lights OPEL MERIVA 2009 User Guide

88 Instruments, Controls
Picture no: 17906s.tif
Coolant temperature display
Coolant temperature display For physical reasons, the engine
temperature gauge shows the coolant
temperature only if the coolant level is
adequate.
During operation the system is pressurised.
The temperature may therefore rise briefly
to over 100 C.
Picture no: 17907s.tif
Fuel gauge
Fuel tank level display.
If the fuel level is too low, a warning lamp
lights up
Y. When the light flashes, refuel as
soon as possible.
Never run the tank dry!
Because of the fuel remaining in the tank,
the amount of fuel required to fill the
tank may be less than the specified tank
capacity.
Pointer in zone at
left
= Engine operating
temperature not yet
reached.
Pointer between
the zones = Normal operating
temperature.
Pointer in zone at
right (warning
zone) = Temperature too
high: Stop vehicle
and switch off
engine. Danger to
engine. Check
coolant level
immediately 3 213.

101
Instruments, Controls
Picture no: 14056h.tif
Windscreen washer and headlamp
washer system 3
Pull stalk towards steer ing wheel. Screen
wash is squirted onto the screen and the
wipers move back and forth a few times.
When the lights are switched on,
windscreen wash is al so squirted onto the
headlamps.
Picture no: 14057h.tif
Rear window washer and wiper system
Push stalk forwards. The rear window wiper
wipes in timed interval mode. Switch off by
pulling stalk towards the steering wheel.
If the stalk is held forwards, washer fluid is
sprayed on the rear window.

102 LightingLighting
Picture no: 14756s.tif
Exterior lightsTurn light switch:
In positions 8 and 9, the tail lamps and
number plate lamps are also on.
If the ignition is switched off when main
beam or dipped beam is on, the parking
lamps come on. Model with daytime running lights
3
With ignition on and lights turned on 7, the
dipped headlamps are on without
instrument illumination.
The daytime running lig hts switch off when
the ignition is switched off.
Follow the regulations of the country in
which you are driving when using daytime
running lights and fog lamps 3.
Driving abroad 3110.
Exterior lights ....................................... 102
Main beam, headlamp flash .............. 103
Turn signal lamps ................................ 103
Fog lamps > 3
.................................... 103
Fog tail lamp r................................... 104
Reversing lamps................................... 104
Hazard warning lamps ....................... 104
Headlamp range adjustment ?......... 104
Adaptive Forward Lighting 3 (AFL) .. 106
Lead-me lighting 3............................. 107
Instrument illumination k,
Information display illumination ...... 108
Courtesy lamp...................................... 108
Battery discharge protection 3.......... 110
Misted light covers............................... 110
Headlamps when driving abroad ...... 110 7
=Off
8 = Parking lamps
9 = Dipped or main beam

103
Lighting
Picture no: 18475s.tif
Main beam, headlamp flash Push stalk forward to switch from dipped
beam to main beam.
To switch to dipped beam, press stalk
forwards again.
To operate the headlamp flash, pull stalk
towards steering wheel. The main beam is
switched on for as long as the stalk is held
in this position.
Picture no: 14054h.tif
Turn signal lamps If the stalk is moved past the resistance
point, the turn signal lamp remains on.
When the steering wheel moves back
toward the straight-ahead position, the
turn signal lamp is automatically
deactivated.
Brief flash: press stalk to perceptible
resistance and release.
Manual disconnection of turn signal lamps
by returning to centre position.
Picture no: 14758s.tif
Fog lamps
> 3

The fog lamps can only be switched on
when both the ignition and lights are on.
Operated with the > button.
Lever upwards = Right turn signal
Lever downwards = Left turn signal

106 Lighting
Picture no: 15209j.tif
Adaptive Forward Lighting
3
(AFL) ensures better illumination of
zbends (curve lighting),
z crossings and narrow bends (cornering
light).
Curve lighting
The light beam pivots based on
steering wheel position and speed (from
approx. 10 km/h).
The headlamps shine at an angle of up
to 15 to the right or left of the direction of
travel.
Picture no:
Cornering light
An additional lamp comes on with
certain steering wheel positions (after
approx. 90), turn si gnal settings and
speeds (up to approx. 40 km/h).
The light is thrown approx. 90 to the
left or right of the car, to a distance of
approx. 30 metres.
Reversing function
If the lights are on, reverse gear is
engaged, and the turn signal is activated,
the cornering light on the appropriate side
is switched on. The cornering light stays on
for 15 seconds once the turn signal has
been switched off.
Picture no: 17887s.tif
Control indicator B for adaptive driving
lights
Illuminated: Fault in system. The system is
not ready for operation.
Contact a workshop for assistance.
After a power supply interruption the
steering angle sensor must be calibrated to
make the system operational. 3147
Control indicator
B flashes for
about 4 seconds after the ignition is
switched on as a reminder that the
headlamps have been converted, see
"Headlamps for driving abroad" 3110.

108 LightingTo activate the lead-me-to-the-car light
function, press button q on the remote
control twice with the vehicle locked.
Country-specific version 3: to enable the
lead-me-to-the-car function, press
button q on the remote control once with
the vehicle locked.
The lead-me-to-the-car light function is
deactivated immediately by pressing
button p of the remote control or
switching on the ignition.
Picture no: 14759s.tif
Instrument illumination
k,
Information display illumination
Lights come on when ignition is switched on.
Brightness can be adjusted when the
exterior lights are on: Push to release knob
k and then turn it clockwise or
anticlockwise and hold until the desired
brightness is obtained.
Display mode 3 396.
Picture no: 14136s.tif
Courtesy lamp Automatic interior light
Comes on automatically when the vehicle is
unlocked with the radi o remote control or
when a door is opened.
Goes off automatically after a delay when
the doors are closed or immediately when
the ignition is switched on or the doors are
locked.
Front courtesy lamp
To operate manually from inside when the
doors are closed: on = Press light switch 0
off = Press light switch 0 again

110 LightingBattery discharge protection
3
Some consumers such as the interior
lighting switch themselves off after
approx. 30 minutes if the ignition is off in
order to protect the battery charge. Misted light covers The inside of the light covers may mist up
briefly in poor, wet and cold weather
conditions, in heavy rain or after washing.
The mist disappears quickly by itself; to
help, switch on the lights. Headlamps when driving abroad The asymmetrical dipped beam increases
the field of vision on the passenger side of
the lane.
In countries where traffic drives on the
opposite side of the road, prevent glare as
follows.
Vehicles with halogen headlamp system
or Xenon headlamp system 3
Have headlights conver ted in a workshop.
Picture no: 14053h.tif
Vehicles with Adaptive headlight 3 (AFL)
1. Pull stalk towards steering wheel and hold.
2. Switch on ignition.
3. After approx. 3 seconds, an acoustic signal sounds and then AFL control
indicator
B flashes approx. 4 seconds.
After the switch, AFL control indicator
B
flashes for 4 seconds each time the ignition
is switched on. To return to asymmetrical dipped beam,
pull and hold the main beam stalk again,
switch on the ignition and wait for the
acoustic signal. AFL control indicator
B
will then discontinue flashing.
Control indicator
B
3 106.

130 Driving and operation
Picture no: 18386s.tif
Starting the engine
When starting the engine, activate the
footbrake at the same time. The engine
can only be started in position N and with
the footbrake activated. The transmission
display shows "N". If the footbrake is not
activated, the control light j 3 in the
instrument panel illuminates and "N"
flashes in the transmission display, the
engine cannot be started.
If no brake lights are operational, the
engine will not start.
Picture no: 14175s.tif
Operation of manual transmission
automated using selector lever
Always move the selector lever all the way
to the stop. Note the gear or mode
indicator in the transmission display.
Move selector lever toward N
Neutral. Selector lever in
o (centre position)
Once the selector lever has been moved
from N to position o (centre position) with
the foot brake operated, the Easytronic is
in automatic mode and first gear has been
selected (second gear with winter
programme enabled). "A" appears in the
transmission display.
When the foot brake is released the vehicle
starts to "creep". If the foot brake is not
operated, "A" flashes. Start off by pressing
the accelerator immediately or more
selector lever back to N and repeat
procedure with foot brake operated.
In Automatic mode, selection of other
gears is automatic irrespective of driving
conditions.

133
Driving and operation
Picture no: 14083j.tif
Manoeuvring the vehicle
For accurate manoeuvring when parking,
at garage entrances etc., the creeping
movement can be utilised by releasing the
foot brake with a gear selected.
Never actuate accelerator and brake
pedals simultaneously.
To prevent damage, the manual
transmission automated deactivates the
"creep function" when the temperature of
the automatic clutch is extremely high. Vehicle storage
Apply the handbrake and remove the key
from the ignition. The most recently
engaged gear (indicator in transmission
display) remains engaged. With
N, no gear
is engaged.
When the ignition is switched off the
manual transmission automated no longer
responds to movement of the selector
lever.
If the ignition key is not removed, the
battery may be discharg ed if the vehicle is
then left to stand for a lengthy period of
time.
If the hand brake has not been applied, the
control indicator R flashes for a few
seconds after the ignition is switched off.
Picture no: 17890s.tif
Fault
To prevent damage to the automated
manual transmission, the clutch is closed
automatically at high clutch temperatures.
Warning light A lights up if there is a fault.
It is possible to continue driving but manual
mode can no longer be used for changing
gear.
If "F" also appears in the transmission
display, it is not possible to continue
driving.
Have cause of fault remedied by a
workshop. The system’s integrated self
diagnostics allow faults to be quickly
remedied.

137
Driving and operation
Saving fuel, protecting the
environmentTrend-setting technology
Environmentally friendly and mainly
recyclable materials were used when your
vehicle was being developed and
manufactured. The production methods
used to make your vehicle are also
environmentally-compatible.
Recycling of production wastes keeps the
circulation of material closed. Reduction of
energy and water requirements also helps
to conserve natural resources.
A highly advanced design means that your
vehicle can be easily disassembled at the
end of its working life, and the individual
materials separated for subsequent re-use.
Materials such as asbestos and cadmium
are not used. The refrigerant in the air
conditioning system 3 is CFC-free.
New painting techniques employ water as
a solvent. End-of-life vehicle recovery
Information on end-of-life vehicle recovery
centres and the recycling of end-of-life
vehicles is availabl
e at www.opel.com.
Energy and environment-conscious
driving
z High noise levels and exhaust emissions
are often a result of driving without due
attention to saving energy and
protecting the environment.
z You should therefore drive with energy in
mind: "more miles – less fuel".
Reduce the noise level and exhaust
emissions by adopting an environment-
conscious driving style. This is extremely
worthwhile and improves the quality of
life.
Fuel consumption depends to a great
extent on your own personal driving
style. The following hints are intended to
help you consume fuel at a rate that is as
close as possible to the specified levels
3224.
Check your vehicle’s fuel consumption
every time you refuel. This facilitates
early detection of any irregularities
causing increased fuel consumption. Warming up
z
Full throttle and warming up at idle
speed increase wear, fuel consumption,
exhaust emission, the amount of
pollutant in the exhaust and the amount
of noise.
z Drive off immediately after starting.
Warm up the engine by running it at
moderate engine speeds.
Uniform speed
z Hectic driving significantly increases fuel
consumption, the exhaust emissions, the
proportion of pollutant in the exhaust
gas and the noise level.
z Do not accelerate and brake
unnecessarily. Drive at uniform speed,
watching the road.
Avoid frequent starting off and stopping
e.g. at traffic lights, in short distance
traffic and in queues of traffic by means
of clever planning. Select roads with
good traffic flow.
Idling
z The engine also consumes fuel when
idling.
z If you have to wait for more than one
minute, it is worthwhile switching off the
engine. Five minutes of idling
corresponds to approximately one
kilometre of driving.