remove seats OPEL VIVARO C 2020.25 Manual user

Seats, restraints47Seats, restraintsHead restraints............................ 47
Front seats ................................... 48
Seat position .............................. 48
Manual seat adjustment ............48
Power seat adjustment ..............50
Seat folding ............................... 51
Armrest ...................................... 52
Heating ...................................... 52
Massage .................................... 53
Rear seats ................................... 53
Seat belts ..................................... 57
Three-point seat belt .................58
Airbag system .............................. 61
Front airbag system ...................64
Side airbag system ....................64
Curtain airbag system ...............65
Airbag deactivation ....................65
Child restraints ............................. 67
Child restraint systems ..............67
Child restraint installation locations ................................... 70Head restraints
Position9 Warning
Only drive with the head restraint
set to the proper position.
The upper edge of the head restraint
should be at upper head level. If this
is not possible for extremely tall
people, set to highest position, and
set to lowest position for small people.
Adjustment
Height adjustment
Move the head restraint upwards or
downwards. If the head restraint is engaged press the catch and move
the head restraint.
Removal
Move the head restraint upwards and remove it. If the head restraint is
engaged press the catch and move
the head restraint.
Installation
Engage the head restraint rods in the
openings and push it downwards.

Seats, restraints51Backrest inclination
Tilt the switch forwards / backwards.
Lumbar support
Press J to suit personal
requirements.
Seat folding Depending on version, the front seatscan be folded flat to the table position.
Front seats backrest
Folding
Slide the front seat as far back as
possible, to avoid contact with the
instrument panel during folding.
Push the head restraint down or
remove it before folding backrest.
Head restraints 3 47.
If available fold up the armrest.
Armrest 3 52.
Pull the lever, fold the backrest fully
forwards and release the lever.
9 Warning
When the front passenger seat is
in the folded position, the front
passenger airbag system must be deactivated.
Airbag deactivation 3 65.
Unfolding
To restore the seat to the upright
position, pull the lever and raise
backrest fully. Then release the lever.

Seats, restraints53Activate seat heating by turning the
thumb wheel " for the respective
front seat. There are three intensity
levels of heating.
To deactivate the seat heating turn
the thumb wheel " to 0.
Prolonged use of the highest setting
for people with sensitive skin is not
recommended.
Seat heating is operational when engine is running and during an
Autostop.
Stop-start system 3 157.
MassageActivate the back massage function
by pressing K. The LED in the button
illuminates to indicate activation.
The massage function is activated for
a period of 1 hour. During this time,
massage is performed in six cycles
with breaks in between.
To adjust the intensity of the massage press L. Two levels of massage are
available.
Pressing K once more deactivates
massage function. The LED goes off.
The massage function is operational
when engine is running and during an Autostop.
Stop-start system 3 157.Rear seats9 Warning
When seats are being adjusted or
folded, keep hands and feet away
from the moving area. Risk of
injury.
Ensure that there are no objects
on the anchor points or rails.
Never adjust seats while driving as they could move uncontrollably.
Drive only with engaged seats and
backrests.
Depending on version the levers of
the seats can be located at different
places. The illustrations show
examples.
Seat backrest
Folding backrest down to table
position
1. Push the head restraint down or remove it before folding the
backrest.
Head restraints 3 47.

54Seats, restraints2. If available fold up the armrest.Armrest 3 52.
3. Pull the front lever or push the rear
lever to release the backrest.
4. Fold the backrest fully down.
Unfolding the backrest 1. Pull the front lever or press the rear lever.
2. Raise the backrest fully upwards until it engages.
Fixed rear seats
Easy entry function
To permit an easy entrance to the
seats of the third row, the seats of the second row can be tilted.
Pull the release lever and tilt seat to
the front.
To restore the original position tilt seat back until it is engaged.
Tilted position 1. Fold the backrest down to the table position.
2. Pull the release lever and tilt theseat to the front.
Removing
Depending on version seats can be
removed.
1. Fold the backrest down to the table position.
2. Move the seat to the tilted position.

Seats, restraints55
3. Release each front mount bypulling the respective lever.
4. Remove the seat.
Installing
1. Engage front mounts in the anchorages.
2. Push the levers to lock the frontmounts and tilt the seat back until
it is engaged.
3. Unfold the backrest.
Rear seats on rails The single seats as well as the seat
bench seat can be moved individually forwards and backwards. The
backrest of the seat bench is splitted.
Backrest inclination
Pull the front lever or push the rear
lever to release and adjust the
backrest.
Release the lever when the desired
position is obtained.

56Seats, restraintsLongitudinal adjustment
To release the seat, pull the front
handle upward or pull the loop on the rear without going beyond the point ofresistance.
Slide the seat forwards or backwards.
Longitudinal adjustment of row with
seat bench
To move the seat bench or the single
seat along the full length of the rail,
fold down the backrest to the table
position.
Release and move the seat by pulling the loop on the rear without going
beyond the point of resistance.
The arrow has to be positioned within
the marking.
Raise the backrest fully upwards.
Removing 1. Fold the backrest down to the table position.2. Pull the loop on the rear beyondthe point of resistance and tilt the
seat to the front.
3. Remove the seat.
Caution
Do not use the loop to lift the seat.
Installing 1. The loop on the rear has to be in the release position.

Seats, restraints69The following child restraints arerecommended for the following
weight classes:
● Group 0+ :
Römer Baby-Safe Plus installed
in the rearward facing position
with or without ISOFIX base for
children up to 13 kg
● Group I :
RÖMER Duo Plus ISOFIX with or without ISOFIX and Top-tether
for children from 9 kg to 18 kg
● Group II, Group III :
Römer Kidfix XP with or without
ISOFIX for children from 15 kg to
36 kg
The child is restrained by the seat belt.
The installation is permitted only
on the outer rear seats. The head restraint has to be removed.
● Group II, Group III :
Graco Booster for children from
15 kg to 36 kg
The child is restrained by the seat belt.The installation is permitted on
the front passenger seat or the
rear seats.
Ensure that the child restraint system to be installed is compatible with the
vehicle type.
Ensure that the mounting location of
the child restraint system within the
vehicle is correct, see following
tables.
Allow children to enter and exit the
vehicle only on the side facing away
from the traffic.
When the child restraint system is not in use, secure the seat with a seat beltor remove it from the vehicle.
Note
Do not affix anything on the child
restraint systems and do not cover
them with any other materials.
A child restraint system which has
been subjected to stress in an
accident must be replaced.

72Seats, restraints2:adjust seat backrest inclination as far as necessary to a vertical position to ensure that the belt is tight on the buckle
side3:move the respective seat ahead of the child restraint system forwards as far as necessary and adjust its backrest
inclination as far as necessary to a vertical position4:adjust the respective headrest as necessary or remove if required5:single seats: with a child seat installed on the centre seat, usage of outer seats is not allowed6:fixed seat bench; folding seat bench is in process of being approved

Seats, restraints774:adjust the respective headrest as necessary or remove if required5:with a child seat installed on the centre seat, usage of outer seats is not allowed6:fixed seat bench; folding seat bench is in process of being approved
ISOFIX size class and seat device
A – ISO/F3:forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kgB – ISO/F2:forward-facing child restraint system for smaller children in the weight class 9 to 18 kgB1 – ISO/F2X:forward-facing child restraint system for smaller children in the weight class 9 to 18 kgC – ISO/R3:rear-facing child restraint system for children of maximum size in the weight class up to 18 kgD – ISO/R2:rear-facing child restraint system for smaller children in the weight class up to 18 kgE – ISO/R1:rear-facing child restraint system for young children in the weight class up to 13 kgF– ISO/L1:left lateral facing position child restraint system (carry-cot)G – ISO/L2:right lateral facing position child restraint system (carry-cot)

Storage81Load compartment
Depending on version, the load
compartment area can be increased
by folding up or removing the seats in
the second and third row.
Vehicle version with seat benches
in second and third row
When loading the following has to be
observed:
● Only store objects on seats of the
third row folded down to the table
position, when the seats in the
second row are also folded down to the table position.
● Bench seat in the second or third
row in the tilted position: the outerseat must not be occupied.
● Single bench seat in the second or third row in the tilted position:
the center seat must not be
occupied.
● Seat in the second row folded down to the table position:
respective seat in the third row must not be occupied.
● Seat in the second row in the tilted position: respective seat inthe third row must not be
occupied.
Folding the passenger seat 3 51.
Folding or removing the rear seats
3 53.
Load compartment cover Do not place any objects on the cover.
Raise the load compartment cover to
remove it.
To install the load compartment cover
insert it in the retainers on both sides.