reset OPEL MERIVA 2009 Owners Manual

87
Instruments, Controls
Picture no: 12097s.tif
y

Seat occupancy recognition 3
3 67, 372.
Picture no: 17879s.tif
Instrument display In some versions, the indicators of the
instruments briefly rotate to the end
position when the ignition is switched on.
Tachometer
Displays the engine rpm.
Drive in a low engine speed range for each
gear as much as possible.
Speedometer
Speed display. Picture no:
Kilometre display
If the ignition is off the mileage is displayed
for approx. 15 seconds by briefly pressing
the reset knob.
Top line:
Trip odometerDisplays the number of
kilometres since the
gauge was reset.
To reset, hold the reset knob depressed for
a few seconds with the ignition on.
Bottom line:
OdometerRecords the number of kilometres.
Maintenance, Inspection system, 389,
3 208.
Caution
If the pointer is in the warning zone, the
maximum permitted engine speed is
exceeded. Engine at risk.

98 Instruments, ControlsDistance travelled
Display of distance travelled. The
measurement can be reset at any time.
Average speed
Display of average speed. The
measurement can be reset at any time.
Stoppages in the journey with the ignition
off are not included in the calculations.
Effective consumption
Display of fuel consumed. The
measurement can be reset at any time.
Average consumption
Display of average consumption. The
measurement can be reset at any time.
Picture no: 16719t.tif
Restart trip computer
The measurement or calculation of the
following trip computer information can be
restarted:
zDistance,
z Average speed,
z Effective consumption,
z Average consumption.
Select BC 1 or BC 2 from the trip computer
menu.
Picture no: 16720t.tif
The information of the two trip computers
can be reset separately, making it possible
to evaluate data from different time
periods.
Select the required trip computer
information and confirm.
The value for the selected function will be
reset and recalculated.
Ü
Board Computer 19,5° 19:36
BC 1 All values
BC 2
257.0
km
Timer
Ø40
km/h
31.0
Ltr.
Ø
7.0
Ltr./100km
1
8
Ü
Reset BC 1 19,5° 19:36
All values
257.0
km
Ø40
km/h
31.0
Ltr.
Ø
7.0
Ltr./100km

99
Instruments, Controls
Picture no: 16721t.tif
To reset all information of a trip computer,
select menu item All values.
After resetting, - - - is displayed for the
selected trip comput er information. The
recalculated values are displayed after a
brief delay.
Interruption of power supply
If the power supply has been interrupted or
if the battery voltage has dropped too low,
the values stored in the trip computer will
be lost.
Picture no: 16722t.tif
Stop watch
Select menu item Timer from the Board
Computer menu.
The Timer menu is displayed.
To start, select menu item Start. To stop,
select menu item Stop.
To reset, select menu item Reset. The desired stop watch display can be
selected from the Options
menu 3:
Driving Time excl. Stops
The time the vehicle is in motion is
recorded. Stationary ti me is not included.
Driving Time incl. Stops
The time the vehicle is in motion is
recorded. The time the vehicle is stationary
with the key in the ignition switch is
included.
Travel Time
Measurement of the time from manual
activation via Start to manual deactivation
via Reset .
Ü
Reset BC 1 19,5° 19:36
All values
257.0
km
Ø40
km/h
31.0
Ltr.
Ø
7.0
Ltr./100km
Ü
Board Computer 19,5° 19:36
BC 1
BC 2
00:00:00
Timer Start
Reset
Options

123
Climate control
Picture no: 16496s.tif
Automatic mode
Basic setting for maximum comfort:
zPress AUTO button.
z Open all air vents.
z Switch on AC compressor 3125.
z Preset temperature to 22 C with turn
knob.
The temperature can be set higher or lower
as desired. Switching off the air conditioning
compressor (
ECO appears in display) can
have a detrimental effect on comfort and
safety 3125.
All air vents are actuated automatically in
automatic mode. The air vents should
therefore always be open 3115. Temperature preset
The left rotary knob can be used to set the
temperature to values of between 16 C
and 28 C.
For the sake of comfort, only change the
pre-selected temperature in small steps.
If the temperature setting is less
than 16 C,
LO appears in the air
conditioning display: the climate control
system runs constantly at maximum
cooling power, and the temperature is not
regulated.
If the temperature setting is
above 28 C, HI appears in the air
conditioning display: the climate control
system runs constantly at maximum
heating power, and the temperature is not
regulated.
The temperature settings remain stored
when the ignition is turned off.

202 Service and maintenance⊕additional work.
o The intervals are shorter where driving conditions are more arduous or country-specific.
Service work
after year
1)
km (x1000)
1)
1)Depending on what occurs first.
1
30 2
60 3
90 4
120 5
150
⊕o
Remove brake drum, clean, carry out visual check every 4 years/60 000 km
Visually inspect steering system boots, track rods, final drive xxxxx
Check track rod end and supporting ball joint xxxxx
⊕
Change brake and clutch fluids (manual transmission automated) every 2 years
Loosen wheel mountings and tighten to 110 Nm
xx
Grease or apply oil to
bolt taper when fitting.
Check tyre condition and pressure (inclu ding spare wheel), correct if necessary.
If there is a tyre inflation system, check that the set is complete and the use-by date is
still valid. Replace sealant bottle every four years.
⊕
Annual service check if the annual distance travelled is greater than 20 000 km.
Visually check the first aid kit (that it is wher e it should be, that it is undamaged and that
the use by date is still valid), lashing eyes and warning triangle every 2 years
Check headlamp settings (including auxi liary headlamps), adjust if necessary xx
Lubricate door hinges, check arms, cylinder lo ck, door latch, bonnet catch, rear panel
hinge xx
Test run, final check (check steering and ig nition lock, instrument and warning lamps,
entire brake system, steering, air conditioni ng system, engine, bodywork and chassis,
reset service/interval display with TECH 2. xxxxx
⊕
Germany only: carry out emissions check, main inspection
First time after three years, then every 2 years
If used commercially to tran sport passengers, taxis, ambulances, hire cars etc annually

205
Service and maintenance
⊕ additional work.
o The intervals are shorter where driving conditions are more arduous or country-specific.
Service work
after year
1)
km (x 1000)
1)
1)Depending on what occurs first.
1
15 2
30 3
45 4
60 5
75
⊕o
Remove brake drum, clean, carry out visual check every 4 years/60 000 km
Visually inspect steering system boots, track rods, final drive xxxxx
Check track rod end and supporting ball joint xxxxx
⊕
Change brake and clutch fluids (manual transmission automated) every 2 years
Loosen wheel mountings and tighten to 110 Nm
xx
Grease or apply oil to
bolt taper when fitting.
Check tyre condition and pressure (inclu ding spare wheel), correct if necessary.
If there is a tyre inflation system, check that the set is complete and the use-by date is
still valid. Replace sealant bottle every four years.
⊕
Annual service check if the annual distance travelled is greater than 20 000 km.
Visually check the first aid kit (that it is wher e it should be, that it is undamaged and that
the use by date is still valid), lashing eyes and warning triangle every 2 years
Check headlamp settings (including auxi liary headlamps), adjust if necessary xx
Lubricate door hinges, check arms, cylinder lo ck, door latch, bonnet catch, rear panel
hinge xx
Test run, final check (check steering and ig nition lock, instrument and warning lamps,
entire brake system, steering, air conditioni ng system, engine, bodywork and chassis,
reset service/interval display with TECH 2. xxxxx

208 Service and maintenance
Picture no: 18602s.tif
Inspection system In order to guarantee economical and safe
vehicle operation and to maintain the
value of your vehicle, it is of vital
importance that all maintenance work is
carried out at the proper intervals.
Fixed service interval
When service is due, InSP appears in the
odometer display for
approximately 10 seconds when the
ignition is switched on. Have the next
service performed by a workshop within
one week or 500 km (whichever occurs
first). The service interval display takes account
of off-the-road periods during which the
battery is disconnected.
Flexible service interval
3
The length of the service intervals is based
on several parameters stemming from
usage. For this reason, various
engine-specific data is continually
gathered and is used to calculate the
remaining distance until the next service.
If the remaining distance is less
than 1500 km, InSP is displayed with a
remaining distance of 1000 km when the
ignition is switched on and off. If less
than 1000 km remains, InSP is displayed for
several seconds. Have the next service
performed by a workshop within one week
or 500 km (whichever occurs first).
Display of remaining distance:
1. Switch off ignition.
2. Briefly press the trip odometer reset button. The odometer reading is shown.
3. Press and hold the reset button for about 2 seconds. InSP and the remaining
distance are displayed. Further information
on maintenance and
the inspection system can be found in the
Service and Warranty Booklet, which is in
the glove compartment.
Have maintenance work – and repair work
on the body and the equipment – carried
out professionally by a workshop. We
recommend using your Opel partner, who
has excellent knowledge of Opel vehicles
and has the necessary special tools and
up-to-date service inst ructions from Opel.
It is particularly advisable to use an Opel
Partner during the warranty period in order
to prevent loss of warranty. Further
information can be found in the Service
and Warranty Booklet.
Separate anti-corrosion service
Have this work done at the intervals given
in the Service and Warranty Booklet.