parking brake OPEL CASCADA 2018.5 Manual user

208Vehicle careNo.Circuit1Engine control module2Lambda sensor3Fuel injection, ignition system4Fuel injection, ignition system5–6Mirror heating7Fan control8Lambda sensor, engine cooling9Rear window sensor10Vehicle battery sensor11Trunk release12Adaptive forward lighting, auto‐
matic light control13ABS Valves14–15Engine control module16Starter17Transmission control moduleNo.Circuit18Heated rear window19Front power windows20Rear power windows21Rear electrical centre22Left high beam (Halogen)23Headlamp washer system24Right low beam (Xenon)25Left low beam (Xenon)26Front fog lights27Diesel fuel heating28Start stop system29Electric parking brake30ABS pump31–32Airbag33Adaptive forward lighting, auto‐
matic light control34Exhaust gas recirculationNo.Circuit35Power windows, rain sensor,
exterior mirror36Climate control37–38Vacuum pump39Fuel system control module40Windscreen washer system41Right high beam (Halogen)42Radiator fan43Windscreen wiper44–45Radiator fan46–47Horn48Radiator fan49Fuel pump50Headlamp levelling, adaptive
forward lighting

Vehicle care215If w illuminates at lower temperatures
and extinguishes after driving, this
could be an indicator for approaching
a low tyre pressure condition. Check
tyre pressure.
Vehicle messages 3 103.
If the tyre pressure must be reduced
or increased, switch off ignition.
Only mount wheels with pressure
sensors, otherwise the tyre pressure
will not be displayed and w
illuminates continuously.
A spare wheel or temporary spare
wheel is not equipped with pressure
sensors. The tyre pressure
monitoring system is not operational
for these tyres. Control indicator w
illuminates. For the further three
wheels the system remains
operational.
The use of commercially-available
liquid tyre repair kits can impair the
function of the system. Factory-
approved repair kits can be used.
Operating electronic devices or being close to facilities using similar wave
frequencies could disrupt the tyre
pressure monitoring system.Each time the tyres are replaced, tyre pressure sensors must be
dismounted and serviced. For the
screwed sensor: replace valve core
and sealing ring. For clipped sensor:
replace complete valve stem.
Vehicle loading status Adjust tyre pressure to load condition
according to the tyre information label or tyre pressure chart 3 248, and
select the appropriate setting in the Tyre load menu in the Driver
Information Centre 3 96. This setting
is the reference for the tyre pressure
warnings.
The menu Tyre Load only appears if
the vehicle is at a standstill and the
parking brake is applied. On vehicles
with automatic transmission, the
selector lever must be in P.
Select:
● Light for comfort pressure up to
3 people
● Eco for Eco pressure up to
3 people
● Max for full loading
Tyre pressure sensor matching
process
Each tyre pressure sensor has a
unique identification code. The
identification code must be matched
to a new wheel position after rotating
the wheels or exchanging the
complete wheel set and if one or more
tyre pressure sensors were replaced.

216Vehicle careThe tyre pressure sensor matchingprocess should also be performed
after replacing a spare wheel with a
road wheel containing a tyre pressure sensor.
The malfunction light w and the
warning message or code should extinguish at the next ignition cycle. The sensors are matched to the
wheel positions using a relearn tool,
in the following order: left side front
wheel, right side front wheel, right
side rear wheel and left side rear
wheel. The turn signal light at the
current active position is illuminated
until the sensor is matched.
Consult your workshop for service.
There are two minutes to match the first wheel position, and five minutes
overall to match all four wheel
positions. If it takes longer, the
matching process stops and must be restarted.
The tyre pressure sensor matching
process is as follows:
1. Apply the parking brake.
2. Turn the ignition on.3. On vehicles with automatic transmission: set the selector
lever to P.
On vehicles with manual
transmission: select neutral.
4. Use MENU on the turn signal
lever to select the Vehicle
Information Menu in the Driver
Information Centre.
5. Turn the adjuster wheel to scroll to
the tyre pressure menu.
6. Press SET/CLR to begin the
sensor matching process. A
message requesting acceptance
of the process should be
displayed.
7. Press SET/CLR again to confirm
the selection. The horn sounds
twice to indicate that the receiver
is in relearn mode.
8. Start with the left side front wheel.
9. Place the relearn tool against the tyre sidewall, near the valve stem.Then press the button to activatethe tyre pressure sensor. A horn
chirp confirms that the sensor
identification code has been
matched to this wheel position.10. Proceed to the right side front wheel, and repeat the procedure
in Step 9.
11. Proceed to the right side rear wheel, and repeat the procedure
in Step 9.
12. Proceed to the left side rear wheel, and repeat the procedure
in Step 9. The horn sounds twice
to indicate the sensor
identification code has been
matched to the left side rear tyre,
and the tyre pressure sensor
matching process is no longer
active.
13. Turn off the ignition.
14. Set all four tyres to the recommended tyre pressure as
indicated on the tyre pressure
information label.
15. Ensure the tyre loading status is set according to the selected
pressure 3 96.

Vehicle care219Wheel covers
Wheel covers and tyres that are
factory approved for the respective
vehicle and comply with all of the
relevant wheel and tyre combination
requirements must be used.
If the wheel covers and tyres used are
not factory approved, the tyres must
not have a rim protection ridge.
Wheel covers must not impair brake
cooling.9 Warning
Use of unsuitable tyres or wheel
covers could lead to sudden
pressure loss and thereby
accidents.
Vehicles with steel wheels: When
using locking wheel nuts, do not
attach wheel covers.
Tyre chains
Use tyre chains only on front wheels.
Always use fine mesh chains that add no more than 10 mm to the tyre tread
and the inboard sides (including chain
lock).
9 Warning
Damage may lead to tyre blowout.
Tyre chains are permitted on tyres of
sizes 225/55 R17 and 245/45 R18.
The use of tyre chains is not permitted on the temporary spare wheel.
Tyre repair kit
Minor damage to the tyre tread can be
repaired with the tyre repair kit.
Do not remove foreign bodies from
the tyres.
Tyre damage exceeding 4 mm or that
is at tyre's sidewall cannot be repaired with the tyre repair kit.9 Warning
Do not drive faster than 80 km/h.
Do not use for a lengthy period.
Steering and handling may be
affected.
If you have a flat tyre:
Apply the parking brake and engage
first gear, reverse gear or P.

Vehicle care223Make the following preparations and
observe the following information:
● Park the vehicle on a level, firm and non-slippery surface. The
front wheels must be in the
straight-ahead position.
● Apply the parking brake and engage first gear, reverse gear or
P .
● Remove the spare wheel 3 225.
● Never change more than one wheel at once.
● Use the jack only to change wheels in case of puncture, not
for seasonal winter or summer
tyre change.
● The jack is maintenance-free. ● If the ground on which the vehicle
is standing is soft, a solid board
(max. 1 cm thick) should be
placed under the jack.
● Remove heavy objects from the vehicle before jacking up.
● No people or animals may be in the vehicle when it is jacked-up.
● Never crawl under a jacked-up vehicle.●Do not start the vehicle when it is
raised on the jack.
● Clean wheel nuts and thread with
a clean cloth before mounting the wheel.9 Warning
Do not grease wheel bolt, wheel
nut and wheel nut cone.
1. Disengage wheel nut caps with a
screwdriver and remove. Pull off
the wheel cover. Vehicle tools
3 212.
Alloy wheels: Disengage wheel
nut caps with a screwdriver and
remove. To protect the wheel,
place a soft cloth between the
screwdriver and the alloy wheel.Alloy wheels with centre wheel
bolt cap: Disengage centre cap by
inserting and pulling the extractor
3 212 in the recess of the brand
emblem.

Vehicle care229● A discharged vehicle battery canalready freeze at a temperature
of 0 °C. Defrost the frozen battery before connecting jump leads.
● Wear eye protection and protective clothing when
handling a battery.
● Use a booster battery with the same voltage (12 Volts). Its
capacity (Ah) must not be much
less than that of the discharged
battery.
● Use jump leads with insulated terminals and a cross section of
at least 16 mm 2
(25 mm 2
for
diesel engines).
● Do not disconnect the discharged
battery from the vehicle.
● Switch off all unnecessary electrical consumers.
● Do not lean over the battery during jump starting.
● Do not allow the terminals of one
lead to touch those of the other
lead.
● The vehicles must not come into contact with each other during
the jump starting process.● Apply the parking brake, transmission in neutral,
automatic transmission in P.
● Open the positive terminal protection caps of both batteries.
Lead connection order:
1. Connect the red lead to the positive terminal of the booster
battery.
2. Connect the other end of the red lead to the positive terminal of the
discharged battery.
3. Connect the black lead to the negative terminal of the booster
battery.
4. Connect the other end of the black
lead to a vehicle grounding point,
such as the engine block or an
engine mounting bolt. Connect as far away from the discharged
battery as possible, however at
least 60 cm.
Route the leads so that they cannot
catch on rotating parts in the engine
compartment.
To start the engine: 1. Start the engine of the vehicle providing the jump.
2. After 5 minutes, start the other engine. Start attempts should be
made for no longer than
15 seconds at an interval of
1 minute.
3. Allow both engines to idle for approx. 3 minutes with the leads
connected.

230Vehicle care4. Switch on electrical consumers(e.g. headlights, heated rear
window) of the vehicle receiving
the jump start.
5. Reverse above sequence exactly when removing leads.Towing
Towing the vehicle
Wrap a cloth around the tip of a flat
screwdriver to prevent paint damage.
Insert the screwdriver in the slot at the
lower part of the cap. Release the cap by carefully moving the screwdriver
downwards.
The towing eye is stowed with the
vehicle tools 3 212.
Screw in the towing eye anticlockwise
as far as it will go until it stops in a
horizontal position.
Attach a tow rope – or better still a tow
rod – to the towing eye.
The towing eye must only be used for
towing and not for recovering the
vehicle.
Switch on ignition to release steering wheel lock and to permit operation of
brake lights, horn and windscreen
wiper.
Switch the selector lever to neutral.
Release the parking brake.

261Clock............................................. 82
Code ........................................... 103
Control indicators.......................... 88
Control of the vehicle .................138
Controls ........................................ 79
Convex shape .............................. 30
Coolant and antifreeze ...............236
Cruise control ...................... 96, 159
Cupholders .................................. 71
Curve lighting.............................. 118
D
Danger, Warnings and Cautions ...4
Daytime running lights ...............118
Declaration of conformity ............250
DEF ............................................ 145
Diesel exhaust fluid ....................145
Diesel fuel system bleeding .......197
Door open .................................... 96
Doors ............................................ 26
Driver assistance systems ..........159
Driver Information Centre .............96
Driving characteristics and towing tips .............................. 185
Driving hints ................................ 138
E Electric adjustment ......................30
Electrical system......................... 206
Electric parking brake ...........92, 153
Electric parking brake fault ...........93Electronic climate control system 130
Electronic driving programmes ..150
Electronic Stability Control.......... 156
Electronic Stability Control and Traction Control system ............94
Electronic Stability Control off....... 94
End-of-life vehicle recovery .......192
Engine compartment fuse box ...207
Engine coolant ........................... 194
Engine coolant temperature gauge ....................................... 86
Engine data ............................... 244
Engine exhaust .......................... 144
Engine identification ...................240
Engine oil ................... 193, 236, 241
Engine oil pressure ......................95
Entry lighting .............................. 125
Event data recorders ..................256
Exhaust filter ......................... 94, 144
Exit lighting ................................ 125
Exterior care .............................. 232
Exterior light ................................. 95
Exterior lighting ....................14, 114
Exterior mirrors ............................. 30
F
Fault ........................................... 151
First aid ......................................... 76
First aid kit ................................... 76
Fixed air vents ........................... 135Fog light ....................................... 96
Fog lights ................................... 201
Folding mirrors ............................. 31
Following distance indication ......164
Forward collision alert................. 162
Front airbag system .....................62
Front fog lights ........................... 122
Front seats.................................... 49
Front storage ................................ 71
Front turn lights .......................... 202
Fuel............................................. 180
Fuel for diesel engines ..............182
Fuel for petrol engines ...............180
Fuel gauge ................................... 86 Funnel......................................... 182
Fuses ......................................... 206
G Gauges ......................................... 85
General information ...................185
Glovebox ..................................... 70
Ground clearance .......................138
H Halogen headlights ....................198
Hand brake ......................... 152, 153
Hazard warning flashers ............121
Headlight flash ........................... 117
Headlight range adjustment ......117
Headlights................................... 114
Headlights when driving abroad 117

262Head restraint adjustment .............8
Head restraints ............................ 47
Heated mirrors ............................. 31
Heated rear window ..................... 35
Heated steering wheel .................79
Heating ........................................ 55
Heating and ventilation system . 127
High beam ........................... 95, 116
High beam assist ..................96, 116
Hill start assist ........................... 155
Horn ....................................... 15, 80
I
Identification plate .....................239
Ignition switch positions .............139
Immobiliser ............................ 30, 95
Indicators ...................................... 85
Info Display ................................. 101
Information displays...................... 96
Instrument cluster ........................85
Instrument panel fuse box .........209
Instrument panel illumination .....206
Instrument panel illumination control .................................... 123
Instrument panel overview ........... 10
Interactive driving system ...........157
Interior care ............................... 234
Interior lighting ............................ 123
Interior lights ...................... 124, 206
Interior mirrors .............................. 32Interruption of power supply ......151
Introduction .................................... 3
J Jump starting ............................. 228
K Key, memorised settings ..............23
Keys ............................................. 21
Keys, locks ................................... 21
L Lane departure warning .......93, 179
Lashing eyes ............................... 76
Light switch ................................ 114
Load compartment ................26, 73
Load compartment fuse box ......210
Loading information .....................77
Low fuel ....................................... 95
M Malfunction indicator light ............92
Manual anti-dazzle ......................32
Manual mode ............................. 150
Manual seat adjustment ...............50
Manual transmission .................. 152
Memorised settings ......................23
Mirror adjustment ........................... 8 Misted light covers .....................123N
New vehicle running-in ..............139
Number plate light .....................205
O Object detection systems ...........165
Odometer ..................................... 85
Oil, engine .......................... 236, 241
OnStar ........................................ 109
Operate pedal ............................... 92
Outside temperature ....................81
Overrun cut-off ........................... 140
P
Parking ................................ 19, 142
Parking assist ............................ 165
Parking brake ............................ 153
Parking lights ............................. 123
Particulate filter ........................... 144
Performance .............................. 245
Performing work ........................192
Pollen filter ................................. 135
Power outlets ............................... 83
Power seat adjustment ................53
Power steering.............................. 93
Power windows ............................ 33
Preheating ................................... 94
Puncture ..................................... 222
Q Quickheat ................................... 134