manual transmission OPEL CASCADA 2018 Manual user

Driving and operating149KickdownIf the accelerator pedal is pressed
down completely in automatic mode,
the transmission shifts to a lower gear
depending on engine speed.
Fault
In the event of a fault, a vehicle message is displayed in the Driver
Information Centre. Vehicle
messages 3 101.
The transmission no longer shifts automatically. Continued travel is
possible with manual shifting.
Only the highest gear is available.
Depending on the fault, 2nd gear may also be available in manual mode.
Shift only when vehicle is at a
standstill.
Have the cause of the fault remedied by a workshop.Interruption of power supply
In the event of an interruption of
power supply, the selector lever
cannot be moved out of the P
position. The ignition key cannot be removed from the ignition switch.
If the vehicle battery is discharged,
start the vehicle using jump leads
3 226.
If the vehicle battery is not the cause
of the fault, release the selector lever.
1. Apply the parking brake.
2. Release the selector lever trim from the centre console at the
front, fold it upwards and rotate it
to the left.
3. Insert a screwdriver into the opening as far as it will go and
move the selector lever out of P or
N . If P or N is engaged again, the
selector lever will be locked in
position again. Have the cause of
the power supply interruption
remedied by a workshop.
4. Mount the selector lever trim onto
the centre console and refit.

150Driving and operatingManual transmission
To engage reverse, with the vehicle
stationary, depress clutch pedal,
press the release button on the
selector lever and engage the gear.
If the gear does not engage, set the
lever to neutral, release the clutch
pedal and depress again; then repeat
gear selection.
Do not slip the clutch unnecessarily.
When operating, depress the clutch
pedal completely. Do not use the
pedal as a foot rest.
Caution
It is not advisable to drive with the hand resting on the selector lever.
Upshift indication 3 91.
Brakes
The brake system comprises two independent brake circuits.
If a brake circuit fails, the vehicle can
still be braked using the other brake
circuit. However, braking effect is
achieved only when the brake pedal
is depressed firmly. Considerably
more force is needed for this. The
braking distance is extended. Seek
the assistance of a workshop before
continuing your journey.
When the engine is not running, the
support of the brake servo unit
disappears once the brake pedal has
been depressed once or twice.
Braking effect is not reduced, but
braking requires significantly greater
force. It is especially important to bear this in mind when being towed.
Control indicator R 3 90.
Antilock brake system
Antilock brake system (ABS)
prevents the wheels from locking.

152Driving and operatingTo reduce the operating forces ofthe parking brake, depress the
brake pedal at the same time.
Control indicator R 3 90.
Electric parking brake
Applying when vehicle is stationary
9 Warning
Pull switch m for approx.
one second, the electric parking
brake operates automatically with
adequate force. For maximum
force, e.g. parking with trailer or on
inclines, pull switch m twice.
The electric parking brake is
applied when control indicator m
illuminates 3 91.
The electric parking brake can always
be activated, even if the ignition is off.
Do not operate electric parking brake
system too often without engine
running as this will discharge the
vehicle battery.
Before leaving the vehicle, check the electric parking brake status. Control
indicator m 3 91.
Releasing
Switch on ignition. Keep brake pedal
depressed then push switch m.
Drive away function
Vehicles with manual transmission:
Depressing the clutch pedal and then
slightly releasing the clutch pedal and
slightly depressing the accelerator
pedal releases the electric parking
brake automatically. This is not
possible when the switch m is pulled
at the same time.
Vehicles with automatic transmission: Engaging D and then depressing the
accelerator pedal releases the
electric parking brake automatically. This is not possible when the switch
m is pulled at the same time.
Dynamic braking when vehicle is
moving
When the vehicle is moving and the
switch m is kept pulled, the electric
parking brake system will decelerate
the vehicle, but will not apply
statically.
As soon as the switch m is released,
dynamic braking will be stopped.
Fault
Failure mode of electric parking brake
is indicated by control indicator j and
by a vehicle message which is
displayed in the Driver Information
Centre.

214Vehicle careThe tyre pressure sensor matchingprocess should also be performed
after replacing a spare wheel with a
road wheel containing a tyre pressure sensor.
The malfunction light w and the
warning message or code should extinguish at the next ignition cycle. The sensors are matched to the
wheel positions using a relearn tool,
in the following order: left side front
wheel, right side front wheel, right
side rear wheel and left side rear
wheel. The turn signal light at the
current active position is illuminated
until the sensor is matched.
Consult your workshop for service.
There are two minutes to match the first wheel position, and five minutes
overall to match all four wheel
positions. If it takes longer, the
matching process stops and must be restarted.
The tyre pressure sensor matching
process is as follows:
1. Apply the parking brake.
2. Turn the ignition on.3. On vehicles with automatic transmission: set the selector
lever to P.
On vehicles with manual
transmission: select neutral.
4. Use MENU on the turn signal
lever to select the Vehicle
Information Menu in the Driver
Information Centre.
5. Turn the adjuster wheel to scroll to
the tyre pressure menu.
6. Press SET/CLR to begin the
sensor matching process. A
message requesting acceptance
of the process should be
displayed.
7. Press SET/CLR again to confirm
the selection. The horn sounds
twice to indicate that the receiver
is in relearn mode.
8. Start with the left side front wheel.
9. Place the relearn tool against the tyre sidewall, near the valve stem.Then press the button to activatethe tyre pressure sensor. A horn
chirp confirms that the sensor
identification code has been
matched to this wheel position.10. Proceed to the right side front wheel, and repeat the procedure
in Step 9.
11. Proceed to the right side rear wheel, and repeat the procedure
in Step 9.
12. Proceed to the left side rear wheel, and repeat the procedure
in Step 9. The horn sounds twice
to indicate the sensor
identification code has been
matched to the left side rear tyre,
and the tyre pressure sensor
matching process is no longer
active.
13. Turn off the ignition.
14. Set all four tyres to the recommended tyre pressure as
indicated on the tyre pressure
information label.
15. Ensure the tyre loading status is set according to the selected
pressure 3 95.

Technical data243Sales designation2.0 CDTI2.0 CDTIEngine identifier codeA20DTHB20DTHEngineering codeA20DTHB20DTHPiston displacement [cm3
]19561956Engine power [kW]121125at rpm40003750Torque [Nm]350400at rpm1750-25001750-2500Fuel typeDieselDieselPerformanceEngineB14NELB14NETA16XHTB16SHTB16SHLMaximum speed [km/h]Manual transmission195207222235–Automatic transmission––––219

244Technical dataEngineA20DTHB20DTHMaximum speed [km/h]Manual transmission218218Automatic transmission212–

Technical data245Vehicle weightKerb weight, basic model without any optional equipmentEngineManual transmissionAutomatic transmissionwithout/with air conditioning
[kg]B14NEL1701/1714–B14NET1701/1714–A16XHT–/1733–B16SHT–/1733–B16SHL––/1733A20DTH–/1816–/1816B20DTH–/1843–
Optional equipment and accessories increase the kerb weight.
Loading information 3 77.

262Hazard warning flashers ............119
Headlight flash ........................... 115
Headlight range adjustment ......115
Headlights................................... 112
Headlights when driving abroad 115
Head restraint adjustment .............8
Head restraints ............................ 47
Heated mirrors ............................. 31
Heated rear window ..................... 35
Heated steering wheel .................79
Heating ........................................ 55
Heating and ventilation system . 125
High beam ........................... 94, 114
High beam assist ..................94, 114
Hill start assist ........................... 153
Horn ....................................... 15, 80
I
Identification plate .....................237
Ignition switch positions .............137
Immobiliser ............................ 30, 94
Indicators ...................................... 85
Information displays...................... 95
Instrument cluster ........................85
Instrument panel fuse box .........207
Instrument panel illumination .....204
Instrument panel illumination control .................................... 121
Instrument panel overview ........... 10
Interactive driving system ...........155Interior care ............................... 232
Interior lighting ............................ 121
Interior lights ...................... 122, 204
Interior mirrors .............................. 32
Interruption of power supply ......149
Introduction .................................... 3
J Jump starting ............................. 226
K Key, memorised settings ..............23
Keys ............................................. 21
Keys, locks ................................... 21
L
Lane departure warning .......92, 177
Lashing eyes ............................... 76
Light switch ................................ 112
Load compartment ................26, 73
Load compartment fuse box ......208
Loading information .....................77
Low fuel ....................................... 94
M Malfunction indicator light ............90
Manual anti-dazzle ......................32
Manual mode ............................. 148
Manual seat adjustment ...............50
Manual transmission .................. 150
Memorised settings ......................23Mirror adjustment ........................... 8
Misted light covers .....................121
N
New vehicle running-in ..............137
Number plate light .....................203
O Object detection systems ...........163
Odometer ..................................... 85
Oil, engine .......................... 234, 239
OnStar ........................................ 107
Operate pedal ............................... 90
Outside temperature ....................81
Overrun cut-off ........................... 138
P Parking ................................ 19, 140
Parking assist ............................ 163
Parking brake ............................ 151
Parking lights ............................. 121
Particulate filter ........................... 142
Performance .............................. 243
Performing work ........................190
Pollen filter ................................. 133
Power outlets ............................... 83
Power seat adjustment ................53
Power steering.............................. 92
Power windows ............................ 33
Preheating ................................... 92
Puncture ..................................... 220