display OPEL CORSA E 2019 Manual user

Vehicle care181Midlevel display:
The tyre pressure for each tyre is
displayed on its own page.
Uplevel display:
The tyre pressures for all tyres are
displayed on one page.
System status and pressure warnings
are displayed by a message
indicating the corresponding tyre in the Driver Information Centre.
The system considers the tyre
temperature for the warnings.
Temperature dependency 3 179.
A detected low tyre pressure
condition is indicated by the control
indicator w 3 81.
If w illuminates, stop as soon as
possible and inflate the tyres as
recommended 3 214.
If w flashes for 60-90 seconds then
illuminates continuously, there is a
fault in the system. Consult a
workshop.
After inflating, some driving may be
required to update the tyre pressure
values in the Driver Information
Centre. During this time w may
illuminate.
If w illuminates at lower temperatures
and extinguishes after driving, this
could be an indicator for approaching a low tyre pressure condition. Check
tyre pressure.
Vehicle messages 3 89.
If the tyre pressure must be reduced
or increased, switch off ignition.
Only mount wheels with pressure
sensors, otherwise the tyre pressure
will not be displayed and w
illuminates continuously.
A spare wheel or temporary spare
wheel is not equipped with pressure
sensors. The tyre pressure
monitoring system is not operational
for these tyres. Control indicator w
illuminates. For the further three
tyres, the system remains
operational.

182Vehicle careThe use of commercially-availableliquid tyre repair kits can impair the
function of the system. Factory-
approved repair kits can be used.
Operating electronic devices or being close to facilities using similar wave
frequencies could disrupt the tyre
pressure monitoring system.
Each time the tyres are replaced, tyre
pressure monitoring system sensors
must be dismounted and serviced. For the screwed sensor; replace
valve core and sealing ring. For the
clipped sensor; replace complete
valve stem.
Vehicle loading status
Adjust tyre pressure to load condition according to the tyre information labelor tyre pressure chart 3 214, and
select the appropriate setting in the menu Tyre Load in the Driver
Information Centre, Vehicle
Information Menu 3 83 . This setting is
the reference for the tyre pressure
warnings.
The menu Tyre Load only appears
when the vehicle is at a standstill and
the parking brake is applied.On vehicles with automatic
transmission, the selector lever must
be in P.
Midlevel display:
Select ● LO for comfort pressure up to
three people.
● ECO for Eco pressure up to three
people.
● Hi for full loading.
Uplevel display:
Select ● Light for comfort pressure up to
three people.
● Eco for Eco pressure up to three
people.
● Max for full loading.
Tyre pressure sensor matching
process
Each pressure sensor has a unique identification code. The identification
code must be matched to a new
wheel position after rotating the
wheels or exchanging the complete
wheel set and if one or more tyre
pressure sensors were replaced. The

Vehicle care183tyre pressure sensor matching
process should also be performed
after replacing a spare wheel with a
road wheel containing a tyre pressure
sensor.
The malfunction light w and the
warning message or code should
extinguish at the next ignition cycle. The sensors are matched to the
wheel positions, using a relearn tool,
in the following order: left side front
wheel, right side front wheel, right
side rear wheel and left side rear
wheel. The turn light at the current
active position is illuminated until
sensor is matched.
Consult a workshop for service. There
are 2 minutes to match the first wheel position, and 5 minutes overall to
match all four wheel positions. If it
takes longer, the matching process
stops and must be restarted.
The tyre pressure sensor matching
process is:
1. Apply the parking brake.
2. Turn the ignition on.3. On vehicles with automatic transmission: set the selector
lever to P.
On vehicles with manual
transmission: select neutral.
4. Use MENU on the stalk to select
the Vehicle Information
Menu ? in the Driver
Information Centre.
5. Turn the adjuster wheel to scroll to
the tyre pressure menu.
Midlevel display:
Uplevel display:
6. Press SET/CLR to begin the
sensor matching process. A
message requesting acceptance
of the process should be
displayed.
7. Press SET/CLR again to confirm
the selection. The horn sounds
twice to indicate that the receiver
is in relearn mode.
8. Start with the left side front wheel.
9. Place the relearn tool against the tyre sidewall, near the valve stem.Then press the button to activate
the tyre pressure sensor. A horn
chirp confirms that the sensor
identification code has been
matched to this wheel position.

Vehicle care201Clean the leather upholstery with
clear water and a soft cloth. In case of
heavy soiling, use leather care.
The instrument cluster and the
displays should only be cleaned using
a soft damp cloth. If necessary use a
weak soap solution.
Clean fabric upholstery with a
vacuum cleaner and brush. Remove
stains with an upholstery cleaner.
Clothing fabrics may not be
colourfast. This could cause visible
discolourations, especially on light- coloured upholstery. Removable
stains and discolourations should be
cleaned as soon as possible.
Clean seat belts with lukewarm water or interior cleaner.Caution
Close Velcro fasteners as open
Velcro fasteners on clothing could damage seat upholstery.
The same applies to clothing with
sharp-edged objects, like zips or
belts or studded jeans.
Plastic and rubber parts
Plastic and rubber parts can be
cleaned with the same cleaner as
used to clean the body. Use interior cleaner if necessary. Do not use any
other agent. Avoid solvents and petrol in particular. Do not use high-
pressure jet cleaners.

202Service and maintenanceService and
maintenanceGeneral information ...................202
Service information ..................202
Recommended fluids, lubricants
and parts .................................... 203
Recommended fluids and lubricants ................................ 203General information
Service information In order to ensure economical and
safe vehicle operation and to
maintain the value of your vehicle, it
is of vital importance that all
maintenance work is carried out at the proper intervals as specified.
The detailed, up-to-date service
schedule for your vehicle is available
at the workshop.
Service display 3 74.
European service intervals
Maintenance of your vehicle is
required every 30,000 km or after one year, whichever occurs first.
Additional engine oil and filter change
is indicated by the engine oil life
system, when required earlier than
maintenance.
A shorter service interval can be valid for severe driving behaviour, e.g. for
taxis and police vehicles.
The European service intervals are
valid for the following countries:Andorra, Austria, Belgium, Bosnia-
Herzegovina, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany,
Greece, Greenland, Hungary,
Iceland, Ireland, Italy, Latvia,
Liechtenstein, Lithuania,
Luxembourg, Macedonia, Malta,
Monaco, Montenegro, Netherlands,
Norway, Poland, Portugal, Romania, San Marino, Serbia, Slovakia,
Slovenia, Spain, Sweden,
Switzerland, United Kingdom.
Service display 3 74.
International service intervals
Maintenance of your vehicle is
required every 15,000 km or after one year, whichever occurs first.
Additional engine oil and filter change
is indicated by the engine oil life
system, when required earlier than
maintenance.
Severe operating conditions exist if
one or more of the following
circumstances occur frequently: Cold
starting, stop and go operation, trailer operation, mountain driving, driving
on poor and sandy road surfaces,

Service and maintenance203increased air pollution, presence of
airborne sand and high dust content,
driving at high altitude and large
variations of temperature. Under
these severe operating conditions,
certain service work may be required more frequently than the regularservice interval.
The international service intervals are
valid for the countries which are not
listed in the European service
intervals.
Service display 3 74.
Confirmations
Confirmation of service is recorded in the Service and Warranty Booklet.
The date and mileage is completed
with the stamp and signature of the
servicing workshop.
Make sure that the Service and
Warranty Booklet is completed
correctly as continuous proof of
service is essential if any warranty or goodwill claims are to be met, and is
also a benefit when selling the
vehicle.Recommended fluids,
lubricants and parts
Recommended fluids andlubricants
Only use products that meet the
recommended specifications.9 Warning
Operating materials are
hazardous and could be
poisonous. Handle with care. Pay
attention to information given on
the containers.
Engine oil
Engine oil is identified by its quality
and its viscosity. Quality is more
important than viscosity when
selecting which engine oil to use. The oil quality ensures e.g. engine
cleanliness, wear protection and oil
aging control, whereas viscosity
grade gives information on the oil's
thickness over a temperature range.
Dexos is the newest engine oil quality
that provides optimum protection for
petrol engines. If it is unavailable,
engine oils of other listed qualities
have to be used. Recommendations
for petrol engines are also valid for
Compressed Natural Gas (CNG),
Liquified Petroleum Gas (LPG) and
Ethanol (E85) fuelled engines.
Select the appropriate engine oil
based on its quality and on the
minimum ambient temperature
3 207.
Topping up engine oilCaution
In case of any spilled oil, wipe it up and dispose it properly.
Engine oils of different manufacturersand brands can be mixed as long as
they comply with the required engine
oil quality and viscosity.
Use of engine oils for all petrol
engines with only ACEA quality is
prohibited, since it can cause engine
damage under certain operating
conditions.

Customer information221Operating data in the vehicleControl units process data for
operation of the vehicle.
This data includes, e.g.: ● vehicle status information (e.g. speed, movement delay, lateral
acceleration, wheel rotation rate,
"seat belts fastened" display)
● ambient conditions (e.g. temperature, rain sensor,
distance sensor)
As a rule such data is transient, not
stored for longer than an operational
cycle, and only processed on board
the vehicle itself. Control units often
include data storage (including the
vehicle key). This is used to allow
information to be documented
temporarily or permanently on vehicle
condition, component stress,
maintenance requirements and
technical events and errors.Depending on technical equipment
levels, the data stored is as follows:
● system component operating states (e.g. fill level, tyre
pressure, battery status)
● faults and defects in important system components (e.g. lights,brakes)
● system reactions in special driving situations (e.g. triggering
of an airbag, actuation of the
stability control systems)
● information on events damaging the vehicle
● for electric vehicles the amount of
charge in the high-voltage
battery, estimated range
In special cases (e.g. if the vehicle
has detected a malfunction), it may be
necessary to save data that would
otherwise just be volatile.
When you use services (e.g. repairs,
maintenance), the operating data
saved can be read together with the
vehicle identification number and
used where necessary. Staff working
for the service network ( e.g. garages,
manufacturers) or third parties (e.g.breakdown services) can read the
data from the vehicle. The same
applies to warranty work and quality
assurance measures.
Data is generally read via the OBD
(On-Board Diagnostics) port
prescribed by law in the vehicle. The operating datawhich is read out,
documents the technical condition of
the vehicle or individual components
and assists with fault diagnosis,
compliance with warranty obligations
and quality improvement. This data,
in particular information on
component stress, technical events,
operator errors and other faults, is
transmitted to the manufacturer
where appropriate, together with the
vehicle identification number. The
manufacturer is also subject to
product liability. The manufacturer
potentially also uses operating data
from vehicles for product recalls. This
data can also be used to check
customer warranty and guarantee
claims.
Fault memories in the vehicle can be
reset by a service company when
carrying out servicing or repairs or at
your request.

226I
Identification plate .....................206
Ignition switch positions .............120
Immobiliser ............................ 28, 82
Indicators ...................................... 71
Info Display ................................... 88
Information displays...................... 83
Instrument cluster ........................71
Instrument panel fuse box .........175
Instrument panel illumination control .................................... 106
Instrument panel overview ........... 10
Interior care ............................... 200
Interior lighting ............................ 106
Interior lights ...................... 106, 172
Interior mirrors .............................. 30
Interruption of power supply ......129
Introduction .................................... 3
J
Jump starting ............................. 195
K
Key, memorised settings ..............23
Keys ............................................. 21
Keys, locks ................................... 21
L
Lane departure warning .......80, 149
Lashing eyes ............................... 60
Light switch ................................ 100Load compartment ................26, 57
Load compartment cover .............59
Loading information .....................61
Low fuel ....................................... 82
LPG ...................................... 73, 152
M
Malfunction indicator light ............79
Manual anti-dazzle ......................30
Manual mode ............................. 128
Manual transmission .................. 130
Manual windows ..........................31
Memorised settings ......................23
Midlevel display ............................ 83
Mirror adjustment ........................... 8
Misted light covers .....................105
N New vehicle running-in ..............120
Number plate light .....................171
O Object detection systems ...........141
Odometer ..................................... 71
Oil, engine .......................... 203, 207
OnStar .......................................... 95
Operate pedal ............................... 80
Outside temperature ....................67
Overrun cut-off ........................... 122P
Parking ................................ 19, 124
Parking assist ......................80, 141
Parking brake ............................ 132
Parking lights ............................. 105
Particulate filter ........................... 125
Performing work ........................158
Power outlets ............................... 69
Power steering.............................. 80
Power windows ............................ 31
Puncture ..................................... 192
R Radio Frequency Identification (RFID) ..................................... 223
Radio remote control ...................22
REACH ....................................... 218
Reading lights ............................ 107
Rear floor storage cover ..............59
Rear fog light ...............82, 105, 168
Rear view camera ...................... 145
Rear window wiper and washer ..66
Recommended fluids and lubricants ........................ 203, 207
Reduced engine power ................82
Refuelling ................................... 152 Registered trademarks ...............220
Retained power off .....................121
Reversing lights .........................105
Ride control systems ..................133

227Roof load...................................... 61
Roof rack ..................................... 61
S Safety belts ................................... 39
Seat adjustment ....................... 7, 36
Seat belt ........................................ 8
Seat belt reminder .......................78
Seat belts ..................................... 39
Seat folding .................................. 37
Seat heating ................................. 38
Seat position ................................ 35
Selector lever ............................. 127
Service ....................................... 118
Service display ............................ 74
Service information ....................202
Service vehicle soon .................... 79
Side airbag system ......................46
Sidelights .................................... 100
Side turn lights ........................... 170
Software acknowledgement .......218
Spare wheel ............................... 192
Speed limiter......................... 83, 137
Speedometer ............................... 71
Starting and operating ................120
Starting off ................................... 18
Starting the engine ....................121
Steering wheel adjustment ......9, 64
Steering wheel controls ...............64
Stop-start system........................ 122Storage ......................................... 55
Storage compartments .................55
Sun visors .................................... 33
Symbols ......................................... 4
T
Tachometer ................................. 72
Tail lights ................................... 168
Three-point seat belt .................... 40
Tools .......................................... 177
Towing ........................................ 196
Towing another vehicle .............197
Towing the vehicle .....................196
Traction Control system ............. 133
Traffic sign assistant .............83, 146
Transmission ............................... 18
Transmission display .................127
Tread depth ............................... 184
Trip odometer .............................. 71
Turn lights ............................ 77, 104
Tyre chains ................................ 185
Tyre designations ......................178
Tyre pressure ............................ 179
Tyre pressure monitoring system ............................... 81, 180
Tyre pressures ........................... 214
Tyre repair kit ............................. 185
U Underseat storage .......................57
Upholstery .................................. 200Uplevel display............................. 83
Using this manual ..........................3
V Vehicle battery ........................... 162
Vehicle checks............................ 158
Vehicle data ................................ 207
Vehicle data recording and privacy ..................................... 220
Vehicle detected ahead ................83
Vehicle dimensions .................... 212
Vehicle Identification Number ....205
Vehicle jack ................................ 177
Vehicle messages .......................89
Vehicle personalisation ...............92
Vehicle security ............................ 27
Vehicle specific data ......................3
Vehicle storage ........................... 157
Vehicle tools ............................... 177
Vehicle unlocking ........................... 6 Ventilation ................................... 110
W
Warning chimes ........................... 91
Warning lights ............................... 71
Warning triangle .......................... 60
Washer and wiper systems .........16
Washer fluid ............................... 161
Wheel changing .........................191
Wheel covers ............................. 185
Wheels and tyres .......................178