lock OPEL FRONTERA 1998 Workshop Manual

AUTOMATIC TRANSMISSION (AW30-40LE) 7A–73
Check circuitTe r m i n a l
Measuring condition Voltage (V)
+-
Winter lamp C79-12C78-15
or -19Winter lamp ON Less than 1
Winter lamp OFF 8
16
Solenoid S1 C78-4C78-15
or -19OFF (3rd or O/D) Less than 1
ON (1st or 2nd) 8
16
Solenoid S2 C78-3C78-15
or -19OFF (1st or O/D) Less than 1
ON (2nd or 3rd) 8
16
Lock up solenoid SL C78-12C78-15
or -19OFF (Lock up OFF) Less than 1
ON (Lock up ON) 8
16
Pressure control solenoid C78-11 C78-8At throttle pressure changing Less than
1
8-16
Oil temperature sensor C79-18 C79-27ATF temperature 20
C4.70
ATF temperature 80
C3.65
Tech 2 diagnosis terminal
(J1850)C78-6C78-15
or -19On diagnosis communication 0-1.5
6.25-8.0
Throttle position sensor
(ground)C79-19C78-15
or -19Key switch ON
-0.1
0.1

7A–76 AUTOMATIC TRANSMISSION (AW30-40LE)
249RY00010
249RY00008
NEUTRAL START SWITCH INSPECTION
Inspection
With a circuit tester, make a continuity test on the neutral star t
switch with the moving piece set in each position.
Continuity
Removal
Preparation:
Disconnect negative (–) battery cable.
1. Remove rear sound cover.
2. Remove the rear side ATF cooler pipe from the
transmission elbow.
3. Disconnect neutral star t switch connector.
4. Unstake the lock washer, and then remove the shaft nut.
5. Remove the neutral start switch.
Installation
To install, follow the removal steps in the reverse order, noting
the following points;
Adjustment
1) Loosen the neutral star t switch bolt and set the shift
selector to the "N" range.
2) Align the groove and neutral basic line.
3) Hold in position and tighten the bolt.Te r m i n a l
Po s i ti on143526879
P
R
N
D
2
L
Torque Nꞏm (kgꞏcm/lbꞏin)
Nut 7 (70/61)
Bolt 13 (130/113)

7A–78 AUTOMATIC TRANSMISSION (AW30-40LE)
F07RY00019
225RY00001
220RY00001
244RX00001
PATTERN SELECT SWITCH INSPECTION
Inspect that there is continuity between each terminals.
OVERDRIVE OFF SWITCH INSPECTION
Inspect that there is continuity between terminals 2 and 4.
SOLENOID INSPECTION
1. Resistance check
• Using an ohmmeter, check the resistance between each
terminals (S1/S2/SL) and body.
• Using an ohmmeter, check the resistance between
terminals (STH) and (STHG).

NOTE:
If the pressure contorl solenoid resistance is not within
specification, replace the valve body assembly.
2. Operation Check
Check the solenoid operation by blowing into an oil hole as
shown in the figure.
Solenoid S1 and S2 (Normal close type)
Solenoid S1, S2 and Lock-up
solenoid resistance11 - 15(20C)
12 - 16
(40C)
Pressure control solenoid
resistance5 - 5.6
(20C)
5.4 - 6.1
(40C)
When battery terminal is
disconnectedNo air leaks
When battery terminal is
connectedAir passes through

7A–80 AUTOMATIC TRANSMISSION (AW30-40LE)
256RY00001
256RW012
256RW013
SELECTOR LEVER
INSPECTION
1. Make sure that when the selector lever is shifted from "P" to
"L", a "clicking" can be felt at each shift position. Make sure
that the gear corresponds to that of the position plate
indicator.
2. Check to see if the shifter lever can be shifted as shown.
REMOVAL
Preparation:
Diconnect negative (–) battery cable.
1. Transfer Control Lever Knob
2. Front Console
Disconnect wiring harness connectors.
3. Selector Lever Assembly
1) Disconnect shift lock cable from the selector lever
assembly side.
2) Disconnect wiring harness connectors.
3) Disconnect shift control rod from the selector lever
assembly side.

AUTOMATIC TRANSMISSION (AW30-40LE) 7A–81
256RW014
256RW015
INSTALLATION
To install, follow the removal steps in the reverse order, noting
the following points;
Adjustment of select lever and control rod
1) Place the vehicle on a level surface.
NOTE:
If the vehicle is not on a level surface, the shift select cable
set position will vary with the movement of the engine. To
prevent possible misadjustment of the cable, the vehicle
must be placed on a level surface.
2) Install the shift control rod (1) to the transfmission select
lever (2), and then place the lever in the "N" position.
3) Set select lever in the "N" position.
4) Push select lever forward and secure it (using a rubber
band (3), etc.) so that pin comes into contact with the wall
of detent plate.
5) Install the shift control rod (1) to the selector lever arm (4).
NOTE:
Do not apply to threaded portions.
6) After adjustment, operate select lever on a trial basis to
makes sure of its smooth operation and no abnormal
indication in each position.
Adjustment of shift lock cable
1) Set ignition key in "LOCK" position and selector lever in "P"
position.
2) Adjust cable screw cap on selector lever side to provide a
gap (slack for cable) of 1–2mm between rod on steering
lock side and stopper.
Adjust cap as follows:
a. Pull screw cap (1) in arrow direction to put off slack of
inner cable.
b. With cable kept as (a), adjust gap between nut (2) and
bracket to 5mm (0.2in).
c. Lock inner cable by tur ning nut (3) while holding nut (2) in
place.
NOTE:
Clean the rod threads and do not apply oil to the threaded
portions.Nꞏm(kgꞏm / lbꞏft)
Nut torque 32 (3.3/24)
Nꞏm(kgꞏcm / lbꞏin)
Lock nut torque 3.7 (38/33)

7A–82 AUTOMATIC TRANSMISSION (AW30-40LE)
3) Make sure of proper operation of shift lock through checks
as follows:
a. Selector lever shall not be moved out of "P" position with
ingition key in "Lock" position.
b. Selector lever can be moved out of "P" position with
ignition key in "ON" position only when brake pedal is
depressed.
c. Ignition key can be turned to "LOCK" position only when
selector lever is in "P" position (key can be pulled out).
If (a) and (c) fail, readjust cable. If (b) fails, readjust
connector wiring and brake pedal switch.

AUTOMATIC TRANSMISSION (AW30-40LE) 7A–83
826RY00005
826RY00006
249RY00011
249RY00012
TRANSMISSION CONTROL MODULE
(TCM)
REMOVAL
Preparation:
Disconnect negative (–) battery cable.
1. Disconnect the TCM harness connectors.
2. Remove fixing nuts (3 pieces) and TCM from the bracket.
INSTALLATION
To install, follow the removal steps in reverse order.
SHIFT SOLENOID AND LOCK-UP
SOLENOID
REMOVAL
Preparation:
• Disconnect negative (–) battery cable.
• Remove the rear sound cover.
• Drain the fluid.
Refer to
"ATF REPLACEMENT" in this section.
1. Remove the nineteen bolts and oil pan.
2. Remove the oil strainer assembly.
3. Disconnect the solenoid wiring connectors from the shift
solenoid S1(1), S2(2) and lock-up solenoid (3).
4. Remove each retaining bolts and solenoids.
INSTALLATION
To install, follow the removal steps in reverse order noting the
following point;
Tprque Nꞏm (kgꞏcm/lbꞏin)
Solenoid S1, S2 bolt 7 (70/61)
Lock-up solenoid bolt 10 (100/87)

7A–92 AUTOMATIC TRANSMISSION (AW30-40LE)
249RW003
240RY00001
240RY00002
Important operations
3. Transmission control rod and shift lever
Remove the transmission control rod and shift lever.
4. Neutral start switch
Unstake the lock washer.
Remove the nut and bolts, and then remove the neutral star t
sw itc h.
Remove the lock washer and grommet.
5. Elbow
Remove two elbows from transmission case.
Install special tool to the transmission unit.
Holding fixture: 5-8840-2152-0 (J-37227)
Fixture base: 5-8840-0003-0 (J-3289-20)

AUTOMATIC TRANSMISSION (AW30-40LE) 7A–95
249RY00011
249RY00012
244RY00017
240RY00028
4. Solenoid wiring
Disconnect the connectors from the solenoid S1(1), S2(2),
lock-up solenoid (3) and pressure control solenoid (4).
Turn over transmission, remove the solenoid wiring stopper
plate from the case.
Pull the wiring out of the transmission case.
5. Valve body
Remove the twenty bolts from valve body.
6. Check valve, spring
7. Spring
Remove the check valve and spring.
Remove two springs from C-0 accumulator piston.

AUTOMATIC TRANSMISSION (AW30-40LE) 7A–115
252L100003
252L100004
252L100005
252L100016
Important operations
Check operation of one-way clutch
Hold the OD direct clutch drum and turn the input shaft.
The input shaft should turn freely clockwise and should lock
counterclockwise.
(1): Free
(2): Lock
1. OD direct clutch assembly
Remove OD direct clutch assembly from OD planetary
gear.
2. Thrust bearing
Then remove thrust bearing with the race from OD direct
clutch drum.
Check piston stroke of OD direct clutch (C-O)
Place the oil pump onto the torque conver ter, and then
place the OD direct clutch assembly onto the oil pump.
Use a dial indicator, measure the OD direct clutch piston
stroke applying and releasing the compressed air (4– 8 kg/
cm
2, 57– 114 psi, 392– 785 kPa) as shown.
mm (in.)
Piston stroke1.85– 2.15
(0.0728– 0.0847)