battery Peugeot 1007 Dag 2008.5 User Guide

5
86
LIGHTS STALK
Lights off Automatic switching on
of lights.
Side lights Dipped/main beam
headlamps Dipped/Main beam change
Pull the stalk fully towards you.
Front fog lamps and rear
fog lamp
Rotate the ring
B or C forwards to
switch on and backwards to switch
off. The status is displayed by the in-
dicator light on the instrument panel.
Vehicles fi tted with a rear fog
lamp (ring B)
Rear fog lamp
Vehicles fi tted with front fog
lamps and a rear fog lamp (ring C) Front fog lamps (1st rotation
of the ring forwards)
These operate with the side lights
and dipped headlamps.
Lights on
With the ignition off, a buzzer sounds
when the driver's door is opened, if
you have left your lights on.
If the dipped headlamps remain
on, with the ignition off, they will
be switched off automatically after
thirty minutes maximum to prevent
discharging of the battery.
This can only operate with the dipped
and main beam headlamps.
Front and rear lights
Selection is by turning ring
A .

7
104
Switching to automated mode Reinitialisation
Following disconnection of the battery,
the gearbox must be reinitialised: The brake pedal must be
pressed while starting the
engine.
Never select neutral N while the vehi-
cle is moving.
Only engage reverse gear R with the
vehicle immobilised and the brake
pedal pressed.
In all cases, it is imperative that
you apply the handbrake in order to
immobilise the vehicle.
On a steep gradient, it is preferable
to switch to sequential mode.
"Auto sequential" mode
In the automated mode, you can
resume control temporarily at any
time using the steering wheel controls.
The use of these controls permits
manual selection of the gears in situ-
ations which require a faster change-
down than that offered in automated
mode (arrival at a roundabout, exit
from a car park with a steep gradient,
overtaking...).
The gearbox engages the gear re-
quested if the engine speed permits
it.
"AUTO" is still displayed on the
instrument panel.
After a few moments, the gearbox
again controls the gears automatically.
Stopping the vehicle
Before switching off the engine, you
can:
- move to position N to leave the
gearbox in neutral.
- leave a gear engaged, such as fi rst or reverse.
In both cases, it is imperative that
you apply the handbrake to immobi-
lise the vehicle. Operating anomaly
With the ignition on, the fl ashing of

"AUTO" and lighting of the service
warning light, accompanied by an
audible signal and a message on the
multifunction display, indicate a gear-
box malfunction.
Contact a PEUGEOT dealer without
delay.
If you press the accelerator
pedal beyond the point of
resistance, the gearbox
selects the gear below to
permit sharper acceleration. - switch on the ignition,
"AUTO"
and "-" appear on the instrument
panel display,
- press the brake pedal,
- wait approximately 30 seconds until "N" or a gear appears on
the instrument panel display,
- release the brake pedal.
The gearbox is operational again.
Automated mode
After using the sequential mode, you
can return to the automated mode by
selecting position
A .

"AUTO" and the gear engaged appear
on the instrument panel display.
The gearbox then operates in auto-
active mode, without any action on
the part of the driver.
It continuously selects the gear most
suited to the following parameters:
- driving style,
- road characteristics,
- vehicle load.
To optimise driving comfort and
obtain the most suitable gear, avoid
sharp variations in the pressure on
the accelerator pedal.

8
113
1.4 LITRE AND 1.6 LITRE16V PETROL ENGINES

1. Coolant reservoir.

2. Windscreen/headlamp wash
reservoir.

3. Passenger compartment fi lter.

4. Brake fl uid reservoir.

5. Fuse box.

6. Battery.

7. Air fi lter.

8. Dipstick.

9. Engine oil fi ller cap.

8
114
1.4 LITRE HDI AND 1.6 LITRE HDI PEF TURBO DIESEL ENGINES

1. Coolant reservoir.

2. Windscreen/headlamp wash
reservoir.

3. Passenger compartment fi lter.

4. Priming pump.

5. Air fi lter.

6. Brake fl uid reservoir.

7. Fuse box.

8. Battery.

9. Dipstick.

10. Engine oil fi ller cap.

8
116
CHECKS
Handbrake Where the handbrake travel
is too great or there is a re-
duction in the performance
of the system, the hand-
brake should be adjusted,
even between services.
Have the system checked by a PEUGEOT
dealer.
Air filter and passenger compartment filter
Particle emission filter (Diesel)
It is imperative that maintenance of
the particle emission fi lter is carried
out by a PEUGEOT dealer in accord-
ance with the manufacturer's servicing
schedule.
Brake pads
Brake pad wear depends
on the style of driving, in
particular for vehicles which
are used in town, over short
distances.
Brake disc/drum wear status
For any information relating to the
wear of the surfaces of the discs and
drums, contact a PEUGEOT dealer. Oil filter
Change the fi lter regularly, in
accordance with the servic-
ing schedule.
It may be necessary to
check the thickness of the
pads, even between services.
Unless there is a leak in the circuit, a drop in the brake fl uid level
indicates that the brake pads are
worn.
At the start of winter, have
your battery checked by a
PEUGEOT dealer.
Refer to the servicing book-
let for information on the
replacement interval for
these components.
Depending on the environ-
ment (dusty atmosphere...) and the
use of the vehicle (urban driving...),

change them twice as often, if ne
cessary (refer to the "Engines" para-
graph).
A clogged passenger compartment
fi lter may have an adverse effect on
the performance of the air condition-
ing system and produce unpleasant
odours.
Following prolonged opera-
tion of the vehicle at very
low speed or at idle, you
may, in exceptional circum-
stances, notice steam coming from
the exhaust during acceleration. This
has no effect on the performance of
the vehicle or on the environment.
Battery
Manual gearboxThis does not require an
oil change. Have the level
checked in accordance with
the manufacturer's servicing
schedule.
Only use products recom-
mended by PEUGEOT or
products of equivalent qual-
ity and characteristics.
To ensure best performance from
components as important as the
braking system, PEUGEOT selects
and offers quite specifi c products.
To prevent damage to the electri-
cal units, high pressure washing of
the engine compartment is strictly
prohibited .
To check the main levels
and certain components,
in accordance with the
manufacturer's servicing
schedule, refer to the pages of the
servicing booklet which correspond
to your vehicle's engine.

9
127
CHANGING A WINDSCREEN WIPER BLADE
Changing a front wiper blade

 Lift the wiper arm.

 Unclip the blade and remove it.

 Fit the new blade.

 Push back the wiper arm.

Note: the shortest blade is fi tted on
the right-hand wiper arm.
Changing the rear wiper blade

 Lift the wiper arm.

 Unclip the blade and remove it.

 Fit the new blade.

 Push back the wiper arm.
ECONOMY MODE FUNCTION
After the engine has stopped, certain
functions (doors, windscreen wipers,
electric windows, courtesy light, audio
equipment, dipped headlamps, etc.)

can only be used for a cumulative
duration of thirty minutes, to prevent
discharging of the battery.
Once the thirty minutes are over, a
message informing you of the switch
to economy mode appears on the
multifunction display and the active
functions are put on standby.
These functions are reactivated
automatically next time the vehicle is
driven.
To resume the use of these functions
immediately, start the engine and let
it run for a few minutes.
The time available to you will then be
double the duration for which the en-
gine is left running. However, this pe-
riod will always be between fi ve and
thirty minutes.

Note: if the telephone is being used
when economy mode starts, it will
still be possible to fi nish the call.
A fl at battery will prevent the
engine from starting.
FITTING/REMOVING THE MAT
When removing the mat on the dri-
ver's side, push the seat as far back
as possible and remove the fi xings.
When refi tting, position the mat
correctly on the pins and clip the
fi xings. Check that the mat is secured
correctly.
To prevent the mat from becoming
caught under the pedals:
- only use mats suited to the fi xings already present in the
vehicle. It is imperative that these
fi xings are used.
- never fi t one mat on top of another.
Placing the wiper blades in the
special position


Less than a minute after switching
off the ignition, operate the wip-
ers stalk to position the wiper
blades in the centre of the wind-
screen.

To return the windscreen wipers
to their normal position, switch on
the ignition and operate the wipers
stalk.

9
128
BATTERY
The batteries contain harmful
substances such as sulphuric
acid and lead. They must be
disposed of in accordance
with regulations and must never be
discarded with household waste.
Take used remote control and vehi-
cle batteries to a special collection
point.
To start the vehicle from
another battery:
-
Connect the red cable to the positive
(+) terminals of the two batteries,
- Connect the green or black ca- ble to the negative (-) terminals
of the two batteries,
- Operate the starter, let the en- gine run,
- Wait for the engine to return to idle, then disconnect the cables.
Before disconnecting the
battery, you must wait for
2 minutes after switching off
the ignition.
Never disconnect a terminal when
the engine is running.
Never charge a battery without fi rst
disconnecting the terminals.
Close the windows, the sunroof and
the doors before disconnecting the
battery. If they do not operate nor-
mally following reconnection of the
battery, they must be reinitialised
(see sections "Sesame doors" and
"Sunroof"). After every reconnection of the bat-
tery:
- switch on the ignition and wait
1 minute before starting to al-
low the electronic systems to be
initialised. If slight diffi culties are
experienced after this, please
contact a PEUGEOT dealer.
-
reinitialise the "2 Tronic" gearbox
(refer to the corresponding section).

A. Flat battery

B. Slave battery
It is advisable to disconnect
the battery if the vehicle is
not to be used for a period
of more than one month.
To charge the battery using a
battery charger:
- Disconnect the battery,
- Follow the instructions for use
given by the battery charger
manufacturer,
- Reconnect starting with the nega- tive (-) terminal,
- Check that the terminals and connectors are clean. If they are
covered with sulphate (white or
greenish deposit), disconnect
them and clean them.