battery PEUGEOT 1007 2008 User Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2008, Model line: 1007, Model: PEUGEOT 1007 2008Pages: 189, PDF Size: 10.54 MB
Page 111 of 189
7
104
Switching to automated mode Reinitialisation
Following disconnection of the battery,
the gearbox must be reinitialised: The brake pedal must be
pressed while starting the
engine.
Never select neutral
N while
the vehicle is moving.
Only engage reverse gear R with the
vehicle immobilised and the brake
pedal pressed.
In all cases, it is imperative that you
apply the handbrake in order to im-
mobilise the vehicle.
On a steep gradient, it is preferable
to switch to sequential mode.
"Auto sequential" mode
In the automated mode, you can re-
sume control temporarily at any time
using the steering wheel controls.
The use of these controls permits
manual selection of the gears in situa-
tions which require a faster change-
down than that offered in automated
m o d e ( a r r i v a l a t a r o u n d a b o u t , e x i t
from a car park with a steep gradient,
overtaking...).
The gearbox engages the gear
requested if the engine speed
permits it.
"AUTO" is still displayed
on the instrument panel.
After a few moments, the gearbox
again controls the gears automatically.
Stopping the vehicle
Before switching off the engine, you
can:
- move to position N to leave the
gearbox in neutral.
- leave a gear engaged, such as fi r s t o r r e v e r s e .
In both cases, it is imperative that you
apply the handbrake to immobilise
the vehicle. Operating anomaly
W i t h t h e i g n i t i o n o n , t h e fl a s h i n g o f
"AUTO" and lighting of the service
warning light, accompanied by an
audible signal and a message on the
multifunction display, indicate a gear-
box malfunction.
Contact a PEUGEOT dealer without
delay.
If you press the accelera-
tor pedal beyond the point
of resistance, the gearbox
selects the gear below to
permit sharper acceleration. - switch on the ignition,
"AUTO"
and "-" appear on the instrument
panel display,
- press the brake pedal,
- wait approximately 30 seconds until "N" or a gear appears on
the instrument panel display,
- release the brake pedal.
The gearbox is operational again.
Automated mode
After using the sequential mode, you
can return to the automated mode by
selecting position
A .
"AUTO" and the gear engaged ap-
pear on the instrument panel display.
The gearbox then operates in auto-
active mode, without any action on
the part of the driver.
It continuously selects the gear most
suited to the following parameters:
- driving style,
- road characteristics,
- vehicle load.
To optimise driving comfort and ob-
tain the most suitable gear, avoid
sharp variations in the pressure on
the accelerator pedal.
Page 119 of 189
8
113
1.4 LITRE AND 1.6 LITRE 16V PETROL ENGINES
1. Coolant reservoir.
2. Windscreen/headlamp wash
reservoir.
3. P a s s e n g e r c o m p a r t m e n t fi l t e r .
4. B r a k e fl u i d r e s e r v o i r .
5. Fuse box.
6. Battery.
7. A i r fi l t e r .
8. Dipstick.
9. E n g i n e o i l fi l l e r c a p .
Page 120 of 189
8
114
1.4 LITRE HDI AND 1.6 LITRE HDI PEF TURBO DIESEL ENGINES
1. Coolant reservoir.
2. Windscreen/headlamp wash
reservoir.
3. P a s s e n g e r c o m p a r t m e n t fi l t e r .
4. Priming pump.
5. A i r fi l t e r .
6. B r a k e fl u i d r e s e r v o i r .
7. Fuse box.
8. Battery.
9. Dipstick.
10. E n g i n e o i l fi l l e r c a p .
Page 122 of 189
8
116
CHECKS
Handbrake Where the handbrake travel
is too great or there is a re-
duction in the performance
of the system, the hand-
brake should be adjusted,
even between services.
H a v e t h e s y s t e m c h e c k e d b y a
PEUGEOT dealer. Manual gearbox
This does not require an oil
c h a n g e . H a v e t h e l e v e l c h e c k e d
in accordance with the manu-
facturer’s servicing schedule. Air filter and passenger compartment filter
Particle emission filter (Diesel)
It is imperative that maintenance of
t h e p a r t i c l e e m i s s i o n fi l t e r i s c a r r i e d
out by a PEUGEOT dealer in accord-
ance with the manufacturer’s servicing
schedule. Brake pads
Brake pad wear depends
on the style of driving, in
particular for vehicles which
are used in town, over short
distances.
Brake disc/drum wear status
For any information relating to the
wear of the surfaces of the discs and
drums, contact a PEUGEOT dealer. Oil filter
C h a n g e t h e fi l t e r r e g u l a r -
ly, in accordance with the
servicing schedule.
It may be necessary to check
the thickness of the pads,
even between services.
Unless there is a leak in the circuit, a
d r o p i n t h e b r a k e fl u i d l e v e l i n d i c a t e s
that the brake pads are worn.
Only use products recom-
mended by PEUGEOT or
products of equivalent quali-
ty and characteristics.
To ensure best performance
from components as important as the
braking system, PEUGEOT selects
a n d o f f e r s q u i t e s p e c i fi c p r o d u c t s .
To prevent damage to the electrical
units, high pressure washing of the
engine compartment is strictly pro-
hibited .
At the start of winter, have
your battery checked by a
PEUGEOT dealer.
Refer to the servicing book-
let for information on the re-
placement interval for these
components.
Depending on the environment (dusty
atmosphere...) and the use of the ve-
hicle (urban driving...), change them
twice as often, if necessary (refer to
the "Engines" paragraph).
A c l o g g e d p a s s e n g e r c o m p a r t m e n t fi l -
ter may have an adverse effect on the
performance of the air conditioning sys-
tem and produce unpleasant odours.
To check the main levels
and certain components,
in accordance with the
manufacturer’s servic-
ing schedule, refer to the pages of
the servicing booklet which corre-
spond to your vehicle’s engine.
Following prolonged opera-
tion of the vehicle at very
low speed or at idle, you
may, in exceptional circum-
stances, notice steam coming from
the exhaust during acceleration. This
has no effect on the performance of
the vehicle or on the environment.
Battery
Page 129 of 189
9
123
CHANGING A FUSE
The fuse boxes are located under the
fascia on the left-hand side (in the
glove box) and in the engine com-
partment next to the battery. Correct
Removing and fitting a fuse
B e f o r e c h a n g i n g a f u s e y o u m u s t fi n d
out the cause of the fault and have it
put right. The fuse numbers are indi-
cated on the fuse box.
Incorrect * The maxi fuses provide
additional protection for
the electrical systems. All
work must be carried out
by a PEUGEOT dealer.
Fascia fuse box
Open the glove box, then tilt the
cover to open it.
Turn the lever a quarter of a turn,
then push and tilt the box to gain
access to the fuses.
Always replace a faulty
fuse with one of the same
rating.
Fuse N° Rating Functions
FH1 * - Not used.
FH2 * 40 A Trailer Fuse Box.
FH3 * - Not used.
FH4 * 20 A A u d i o a m p l i fi e r .
FH5 * 5 A "Sesame" doors control unit.
Page 130 of 189
9
123
CHANGING A FUSE
The fuse boxes are located under the
fascia on the left-hand side (in the
glove box) and in the engine com-
partment next to the battery. Correct
Removing and fitting a fuse
B e f o r e c h a n g i n g a f u s e y o u m u s t fi n d
out the cause of the fault and have it
put right. The fuse numbers are indi-
cated on the fuse box.
Incorrect * The maxi fuses provide
additional protection for
the electrical systems. All
work must be carried out
by a PEUGEOT dealer.
Fascia fuse box
Open the glove box, then tilt the
cover to open it.
Turn the lever a quarter of a turn,
then push and tilt the box to gain
access to the fuses.
Always replace a faulty
fuse with one of the same
rating.
Fuse N° Rating Functions
FH1 * - Not used.
FH2 * 40 A Trailer Fuse Box.
FH3 * - Not used.
FH4 * 20 A A u d i o a m p l i fi e r .
FH5 * 5 A "Sesame" doors control unit.
Page 134 of 189
9
127
CHANGING A WINDSCREEN WIPER BLADE
Changing a front wiper blade
Lift the wiper arm.
Unclip the blade and remove it.
Fit the new blade.
Push back the wiper arm.
Note: t h e s h o r t e s t b l a d e i s fi t t e d o n
the right-hand wiper arm.
Changing the rear wiper blade
Lift the wiper arm.
Unclip the blade and remove it.
Fit the new blade.
Push back the wiper arm.
ECONOMY MODE FUNCTION
After the engine has stopped, certain
functions (doors, windscreen wipers,
electric windows, courtesy light, audio
equipment, dipped headlamps, etc.)
can only be used for a cumulative
duration of thirty minutes, to prevent
discharging of the battery.
Once the thirty minutes are over, a
message informing you of the switch
to economy mode appears on the
multifunction display and the active
functions are put on standby.
These functions are reactivated auto-
matically next time the vehicle is driven.
To resume the use of these functions
immediately, start the engine and let
it run for a few minutes.
The time available to you will then be
double the duration for which the en-
gine is left running. However, this pe-
r i o d w i l l a l w a y s b e b e t w e e n fi v e a n d
thirty minutes.
Note: if the telephone is being used
when economy mode starts, it will
s t i l l b e p o s s i b l e t o fi n i s h t h e c a l l .
A fl a t b a t t e r y w i l l p r e v e n t t h e
engine from starting.
FITTING/REMOVING THE MAT
When removing the mat on the driv-
er’s side, push the seat as far back
a s p o s s i b l e a n d r e m o v e t h e fi x i n g s .
W h e n r e fi t t i n g , p o s i t i o n t h e m a t c o r -
r e c t l y o n t h e p i n s a n d c l i p t h e fi x i n g s .
Check that the mat is secured cor-
rectly.
To prevent the mat from becoming
caught under the pedals:
- o n l y u s e m a t s s u i t e d t o t h e fi x -ings already present in the ve-
hicle. It is imperative that these
fi x i n g s a r e u s e d .
- n e v e r fi t o n e m a t o n t o p o f a n - other.
Placing the wiper blades in the
special position
Less than a minute after switch-
ing off the ignition, operate the
wipers stalk to position the wiper
blades in the centre of the wind-
screen.
To return the windscreen wipers
to their normal position, switch on
the ignition and operate the wip-
ers stalk.
Page 135 of 189
9
128
BATTERY
The batteries contain harm-
ful substances such as sul-
phuric acid and lead. They
must be disposed of in ac-
cordance with regulations and must
never be discarded with household
waste.
Take used remote control and vehi-
cle batteries to a special collection
point.
To start the vehicle from
another battery:
-
Connect the red cable to the positive
(+) terminals of the two batteries,
- Connect the green or black ca-
ble to the negative (-) terminals
of the two batteries,
- Operate the starter, let the en- gine run,
- Wait for the engine to return to idle, then disconnect the cables.
Before disconnecting the
battery, you must wait for
2 minutes after switching off
the ignition.
Never disconnect a terminal when
the engine is running.
N e v e r c h a r g e a b a t t e r y w i t h o u t fi r s t
disconnecting the terminals.
Close the windows, the sunroof and
the doors before disconnecting the
battery. If they do not operate nor-
mally following reconnection of the
battery, they must be reinitialised
(see sections "Sesame doors" and
"Sunroof"). After every reconnection of the battery:
- switch on the ignition and wait
1 minute before starting to al-
low the electronic systems to be
i n i t i a l i s e d . I f s l i g h t d i f fi c u l t i e s a r e
experienced after this, please
contact a PEUGEOT dealer.
- reinitialise the "2 Tronic" gearbox (refer to the corresponding sec-
tion).
A. Flat battery
B. Slave battery
It is advisable to disconnect
the battery if the vehicle is
not to be used for a period
of more than one month.
To charge the battery using a
battery charger:
- Disconnect the battery,
- Follow the instructions for use
given by the battery charger
manufacturer,
- Reconnect starting with the neg- ative (-) terminal,
- Check that the terminals and connectors are clean. If they are
covered with sulphate (white or
greenish deposit), disconnect
them and clean them.
Page 146 of 189
S
O S SOU R CE
MODE B AND ESC
2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
7
pqr s
0 # MENU LIST
TA
P T Y
DARK
139
RT4
MULTIMEDIA AUDIO EQUIPMENT/TELEPHONE JUKEBOX FUNCTION (10 GB)/GPS (EUROPE)
The SERVICE BOX internet site provides additional
animated information about the RT4. It can be consu lted at
the following address:
http://public.servicebox.peugeot.com.
Simple registration permits access and free consul tation of
the handbook.
The RT4 GPS audio/telephone is coded in such a
way that it will only operate in your vehicle. If i t is to be
installed in another vehicle, contact a PEUGEOT d ealer
f o r c o n fi g u r a t i o n o f t h e s y s t e m .
For safety reasons, it is imperative that the driv er carries
out operations which require prolonged attention wh ile
the vehicle is stationary.
When the engine is switched off and to prevent
discharging of the battery, the RT4 audio/telephone may
switch off after a few minutes. CONTENTS
Page 177 of 189
181
QUESTION SOLUTION
RESPONSE
The stored stations do
not function (no sound,
8 7 . 5 M h z i s d i s p l a y e d . . . ) An incorrect waveband is selected.
Press the BAND AST button to return to the
w a v e b a n d ( A M , F M 1 , F M 2 , F M A S T ) o n w h i c h t h e
stations are stored.
T h e t r a f fi c a n n o u n c e m e n t
( T A ) i s d i s p l a y e d . I d o
n o t r e c e i v e a n y t r a f fi c
information. T u n e t o a r a d i o s t a t i o n w h i c h b r o a d c a s t s t r a f fi c
information.
T h e r a d i o s t a t i o n i s n o t p a r t o f t h e r e g i o n a l t r a f
fi c i n f o r m a t i o n n e t w o r k .
The quality of reception
of the radio station
listened to gradually
deteriorates or the
stored stations do
not function (no
sound, 87.5 Mhz is
d i s p l a y e d . . . ) . The vehicle is too far from the transmitter used b
y the station listened to or
there is no transmitter in the geographical area th rough which the vehicle
is travelling.
T h e e n v i r o n m e n t ( h i l l s , b u i l d i n g s , t u n n e l s , b a s e m e n t c a r p a r k s . . . ) b l o c k
reception, including in RDS mode.
The aerial is absent or has been damaged (for exam ple when going
t h r o u g h a c a r w a s h o r i n t o a n u n d e r g r o u n d c a r p a r k ) . Activate the RDS function to enable the system
to check whether there is a more powerful
transmitter in the geographical area.
This phenomenon is normal and does not
indicate a failure of the audio equipment.
Have the aerial checked by a PEUGEOT dealer.
Sound cut-outs of 1
to 2 seconds in radio
mode. During this brief sound cut-out, the RDS searches
for any frequency
permitting better reception of the station. Deactivate the RDS function if the phenomenon
is too frequent and always on the same route.
With the engine off,
the audio equipment
switches off after a few
minutes of use. When the engine is switched off, the audio equipme
nt operating time
depends on the battery charge.
The switch-off is normal: the audio equipment swit ches to economy mode
and switches off to prevent discharging of the vehi cle's battery. Start the vehicle's engine to increase the battery
charge.
The message "the audio
system is overheated"
appears on the display. Switch the audio system off for a few minutes to
allow the system to cool.
In order to protect the installation if the surrou
nding temperature is too
high, the audio equipment switches to an automatic thermal protection
mode leading to a reduction of the volume or stoppi ng of the playing of the
CD.