light OPEL ASTRA SALOON 2014 Repair Manual

176Vehicle care
5. Press out six locking catches onthe bulb housing and remove bulb
carrier.
6. Remove and renew the bulb.
Brake light ( 1)
Reverse light ( 2)
Fog light, may be only on one side
( 3 )
Turn signal light ( 4)
Reverse light ( 5)
7. Engage bulb holder in bulb
housing. Ensure the seal is
applied correctly and the carrier
has engaged properly.
8. Attach the plug connector. Place bulb housing in body, clipping the
round- head bolts into the
recesses. Attach bulb housing to
the body with four screws. Close
cover and lock.
Station wagon, Van
1. Disengage cover by pressing retaining lugs and remove.
2. Detach plug connector from bulbholder.
3. Loosen fastening nuts and remove the bulb housing
rearwards.

Vehicle care177
4. Unscrew the three screws with ascrewdriver and remove the bulb
holder. Vehicle tools 3 187.
5. Remove and renew the bulb.
Reverse light/brake light ( 1)
Turn signal light ( 2)
Reverse light ( 3)
Fog light, may be only on one side
( 4 )
6. Engage bulb holder in bulb housing and screw in place. Insertthe bulb housing into the body andtighten the fastening nuts by
hand.
Attach the plug connector.
Close and engage the cover.
TwinTop1. Unscrew retaining nuts.
2. Remove bulb housing from outside. Disengage plug by
pressing on flap and remove from
bulb holder.
3. Detach seal from bulb holder.

178Vehicle care
4.Disengage sockets by turning and
remove. Press locking tabs on thelong sides of the bulb holder
outwards; lift bulb holder at front end and remove.5. Remove and renew the bulb.
Reverse light/brake light ( 1)
Reverse light ( 2)
Fog light, may be only on one side
( 3 )
Reverse light ( 4)
Turn signal light ( 5)
6. Insert bulb holder in bulb housing by first inserting the lug at the front
of the plug. Fold together bulb
holder, ensuring that it engages
properly. Insert sockets and
engage by turning.7. Fit seal on bulb holder. Ensure that the seal is flat in the area of
the screws.
8. Engage plug. Insert bulb housing in body, ensuring proper
positioning of the ball pins in the
recesses. Tighten the retaining
nuts.
Side turn signal lights
Have the bulbs replaced by a
workshop.

Vehicle care179Number plate light
1. Insert a screwdriver in thehousing, press to the side and
release spring.
2. Remove bulb housing downwards, taking care not to pull
on the cable.
3. Lift flap and disconnect wiring plug from bulb holder.4. Rotate bulb holder anti-clockwiseto disengage.
5. Remove bulb from holder and renew bulb.
6. Insert bulb holder in bulb housing and rotate clockwise.
7. Connect wiring plug to bulb holder.
8. Insert and engage bulb housing.

180Vehicle careInterior lightsFront courtesy light, reading
lights
1. Disengage lens, press it slightly downwards and remove at a
downward angle.
2. Remove bulb and renew.
3. Engage lens.
Rear courtesy light and reading
lights
Have bulbs replaced by a workshop.
Glovebox light, load
compartment light, foot well light
1. Prise the lamp out with a screwdriver.
2.Press bulb slightly towards spring
clip and remove.
3. Insert new bulb.
4. Install lamp.
Instrument panel
illumination
Have bulbs replaced by a workshop.

Vehicle care183
Fuse assignments inconjunction with loadcompartment fuse box version ANo.Circuit1ABS2ABS3Interior fan climate control
system4Interior fan, heating, air condi‐
tioning system5Radiator fan6Radiator fan7Central locking system8Windscreen washer system,
tailgate9Heated rear window, heated
exterior mirror10Diagnostics plug11InstrumentsNo.Circuit12Mobile telephone, Infotainment
system, display13Courtesy light14Windscreen wiper15Windscreen wiper16Horn, ABS, brake light switch,
air conditioning system17Diesel fuel filter or air condi‐
tioning system18Starter19–20Horn21Engine electronics22Engine electronics23Headlight range adjustment24Fuel pump25–26Engine electronicsNo.Circuit27Heating, air conditioning system28–29Power steering30Engine electronics31Rear window wiper32Brake light switch33Headlight range adjustment,
light switch, clutch switch,
instrument, driver's door
module34Control unit, steering column
module35Infotainment system36Cigarette lighter, front power
outlet

184Vehicle care
Fuse assignments inconjunction with load
compartment fuse box version BNo.Circuit1ABS2ABS3Interior fan electronic climate control4Interior fan heating and air
conditioning system5Radiator fan6Radiator fan7Windscreen washer system8Horn9Headlight washer system10–11–12–13Fog lightNo.Circuit14Windscreen wiper15Windscreen wiper16Control module electronics,
Open&Start system, ABS,
brake light switch, TwinTop17Diesel fuel filter heating18Starter19Transmission electronics20Air conditioning system21Engine electronics22Engine electronics23Adaptive forward lighting, head‐
light range adjustment24Fuel pump25Transmission electronics26Engine electronics27Power steering28Transmission electronicsNo.Circuit29Transmission electronics30Engine electronics31Adaptive forward fighting, head‐ light range adjustment32Brake system, air conditioning
system, clutch switch33Adaptive forward lighting, head‐
light range adjustment, light
switch34Control unit, steering column
module35Infotainment system36Mobile telephone, Infotainment
system, display

Vehicle care185Load compartment fuse
box
The fuse box is behind a cover.
Do not store any objects behind the
cover.
Depending on the equipment, there
are two different fuse boxes.
Saloon 5-door, Station wagon,
Van
To open, turn both catches with a coin
and fold down cover .
Saloon 3-door
To open, fold the cover upwards.
Saloon 4-door
To open, twist catch anti-clockwise
and fold down cover .
TwinTop
To open, pull the two knobs, remove
the clips and fold the cover upwards.
Fuse box version A
To replace a fuse, remove the
relevant protective cap.
No.Circuit1Fog light2–3Load compartment power outlet4Reversing lights5Rear power windows6Air conditioning system7Front power windows8Heated exterior mirrors

Vehicle care187
No.Circuit29Cigarette lighter, front power
outlet30Rear power outlet31–32–33Open&Start system34Sun roof, TwinTop35Rear power outlet36Socket for towing equipment37–38Central locking system, terminal
3039Left seat heating40Right seat heating41–42–No.Circuit43–44–Vehicle tools
Tools
Vehicles with tyre repair set
The tool kit and tyre repair set are in
a storage compartment below the
floor cover in the load compartment.
Vehicles with spare wheel
The jack and tool kit are in a stowage
compartment in the boot below the
spare wheel. Spare wheel 3 198

Vehicle care195
6.Unscrew valve cap from defective
tyre.
7. Screw tyre inflation hose to valve.
8. The switch on the compressor must be set to §.
9. Connect the compressor plug to the accessory socket or cigarette
lighter socket.
To avoid discharging the battery,
we recommend running the
engine.10. Set the rocker switch on the compressor to I. The tyre is filled
with sealant.
11. The compressor pressure gauge briefly indicates up to 6 bar whilstthe sealant bottle is emptying
(approx. 30 seconds). Then the
pressure starts to drop.
12. All of the sealant is pumped into the tyre. Then the tyre is inflated.13. The prescribed tyre pressureshould be obtained within
10 minutes. Tyre pressure
3 225 . When the correct pressure
is obtained, switch off the
compressor.
If the prescribed tyre pressure is
not obtained within 10 minutes,
remove the tyre repair kit. Move
the vehicle one tyre rotation.
Reattach the tyre repair kit and
continue the filling procedure for 10 minutes. If the prescribed tyre
pressure is still not obtained, the
tyre is too badly damaged. Seek
the assistance of a workshop.