height OPEL MERIVA 2009 Owners Manual

3
In Brief
Picture no: 13978s.tif
To adjust front seat backrests:
Turn handwheel Do not lean on seat backrest whilst
adjusting it.
Seats 344, Seat position 345.
Picture no: 13979s.tif
To adjust front seat height
3: Pull
lever
Lift lever and relieve some weight from seat
to raise it or press down on seat with body
weight to lower it.
Seats 344, Seat position 345.
Picture no: 13980s.tif
Head restraint height of front and
rear outer seats: Tip head
restraint forward to release, hold
and adjust height, engage Head restraints 346, Centre rear head
restraint 347, Head restraint position 347,
Head restraint removal 348.

5
In Brief
Picture no: 16099s.tif
Adjust exterior mirrors
electrically
3
Select the mirror to be adjusted using the
rocker switch and adjust using the four-
way switch.
Mirror 336, Aspherical exterior mirrors 3
3 37, Swinging in exterior mirror 337,
Heated exterior mirrors 3 3 13, 341.
Picture no: 13981s.tif
Steering wheel adjustment
3:
Swivel lever down, adjust height,
swivel lever up, engage
Adjust steering wheel only when vehicle is
stationary and steering wheel lock is
released.
Airbag system 3 67, Steering wheel lock
3 15.

45
Seats, Interior
Picture no: 13979s.tif
Adjusting the seat height3
Lift front side lever and relieve some weight
from seat to raise it or press down on seat
with body weight to lower it.
Picture no: 16098s.tif
Adjusting the lumbar support 3
Turn side hand wheel on backrest while
relieving the load on the backrest.
Picture no: 18530s.tif
Seat position
z Sit with your buttocks as far back against
the backrest as possible. Adjust the
distance between your feet and the
pedals so that your legs are slightly
angled when pressing the pedals. Slide
the passenger seat as far back as
possible.
9 Warning
Only drive with the seat correctly
adjusted.

46 Seats, InteriorzSit with your shoulders as far back
against the backrest as possible. Set the
backrest rake so that you can easily
reach the steering wheel with your arms
slightly bent. Mainta in contact between
your shoulders and the backrest when
turning the steering wheel. Do not angle
the backrest too far back. We
recommend a maximum rake of
approx. 25.
z Adjust the steering wheel 35.
z Set seat height 3 high enough to have a
clear field of vision on all sides and of all
display instruments. There should be at
least six inches of clearance between
your head and the headlining. Your
thighs should rest lightly on the seat
without pressing into it.
z Adjust the head restraint.
z Adjust the height of the seat belt 362.
z Adjust the lumbar support 3 so that it
supports the natural shape of the spine.
Picture no: 14153s.tif
Heated front seats 3
Two buttons between the centre air vents
for the left and right seats.
To heat with the ignition switched on, press
button ß.
Picture no: 13980s.tif
Head restraints Adjusting the front head restraints and
the rear outboard head restraints 3
Tip head restraint forw ard, hold and adjust
height.
To fold over the rear seats or lower the
front passenger seat head restraint all the
way down and remove, see next page.
With the seats occupi ed, adjust height
according to body size.

62 Seats, Interior
Picture no: 14120s.tif
Using the belts Fitting seat belts
The seat belt must not be twisted and must
lie snugly against the body. The backrest
must not be tilted back too far (maximum
approx. 25).
Adjust the height so that the belt lies across
the shoulder. It must not lie across the
throat or upper arm.
Pull the belt out of the reel, guide it across
the body (making certain it is not twisted)
and engage the latch plate in the buckle.
Tension the lap belt frequently whilst
driving by tugging the shoulder belt.
Picture no: 14121s.tif
Loose or bulky clothing prevents the belt
from fitting snugly. Do not place objects
such as handbags or mobile phones
between the belt and your body.
9 Warning
On pregnant women in particular, the
lap belt must be positioned as low as
possible across the pelvis so as not to
put too much pressure on the abdomen.
9 Warning
The belt must not rest against hard or
fragile objects in the pockets of your
clothing.

63
Seats, Interior
Picture no: 14122s.tif
Height adjustment
Adjusting the height of the upper
deflection point of the front seat belts:
1. Unreel seat belt a little.
2. Push button on sliding adjuster.
3. Set desired height.
4. Allow sliding adjuster to audibly latch.
Do not adjust height while driving.
Picture no: 14123s.tif
Removing the belt
To release seat belt, press red button on
belt buckle.
Picture no: 14124S.tif
Three-point seat belt on centre rear seat
Pull latch plates out of belt retainer in roof.
Click bottom latch plate into right-hand
buckle ( 1) at middle seat. Remove top latch
plate from retainer, guide over shoulder
and lap area with belt (do not twist) and
click into left buckle ( 2) at middle seat.
If using the centre seat, both outboard
seats must be pushed backward and the
backrests must be flush with the centre
seat backrest 352.

66 Seats, Interior
Note
zChildren under 12 years or under 150 cm
tall should only travel in an appropriate
child restraint system.
z When transporting children, use the child
restraint systems suitable for the child’s
weight.
z Ensure correct installation of child
restraint system, see the instructions
enclosed with the system.
z The covers of the Opel child restraint
system can be wiped clean.
z Do not stick anything on the child
restraint systems and do not cover them
with any other materials.
z Only allow children to enter and exit at
the side facing away from the traffic.
z A child restraint system which has been
subjected to stress in an accident must
be replaced.
z Secure or remove child restraint systems
that are in the vehicle but not in use.
B
1= Conditional, without front
passenger airbags or with seat
occupancy recognition and Opel
child restraint systems with
transponders.
The front passenger seat must also
have a height adjusting facility:
move to highest position, slide front
passenger seat all the way back and
move front passenger seat belt
anchorage point to lowest possible
position.
B2= Conditional, without side airbag, of front passenger seat has been slid
all the way back, or with seat
occupancy recognition and Opel
child restraint systems with
transponders.
The front passenger seat must also
have a height adjusting facility:
move to highest position and slide
front passenger seat all the way
back so that the seat belt runs
towards the front from the
anchorage point.
U = Universal suitability in conjunction with three-point seat belt. + = Vehicle seat available with ISOFIX
fixings. When using ISOFIX, only
ISOFIX child restraint systems
approved for the vehicle may be
used.
++ = Only if both outboard seats are pushed back and flush with the
centre seat.
X = No child restraint system permitted in this weight class.

156 Driving and operation
Picture no: 6456u.tif
If wear in the front is greater than that in
the rear, move the rear wheels to the front
axle and vice versa.
Correct tyre pressure. General information
z
The risk of aquaplaning is greater if the
tyres are worn.
z Tyres age, even if they are not used or
used infrequently. We recommend tyre
replacement every six years at the latest.
z Never fit used tyres the previous history
and use of which you do not know. Tyre designations
Meanings:
e.g.
175/70 R 14 88 T
Speed code letters:
175 = Tyre width in mm
70 = Cross-section ratio (tyre height to
tyre width in %)
R = Belt type Radial
14 = Rim diameter in inches
88 = Load index e.g. 88 corresponds
to 567 kg
T = Speed code letter:
Q = Up to 160 km/h
S = Up to 180 km/h
T = Up to 190 km/h
H = Up to 210 km/h
V = Up to 240 km/h
W = Up to 270 km/h

163
Driving and operation
Coupling socket load
The coupling socket load is the load
exerted by the trailer/caravan on the
coupling ball. It can be varied by changing
the weight distribution when loading the
trailer/caravan.
The maximum permissible coupling socket
load (55 kg) of the towing vehicle is
specified on the towing equipment
identification plate and in the vehicle
documents. This must always be complied
with, particularly in the case of heavy
caravans/trailers. The coupling socket load
should be no less than 25 kg.
When measuring the coupling socket load,
make sure that the drawbar of the loaded
trailer/caravan is at the same height as it
will be when the trailer/caravan is coupled
with the towing vehicle loaded. Particularly
important for trailers/caravans with
tandem axle. Rear axle load during towing
With the trailer connected and the towing
vehicle fully loaded including all
occupants, the permitted rear axle load
(specified on the identification plate and
vehicle documents) must be exceeded by
no more than 25 kg and the maximum
permitted gross vehicle weight by no more
than 30 kg. If the maximum permitted rear
axle load is exceeded, a maximum speed
of 100 km/h applies, and 80 km/h for
commercial vehicles.
Driving characteristics, towing tips
Before attaching th
e trailer/caravan,
lubricate the ball of the trailer/caravan
towing device. However, do not lubricate
the ball if a stabiliser, which acts on the
coupling ball, is being used to damp
hunting.
Check caravan/traile r lighting before
starting to drive. The fog tail lamps on the
vehicle are deactivated when towing a
caravan or trailer.
Trailers with LED turn signals must have a
provision enables lamp monitoring for
commercial bulbs.
Handling is greatly influenced by the
loading of the trailer/caravan. Loads
should therefore be secured so that they
cannot slip and be placed in the centre of
the trailer/caravan if possible, i.e. above
the axle.
In the case of trailers with low driving
stability, do not exceed a speed of 80 km/h;
the use of a friction-type stabiliser is
strongly recommended.

176 Self-help, vehicle care
Picture no: 11643s.tif
2. Push the wheel bolt wrench 3 on as far
as possible and slacken the wheel bolts
half a turn.
Picture no: 14724s.tif
3. The jacking points are marked.
On Meriva OPC and OPC Line and
vehicles with sill trims, the jack 3 cannot
be used. It could damage the vehicle.
Picture no: 14762s.tif
4. Set the jack 3 to the required height by
turning the lug by hand. Fit the jack arm
at the front – or rear – so that the jack
claw (arrow in Fig.) grasps the vertical
ridge and engages in the recess in the
ridge. Ensure that the claw is properly
positioned.