb must be in accordance
with data on base of defective bulb. Do not
exceed wattage given on bulb base.
Headlamp aiming
We recommend that headlamp aiming be
carried out by a work shop, which will have
special equipment.
When aiming your headlamps, the manual
headlamp range adjustment 3 must be set
to 7. Headlamp removal
For bulb replacement, it is necessary to first
remove the headlamp assembly.
1. Switch off ignition and headlamp switch.
2. Open the bonnet, release the 11
retainers and remove the radiator cover.
3. Remove 3 bolts and withdraw headlamp.
4. Depress harness connector tags and disconnect head lamp wiring.
5. Remove the headlamp assembly.
Headlamp assembly installation is the
reverse of removal - ensure locating dowel
aligns with its socket.
Do not overtighten bolts or retainers.
No. Circuit Rating
22
Electric seat 30 A
23 Battery 60 A
24 Defogger 30 A
25 Dipped beam (left side) 15 A
26 Dipped beam (right side) 15 A
27 Parking lamp (left side) 10 A
28 Front fog lamps 15 A
29 Main beam 15 A
30 Rear wipers 20 A
31 --
32 Headlamp washer 20 A
33 Transmission Control
Module 15 A
34 Trailer/parking lamp
(left side) 10 A
35 Spare 25 A
36 Spare 20 A
37 Spare 15 A
38 Spare 10 A

Self-help, vehicle care186
Halogen headlamp system
Dipped and main beam
Main beam 1 (inner bulbs) and dipped
beam 2 (outer bulbs).
1. Remove headlamp assembly - seepage185.
2. Remove headlamp cap.
3. Release bulb retaining spring and remove bulb from reflector housing.
4. When fitting a new bulb, ensure the lugs engage correctly with the recesses on the
reflector. Do not touch the glass.
5. Engage bulb retaining spring and replace headlamp cap.
6. Reinstall headlamp assembly. Parking lamps
1. Remove headlamp assembly -
seepage185.
2. Remove headlamp cap and withdraw bulb holder (located next to main beam
bulb) from lamp assembly.
3. Remove bulb from bulb holder by pulling it straight out.
4. Install new bulb, using a lint-free cloth to hold bulb.
5. Reinstall bulb holder in lamp assembly and replace headlamp cap.
6. Reinstall headlamp assembly. Front turn signal lamps
1. Remove headlamp assembly -
see page 185.
2. Rotate bulb holder anti-clockwise and withdraw bulb holder from lamp
assembly.
3. Press and rotate bulb anti-clockwise to remove it from bulb holder.
4. Install new bulb into bulb holder by pressing and rotating it clockwise.
5. Reinstall bulb holder in lamp assembly
by rotating it clockwise.
6. Reinstall headlamp assembly.

Self-help, vehicle care187
Xenon headlamp system 3
Halogen headlamps A can be identified
from Xenon headlamps B by the different
lens layout. Parking lamps
1. Remove headlamp assembly -
seepage185.
2. Rotate bulb holder anti-clockwise and withdraw bulb holder from lamp
assembly.
3. Remove bulb from bulb holder by pulling it straight out.
4. Install new bulb, using a lint-free cloth to hold bulb.
5. Reinstall bulb holder in lamp assembly by rotating it clockwise.
6. Reinstall headlamp assembly. Front turn signal lamps
1. Remove headlamp assembly -
see page 185.
2. Rotate bulb holder anti-clockwise and withdraw bulb holder from lamp
assembly.
3. Press and rotate bulb anti-clockwise to remove it from bulb holder.
4. Install new bulb into bulb holder by pressing and rotating it clockwise.
5. Reinstall bulb holder in lamp assembly
by rotating it clockwise.
6. Reinstall headlamp assembly.
9 Warning
Xenon headlamps operate at very high
voltages. Do not touch; risk of fatal injury.
Have dipped beam and main beam
repaired by a workshop only.

Self-help, vehicle care188
Front fog lamps
1. Remove 2 screws from panel on underside of vehicle below front fog
lamps and remove panel.
2. Disconnect harness connector from bulb holder and rotate bulb holder anti-
clockwise.
3. Remove bulb holder from lamp assembly, rotate bulb anti-clockwise and
remove from bulb holder.
4. Install new bulb in to bulb holder and
rotate it clockwise.
5. Reinstall bulb holder in lamp assembly
and reconnect harness connector.
6. Reinstall panel to underside of vehicle using 2 screws removed earlier. Side repeater lamps
1. Using a suitable screwdriver, pry lamp
assembly away from wing.
2. Rotate bulb holder anti-clockwise.
3. Remove bulb from lamp assembly by pulling bulb straight out of bulb holder.
4. Install new bulb into bulb holder by pressing it in and rotating the bulb
holder clockwise.
5. Push lamp assembly back into aperture. Rear brake, tail, turn signal, reverse lamps
and fog tail lamp
1. Open the tailgate and remove 2 screws
and lamp assembly.
2. Remove bulb holder by rotating it anti-clockwise.
3. Remove bulb from bulb holder by pressing the bulb in and rotating it anti-
clockwise.
4. Install new bulb into bulb holder.
5. Reinstall bulb holder into lamp assembly. Rotate bulb holder clockwise and ensure
it is secure.

Self-help, vehicle care189
6. Replace lamp assembly by guiding lugs on lamp assembly into their holes (see
black arrows in illustration).
7. Replace 2 screws removed earlier and close the tailgate. License plate lamps
1. Remove 4 screws (arrowed) and remove
lamp covers.
2. Remove bulb holder from lamp assembly by rotating it anti-clockwise.
3. Pull bulb straight out of bulb holder.
4. Install new bulb.
5. Reinstall bulb holder into lamp assembly, rotate bulb holder clockwise and ensure
it is secure.
6. Replace lamp covers using 4 screws removed earlier. Front reading lamps
1. Using a suitable screwdriver, pry lamp
lens away from roof lining.
2. Remove bulb.
3. Install new bulb.
4. Reinstall lamp lens in roof lining.

Self-help, vehicle care190
Rear interior lamps
1. Using a suitable screwdriver, pry lamp lens away from roof lining.
2. Remove bulb.
3. Install new bulb.
4. Reinstall lamp lens in roof lining. Luggage compartment lamps
3
1. Using a suitable screwdriver, remove lens from lamp assembly.
2. Remove bulb.
3. Install new bulb.
4. Reinstall lens to lamp assembly. Front door lamps
1. Using a suitable screwdriver, pry lamp
lens away from front door trim.
2. Remove bulb.
3. Install new bulb.
4. Reinstall lamp lens to front door trim.

Self-help, vehicle care191
Centre high-mounted stop lamp,
instrument panel and glove compartment
illumination
We recommend having bulb replacements
carried out by a workshop.
Opel genuine parts and
accessories
We recommend the use of “Opel genuine
parts and accessories” and conversion
parts released expressly for your vehicle
type. These parts have undergone special
tests to establish their reliability, safety and
specific suitability for your vehicle. Despite
continuous market monitoring, we cannot
assess or guarantee these attributes for
other products, even if they have been
granted approval by the relevant
authorities or in some other form.
“Opel genuine parts and accessories” and
conversion parts approved by Opel can be
obtained from your Op el Partner, who can
provide comprehensive advice about
permitted technical changes and ensure
that the part is installed correctly.
A note on safety
To avoid the possibility of injury, only carry
out engine compartment checks (e.g.
checking the brake fluid level or the engine
oil level) when the igni tion is switched off. Never carry out any re
pairs or adjustment
and maintenance work on the vehicle
yourself. This especially applies to the
engine, chassis and safety parts. You may,
out of ignorance, infringe the provisions of
the law and, by not performing the work
properly, you may endanger yourself and
other road users.
Checking and topping up fluids
To aid identification, the engine oil filler
cap, the coolant filler cap, the lid of the
fluid container for the windscreen washer
system and the handle of the engine oil
gauge (dipstick) may be coloured yellow.
9 Warning
The cooling fan may be operated by a
thermoswitch and can therefore start to
operate unexpectedly, even when the
ignition is switched off; risk of injury.
Electronic ignition systems generate very
high voltages. Do not touch the ignition
system; high voltage can be fatal.

Index229
Brakes ..................................................... 145
ABS
..................................................... 148
Brake assist
........................................ 146
Brake fluid
.......................................... 196
Brake lamps
....................................... 188
Brake servo unit
................................. 127
Foot brake
.......................................... 146
Hand brake
........................................ 147
Bulb replacement
.................................. 185
Bulbs
....................................................... 185
C
Capacities .............................................. 225
Car Pass
................................................... 21
Caravan/trailer towing
.................. 127, 167
Card holder
.............................................. 67
Care
........................................................ 201
Catalytic converter
............... 133, 135, 172
Central locking switch
............................. 25
Central locking system
............................ 25
Centre high-mounted stop lamp Bulb replacement
.............................. 191
Changing the battery Remote control
.................................... 24
Changing tyre/wheel type
.................... 149
Changing wheels
................................... 178
Chassis number, see Vehicle
Identification Number
................... 215, 216
Check control
........................................... 91
Child restraint system
....................... 47, 58
Child safety locks
.................................... 30
Cigarette lighter
...................................... 68
Cleaning
................................................. 201
Climate control
...................................... 103 Clock
......................................................... 76
Clutch fluid
............................................. 197
Clutch operation
................................... 128
CO
2 emissions ........................................ 219
Coin storage
............................................ 67
Cold starts
...................................... 128, 133
Colour information display
............... 77, 83
Console box
............................................. 65
Console net
.............................................. 66
Contrast
................................................... 87
Control indicators
.............................. 12, 70
ABS
............................................... 70, 148
Airbags
........................................... 56, 72
All Wheel Drive
............................ 71, 121
Alternator
............................................. 74
Anti-theft alarm system
.......... 28, 29, 74
Automatic headlamp
range adjustment
.......................... 71, 97
Automatic transmission
.................... 120
Belt tensioners
............................... 45, 72
Brake system
....................... 70, 147, 197
Change engine oil
....................... 73, 194
Coolant temperature
.................. 71, 196
Cruise control
............................... 73, 140
Descent Control System
...... 71, 138, 139
Diesel particle filter
..................... 73, 135
Doors
.................................................... 72
Driver’s seat belt reminder
................. 72
Electronic immobiliser
................... 22, 72
Electronic Stability Control
......... 71, 136
Engine electronics
....................... 72, 134
Engine oil level
..................................... 73
Engine oil pressure
.............................. 74
Exhaust
........................................ 74, 134 Fog tail lamp
................................. 73, 96
Front fog lamps
............................. 73, 96
Front passenger’s seat belt reminder
46
Fuel level
........................................ 72, 76
Headlamp main beam
................. 73, 95
Park pilot
...................................... 71, 143
Power steering
..................................... 73
Preheating
........................................... 73
Tailgate
................................................ 72
Trailer
................................................... 70
Transmission electronics
..................... 72
Turn signal lamps
................................ 72
Water in diesel fuel
..................... 73, 195
Windscreen washer fluid
............ 73, 199
Winter program
........................... 74, 117
Coolant
.................................. 195, 214, 216
Coolant level
......................................... 195
Coolant temperature
...................... 71, 195
Cooled glove compartment
................. 105
Cooling
........................................... 110, 111
Correcting time
....................................... 86
Corrosion protection
............................. 214
Coupling socket load
............................ 168
Courtesy lamps
....................................... 98
Bulb replacement
.............................. 189
Switching off
........................................ 99
Cruise control
........................................ 140
Curtain airbags
....................................... 55