low beam OPEL CROSSLAND X 2018.5 Manual user

Vehicle care193Wiper blade replacement
Windscreen
Lift the wiper arm until it stays in the
raised position, press button to
disengage the wiper blade and
remove.
Attach the wiper blade slightly angled
to the wiper arm and push until it
engages.
Lower wiper arm carefully.
Rear window
Lift wiper arm. Disengage wiper blade as shown in illustration and remove.
Attach the wiper blade slightly angled
to the wiper arm and push until it
engages.
Lower wiper arm carefully.
Bulb replacement
Switch off the ignition and switch off
the relevant switch or close the doors.
Only hold a new bulb at the base. Do not touch the bulb glass with bare
hands.
Use only the same bulb type for
replacement.
Replace headlight bulbs from within
the engine compartment.
Bulb check
After a bulb replacement switch on
the ignition, operate and check the
lights.
Halogen headlights Halogen headlights with separate
housings for low beam and high
beam/turn light.

194Vehicle care
High beam, turn light (1)
Low beam ( 2)
High beam
1. Rotate the cap (1) anticlockwise and remove it.
2. Withdraw the upper bulb holderfrom the reflector housing.
3. Remove the bulb from the plugconnector by pulling.
4. Replace the bulb and connect it to
the plug connector.
5. Insert and push the bulb holder into the reflector housing by
setting the lug into position.
6. Fit the cap and rotate clockwise.
Turn light
1. Rotate the cap (1) anticlockwise and remove it.

Vehicle care195
2. Rotate the lower bulb holderanticlockwise to disengage.
Withdraw the bulb holder from the
reflector housing.
3. Press latch and remove the bulb from the bulb holder.
4. Replace the bulb and attach it to the bulb holder.
5. Insert the bulb holder into the reflector housing and rotate
clockwise.
6. Fit the cap and rotate clockwise.
Low beam
1. Rotate the cap (2) anticlockwise and remove it.
2.Lift the retainer, then pull the plug
connector backwards.
3. Fold down the retainer and remove the bulb from the reflectorhousing.

196Vehicle care4. Replace the bulb and push it intothe reflector housing by setting
the lug into position.
5. Fold up the retainer and hold in position.
6. Attach the plug connector to the bulb and fix it with the retainer.
7. Fit the cap and rotate clockwise.
Sidelight/Daytime running light In case of defective LEDs, have them
replaced by a workshop.
LED headlights
Headlights for low and high beam,
sidelights, daytime running lights and turn lights are designed as LEDs and
can not be changed.
Have lights repaired by a workshop in
case of failure.
Fog lights
The bulbs are accessible from the
underside of the vehicle.
1. Turn the bulb holder anti- clockwise and remove it from the
reflector housing.
2. Disengage the bulb socket from the plug connector by pressing
the retaining lug.
3. Remove and replace the bulb socket with bulb and attach the
plug connector.
4. Insert the bulb socket into the reflector housing by turning
clockwise and engage.
Tail lights
Depending on version, tail lights and
brake lights are designed as LEDs. In case of failure, have LEDs replaced
by a workshop.

256Headlights................................... 109Head restraint adjustment .............8
Head restraints ............................ 42
Head-up display............................ 98 Heated mirrors ............................. 35
Heated rear window ..................... 38
Heated steering wheel .................73
Heated windscreen .......................39
Heating ........................................ 46
Heating and ventilation system . 118
High beam ........................... 93, 110
High beam assist ..........................93
Hill start assist ........................... 148
Horn ....................................... 14, 74
I
Identification plate .....................230
Ignition switch positions .............131
Immobiliser .................................. 34
Indicators ...................................... 84
Inductive charging ........................78
Info Display ................................... 97
Instrument cluster ........................80
Instrument panel fuse box .........203
Instrument panel illumination .....201
Instrument panel illumination control .................................... 115
Instrument panel overview ........... 10
Interior care ............................... 225
Interior lighting ............................ 115Interior lights ...................... 115, 201
Interior mirrors .............................. 36
Interruption of power supply ......145
Introduction .................................... 3
J Jump starting ............................. 219
K Keys ............................................. 21
Keys, locks ................................... 21
L
Lane departure warning .......91, 174
Lashing eyes ............................... 68
LED headlights ........................... 196
Lighting features .........................116
Light switch ................................ 109
Load compartment ................30, 64
Load compartment cover .............67
Loading information .....................70
Low beam ..................................... 93
Low fuel ....................................... 93
LPG ...................................... 85, 177
M Malfunction indicator light ............90
Manual anti-dazzle ......................36
Manual mode ............................. 144
Manual transmission .................. 146Mirror adjustment ........................... 9
Misted light covers .....................114
N New vehicle running-in ..............131
Number plate light .....................201
O Object detection systems ...........160
Odometer ..................................... 84 Oil, engine .......................... 228, 232
OnStar ........................................ 105
Outside temperature ....................76
Overrun cut-off ........................... 136
P Panoramic view system ..............170
Parking ................................ 19, 138
Parking assist ............................ 160
Parking brake ............................ 148
Parking lights ............................. 114
Particulate filter ........................... 139
Performance .............................. 237
Performing work ........................188
Power button .............................. 132
Power outlets ............................... 77
Power saving mode ....................133
Power windows ............................ 37
Preheating ................................... 92
Puncture ..................................... 215