wheel PEUGEOT 1007 2008 Owner's Manual

9
117
Parking the vehicle
- If possible, park the vehicle on level, stable and non-slippery
ground.
- It is imperative that you ensure that the occupants get out of the
vehicle and wait in a safe loca-
tion.
- Apply the handbrake, switch off the ignition and engage fi rst or
reverse gear (position R for the
"2 Tronic" gearbox).
CHANGING A WHEEL

1. Jack with integrated handle.

2. Chock.

3. Wheelbrace.

4. Extension.

5. "Bolt cover" tool.

6. Removable towing eye. Access to the spare wheel and
the jack
The wheel is located outside the ve-
hicle, under the rear fl oor, supported
by a metal carrier.
- Unclip the cover to gain access
to the spare wheel carrier retain-
ing bolt, located on the inside
near the closing system.
- Using the wheelbrace 3 and the
extension 4 , slacken the spare
wheel carrier retaining bolt.
- Lift the carrier to release the hook rearwards, then lower it.
- Remove the spare wheel and the box.
- Remove the jack 1 from the box.
Tools provided
The jack is stored in a box in the cen-
tre of the spare wheel. The chock is
fi xed on the side of the box.
The other tools are stored in a case
in the left boot trim.
Note: if your vehicle is fi tted with a
towbar, the case is stored in the left
storage tray (located in the fl oor of
the rear footwell).

9
118
Removing a wheel
-
Place the chock 2 (integrated with the
box) at the rear of the wheel diagonal-
ly opposite the wheel to be changed.
- Remove the wheel trim, using the wheelbrace 3 , by pulling at
the valve passage hole.
-
Remove the chrome-plated bolt
covers and the plastic cover from
the bolts using the "bolt cover" tool 5
(Special features of alloy wheels).
- Slacken the wheel bolts.
- Place the jack 1 under one of the
four locating points A on the sub-
frame closest to the wheel to be
changed. Ensure that the entire
surface of the jack base plate is
in contact with the ground.
-
Extend the jack, completely unscrew
the bolts and remove the wheel.
Refitting the wheel
- Position the wheel on the hub.
- Lightly pre-tighten the bolts us- ing the wheelbrace 3 .
-
Compress the jack 1 and release it.
- Fully tighten the bolts using the
wheelbrace.
- Replace the trim, starting at the valve passage hole, and press it
on using the palm of the hand.
For your safety, always
change a wheel:
- Stow the tools in the case, then
put it back in the left boot trim.
The jack and the tool kit are specifi c
to your vehicle. Do not use them for
other purposes.
Replacing the wheel in the
carrier
- Replace the jack 1 in the box.
- Replace the box in the wheel.
- Replace the wheel in the carrier.
- Lift the wheel then the carrier and reposition the hook.
- Do not forget to fully tighten the spare wheel carrier retaining bolt. After changing the wheel
- Have the tightening of the bolts
and the pressure of the spare
tyre checked as soon as possi-
ble by a PEUGEOT dealer.
-
Do not exceed its maximum autho-
rised speed: 50 mph (80 km/h).
- Have the punctured tyre repaired and replace it on the vehicle as
soon as possible.
- 15 and 16 inch punctured wheels cannot be placed in the carrier.
- on level, stable and non-slippery
ground,
- with the handbrake applied,
- with fi rst or reverse gear engaged (position R for the "2 Tronic"
gearbox),
- with the vehicle chocked,
- never go underneath a vehicle raised using a jack (use an axle
stand).

9
119
Special features of alloy
wheels Fitting the spare wheel
If your vehicle is fi tted with a steel
spare wheel, when fi tting it, it is
nor-
mal when tightening the bolts to no-
tice that the washers do not come
into contact with the rim. The spare
wheel is secured by the cone shape
of each bolt. This anti-theft socket was
given to you on delivery of
your vehicle along with the
duplicate keys.
Make a careful note of the code
number engraved on the head of the
anti-theft socket. This will enable you
to obtain a duplicate socket from a
PEUGEOT dealer.
Fitting snow tyres
If you fi t snow tyres mounted on steel
wheels onto your vehicle, it is es-
sential to use special bolts available
from PEUGEOT dealers.

Wheels equipped with 195/50R16
tyres cannot be fi tted with snow
chains.

For further information, contact a

PEUGEOT dealer.
Bolt covers
Alloy wheel bolts are covered by
chrome trims.
Use the yellow tool to remove the
trims before slackening the bolts. Anti-theft bolts
If your wheels are fi tted with an anti-
theft bolt (one per wheel), the chrome
trim must be removed before un-
screwing the bolt using the anti-theft
socket and the wheelbrace.

9
122
Rear lights

1. Brake/side lights
(P21 W/5 W).

2. Direction indicators
(P21 W).

3. Reversing light
(P21 W), left side.
Fog lamp (P21 W), right side.
These 4 bulbs are changed by re-
moving the light:

 Remove the access fl ap in the
corresponding boot side trim to
access the light,

 Remove the two light fi xing nuts
inside the boot,

 Unclip the harness,

 Remove the light pressing on the
retaining tabs,

 Remove the seal,
 Remove the bulb holder moving
aside the two tabs A ,

 Turn the bulb a quarter of a turn,

 Remove the bulb and change it.

Note: if necessary, use the wheel-
brace to remove the nuts.
When refi tting, proceed in the re-
verse order and take care to position
the bulb holder, the seal and the light
correctly. Third brake light
(4 W 5 W bulbs)

 Using a 10 mm box spanner, un-
screw the 2 fi xing nuts A .

 Release the lamp unit by push-
ing it outwards.

 Disconnect the connector and
the rear wash-wipe pipe.

 Turn the bulb holder a quarter of
a turn and remove it.

 Remove the bulb and change it.
When refi tting, proceed in the reverse
order and ensure that the lamp unit
seal and the rear wash-wipe pipe have
been put back in place correctly.
Do not tighten the nuts more than is
necessary at the risk of breaking the
light.
Number plate lights (W 5 W)

 Insert a thin screwdriver into one
of the external holes of the lens.

 Push it outwards to unclip it.

 Remove the lens.

 Remove the bulb and change it.

9
124

Fuse N° Rating
Functions

1 15 A Rear wiper.

3 5 A Air bags and pre-tensioners control unit.

4 10 A Diagnostic socket - Clutch switch - Steering wheel angle sensor
-
Particle emission fi lter pump.

5 30 A Electric windows - Sunroof.

6 - Not used.

7 5 A Courtesy light - Glove box light.

8 20 A Tyre under-infl ation detection control unit - Folding of t
he electric mirrors - Alarm siren -
Multifunction display - Alarm control unit - Audio equipment - Aud io/telephone.

9 30 A Audio equipment - Lighter/12 V socket (100 W max.).

10 15 A Steering wheel controls.

11 15 A Diagnostic socket - Low current ignition switch - Motorised strik ers.

12 15 A Air bags and pre-tensioners control unit - Rain/brightness sens or.

13 5 A ABS relay - Speed sensor - Engine Fuse Box - "2 Tronic" gear lever - Brake switch.

14 15 A Parking assistance control unit - "Sesame" doors control unit and swit
ches -
Instrument panel - Seat belt warning lights bar - Air condition ing control panel -
Headlamp adjustment - Hands-free kit.

15 30 A Locking - Deadlocking - Unlocking.

17 40 A Rear screen and exterior mirrors demisting.

SH - PARC shunt.

9
129
TOWING YOUR VEHICLE

From the rear:

 Unclip the side of the cover using
the fl at part of the towing eye,

 Screw in the towing eye until it
locks. When towing with the en-
gine switched off, there is no
braking assistance.
Special features of the
"2 Tronic" gearbox
When towing with four wheels on the
ground, the following rules must be
obeyed:
- gear lever in position
N ,
- tow the vehicle at less than 30 mph (50 km/h) over a maximum dis-
tance of 30 miles (50 km).
- do not add oil to the gearbox.

From the front:

 Unclip the bottom of the cover,
using the fl at part of the towing
eye.

 Screw in the towing eye until it
locks. Lifting
(2 wheels only on the road)
It is preferable to raise the vehicle by
the wheels.

Never use the radiator crossmem-
ber.
Without lifting
(4 wheels on the road)
You should always use a towbar.
The removable towing eye is stored
in the tool case, located in the left
boot trim.
Vehicles fitted with a manual
gearbox (diesel version)
In the case of vehicles fi tted with a
manual gearbox, the gear lever must
be in the neutral position.
Failure to observe this special condi-
tion may result in damage to certain
braking components and the absence
of braking assistance the next time
the engine is started.

9
131
ACCESSORIESFOR YOUR 1007
A wide range of accessories recom-
mended by PEUGEOT and original
parts are offered by the Network.
They all benefi t from PEUGEOT’s
recommendation.
These accessories and parts, having
been tested and approved for reli-
ability and safety, are all adapted to
your PEUGEOT vehicle. The fi tting of electrical equip-
ment or accessories which
are not recommended by
PEUGEOT may result in a
failure of your vehicle’s electronic
system.
Please note this specifi c warning.
You are advised to contact a repre-
sentative of the Marque to be shown
the range of recommended equip-
ment and accessories.
Depending on the country in which
the vehicle is sold, it is compulsory to
have a safety jacket, warning trian-
gle and spare bulbs available in the
vehicle.

"Protection": anti-theft
alarm, engraved windows,
wheel anti-theft devices,
system which assists with
the identifi cation of a stolen
vehicle, fi rst aid kit, warn-
ing triangle, high visibility
safety jacket, fog lamps kit,
snow chains, non-skid cov-
ers, audible rear parking
assistance.

"Touring": central arm-
rest, storage under the rear
shelf, mats * , boot tray, sun
blinds.
For leisure pursuits: roof
bars, transportation ac-
cessories (bicycle carrier,
ski carrier), roof box, child
seats and booster cushions, audio/
telephone console, cool box.

"In-Car Technology": hands-
free kits, satellite navigation sys-
tems, CD changer, DVD player,
multimedia, audio equipment,
speakers, auxiliary audio socket
permitting the connection of a
portable MP3 player (compat-
ible with RD4), USB Box.

"Styling": seat covers, al-
loy wheels, wheel trims,
spoiler, styling strips, door
spoilers, sill protectors,
aluminium footrest, rear si-
lencer, exhaust tail pipe.

"Universal": windscreen
wash fl uid, interior and ex-
terior cleaning and mainte-
nance products. You can obtain "Van" conver-
sion kits for conversion from
a private vehicle to a van.
You can obtain other
"Cameleo" customising kits
from PEUGEOT dealers.
You will be offered either a
complete kit, like the original kit, or a
partial kit consisting of the vent trims
only.
Should you need to change one or
more elements of the Cameleo kit of
your vehicle, due to damage..., you
will be offered replacement elements
from the exchange kits available at
that time.
This product range offered by PEUGEOT
Accessories is structured around 5 catego-
ries: PROTECTION - TOURING - IN-CAR
TECHNOLOGY - STYLING - UNIVERSAL.

* To prevent jamming under the pedals:
- ensure that the mat is positioned and secured correctly,
- never fi t one mat on top of an- other.
Trailer towbar which must be fi tted by
the PEUGEOT network.

1010
138
IDENTIFICATION FEATURES OF YOUR 1007

A. Manufacturer’s plate.

B. Serial number on the
bodywork (under the
bonnet, at the centre of the
crossmember).

C. Serial number on the fascia
(on the small aperture,
left-hand side).

D. Tyres and paint colour
reference. The label
D on the pillar, near the
left-hand door striker, indicates:
- the wheel and tyre sizes,
- the brands of tyres approved by the manufacturer,
- the tyre pressures (the tyre
pressure must be checked
when the tyre is cold, at least
once a month) ,
- the paint colour reference.
Wheels equipped with 195/50R16
tyres cannot be fi tted with snow
chains.

Contact a PEUGEOT dealer for
information.
Low tyre pressures increase
fuel consumption.

2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
7
pqrs
0 #
ESC
MENU LIST
ESC
MENU LIST
2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
r
7
pq s
0
#
D
2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
r
7
pq s
0 #
D
2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
r
7
pq s
0 #
11
22
33
44
55
66
D
2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
r
7
pq s
0 #D
2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
r
7
pq s
0 #
D
2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
r
7
pq s
0 #
06
160
TELEPHONE
CALLING A CONTACT
Turn the dial and select the DIAL
function. Press the PICK UP button to display
the superimposed telephone menu.
Press the dial to confi rm the selection.
Dial the telephone number of your
contact using the alphanumeric
keypad. Press the PICK UP button to call the
number dialled.
Press the HANG UP button to end
the call.
ACCEPTING OR REFUSING A CALL Press the PICK UP button to accept
a call.
Press the HANG UP button to refuse
a call.
DIAL
Press the end of the steering wheel stalk for more
than 2 seconds to access the telephone menu:
calls log, directory, voice mailbox.

07
162
RADIO: selection of the previous stored station.
MP3/JUKEBOX: selection of the previous directory.
CD CHANGER: selection of the previous CD.
Selection of the previous item on a menu.
RADIO: selection of the next stored station.
MP3/JUKEBOX: selection of the next directory.
CD CHANGER: selection of the next CD.
Selection of the next item on a menu. RADIO: automatic search for a higher frequency.
CD/MP3/JUKEBOX/CD CHANGER: selection of the
next track.
CD/CD CHANGER: continuous press: fast forwards
play.
RADIO: automatic search for a lower frequency.
CD/MP3/JUKEBOX/CD CHANGER: selection of the
previous track.
CD/CD CHANGER: continuous press: fast backwards pl ay.
- Change of sound source.
- Confi rmation of a selection.
- Pick up/Hang up the telephone.
- Press for more than 2 seconds:
access to the telephone menu.
Volume increase.
Volume decrease.
CONTROL SHORT-CUTS
STEERING WHEEL CONTROLS
Mute: by pressing the volume
increase and decrease
buttons simultaneously.
The sound is restored by
pressing one of the two
volume buttons.