ECO mode Peugeot 1007 Dag 2008.5 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2008.5, Model line: 1007 Dag, Model: Peugeot 1007 Dag 2008.5Pages: 194, PDF Size: 11.23 MB
Page 13 of 194
FAMILIARISATION
DRIVING SAFELY
Speed limiter Cruise control
1. Speed limiter mode Selection/
O f f .
2. Decreasing of the programmed
v a l u e .
3. Increasing of the programmed
v a l u e .
4. S p e e d l i m i t e r O n / O f f .
1. Cruise control mode Selection/
O f f .
2. Decreasing of the programmed
v a l u e .
3. Increasing of the programmed
v a l u e .
4. C r u i s e c o n t r o l O n / O f f .
In order to be programmed or activat-
ed, the vehicle speed must be above
25 mph (40 km/h), with at least fourth
gear engaged on the manual gear-
box (second gear for the "2 Tronic"
g e a r b o x ) .
107 Display on the instrument panel
The cruise control or speed limiter
mode appears on the instrument
p a n e l w h e n i t i s s e l e c t e d .
Cruise control
Speed limiter
The values must be set with the
e n g i n e r u n n i n g .
105
Page 20 of 194
1
23
L a c k o f o i l
If "OIL" fl a s h e s a n d t h e s e r v i c e w a r n -
ing light comes on, accompanied by
an audible signal and a message on
the multifunction display, this indicates
a lack of oil which could damage the
engine.
I f t h e l a c k o f o i l i s c o n fi r m e d b y a
check using the dipstick, it is essential
that the level is topped up.
E n g i n e o i l l e v e l i n d i c a t o r
When the ignition is switched on, the
engine oil level is indicated for approxi-
mately 5 seconds after the service indi-
cator display.
O i l l e v e l g a u g e f a u l t
Check the oil level using the dipstick.
If "OIL --" fl a s h e s , t h i s i n d i c a t e s a
malfunction of the engine oil level
gauge.
Consult a PEUGEOT dealer.
INSTRUMENT PANEL DISPLAY
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator
- total distance recorder (total and trip distances).
The level read on the dipstick
will only be correct if the
vehicle is on level ground
and the engine has been off
for more than 15 minutes.
O i l l e v e l c o r r e c t
N o t e : the trip distance is displayed
for thirty seconds, when the ignition is
switched off, on opening and closing
the driver's door as well as on locking
the vehicle.
It also displays the "2 Tronic" gear-
box positions and operating modes
selected, as well as the information
relating to the cruise control or speed
limiter when one of these functions is
active.
Page 45 of 194
3
48
AUTOMATIC AIR CONDITIONING
The air conditioning can only operate when the engine is running.
1. Automatic "comfort" programme
We recommend that you use this
mode, it provides optimised auto-
matic control of all of the following
functions: passenger compartment
t e m p e r a t u r e , a i r fl o w , a i r d i s t r i b u t i o n
and air intake, in accordance with the
comfort value that you have chosen.
This system is designed to operate
effectively in all seasons, with the
windows closed. Press the
"AUTO" button.
The "AUTO" symbol is dis-
played. The automatic comfort pro-
g r a m m e m a y n o t b e s u f fi c i e n t
for rapid de-icing or demisting
of the windscreen and side
windows (humidity, several
passengers, ice, etc.).
In this case, select the automatic visi-
bility programme. The button 3 indicator
light comes on.
The system automatically controls
t h e a i r c o n d i t i o n i n g a n d t h e fl o w o f a i r
and provides optimum distribution of
the ventilation to the windscreen and
side windows. It deactivates the air
recirculation.
To exit this programme, press button 3
again or press the "AUTO" button, the
indicator light on the button is switched
off and "AUTO" is displayed.
Note: for your comfort, when the en-
gine is switched off, the settings are
retained until the engine is switched
on again, if the temperature in the
passenger compartment has not al-
t e r e d s i g n i fi c a n t l y ; o t h e r w i s e , o p e r a -
tion resumes in automatic mode.
When the engine is cold, to prevent
too great a distribution of cold air, the
a i r fl o w w i l l o n l y r e a c h i t s o p t i m u m
level gradually. 3. Automatic "visibility"
programme
Automatic operation
The value indicated on
the display corresponds
to a level of comfort
and not to a tempera-
ture in degrees Celsius
or Fahrenheit.
2. Temperature adjustment On entering the vehicle, if
the interior temperature is
much colder or warmer than
is comfortable, there is no
need to change the value displayed
in order to reach the required level of
comfort. The system eliminates the
temperature difference automatically
and as quickly as possible.
Press the
"+" and "-" buttons to
change this value. A setting around the
value 22 enables optimum comfort to
be obtained. However, depending on
your requirements, a setting between
18 and 24 is usual.
Page 77 of 194
4
78
ELECTRIC WINDOWS
1. Driver's electric window
switch.
2. Passenger electric window
switch. You can close all of the
windows using the remote
control when locking (refer
to the chapter "Access - §
Remote control key").
The electric window switches are not
active when the door concerned is
open.
The movement of a window stops if
the door is opened. A second action
on the electric window switch will
only be taken into account when the
door is closed.
Safety auto-reverse
In automatic mode, when the window
rises and meets an obstacle, it stops
and partially lowers again. In the case of unwanted
opening of the window on
closing or if the window will
not rise, lower it completely
and raise it again immediately, by
pulling the switch until the window
closes completely. Continue to press
the switch for approximately one
second after closing.
The safety auto-reverse function
is not operational during these
operations.
Electric window
Press or pull switch 1 . The
window stops as soon as the
switch is released.
One-touch electric window
with safety auto-reverse
You have two options: -
Manual mode:
Press or pull switch 1 gently.
The window stops as soon
as the switch is released.
- Automatic mode:
Press or pull switch 1 fully. The win-
dow opens or closes completely
when the switch is released.
Pressing the switch again stops the
movement of the window.
Note: the electrical functions of the
one-touch electric windows are de-
activated approximately one minute
after the ignition is switched off.
Note: the electrical functions of the
electric windows are deactivated
approximately 45 seconds after the
ignition is switched off, or when a
door is opened. Always remove the key from
the ignition when leaving
the vehicle, even for a short
time.
In the event of contact when operating
the windows, you must reverse the
movement of the window. To do this,
press the switch concerned.
When the driver operates the pas-
senger window switches, he must
ensure that no one is preventing cor-
rect closing of the window.
The driver must ensure that passengers
use the electric windows correctly.
Be aware of children when operating
the windows.
Page 88 of 194
5
88
Daytime lights *
On vehicles which are equipped with daytime lights, the dipped headlamps come on when the vehicle is started.
A u t o m a t i c s w i t c h i n g o n o f
lights
The side lights and dipped beam headlamps switch on automatically if the light is poor and when the wind-screen wipers operate continuously. They switch off when the light be-comes bright enough or the wind-screen wipers are switched off.
I n f o g g y w e a t h e r o r i n s n o w , t h e b r i g h t n e s s s e n - s o r c a n d e t e c t s u f fi c i e n t l i g h t , t h e l i g h t s w i l l n o t come on automatically.
Do not cover the brightness s e n s o r , c o u p l e d w i t h t h e r a i n s e n s o r , l o c a t e d i n t h e c e n t r e o f t h e w i n d s c r e e n b e h i n d t h e i n t e r i o r mirror. It is used for automatic s w i t c h i n g o n o f t h e l i g h t s .
C o u p l i n g w i t h t h e F o l l o w M e
Home lighting
The association with the automatic lighting function provides the follow me home lighting with the following additional options:
- selection of maintaining of the lighting for a duration of 15, 30 or 60 seconds in the vehicle parameters of the multifunction d i s p l a y c o n fi g u r a t i o n m e n u (except in the case of the monochrome display A for which the duration is pre-set),
- automatic activation of the follow me home lighting when the automatic lighting function is in operation.
Activation
Turn the lighting control to the " AUTO " position.
Disarming
Turn the lighting control to a position other than " AUTO ".
Operating fault
If the brightness sensor does not function correctly, the lights come on accompanied by the service warning light, an audible signal and a message on the multifunction display.
Consult a PEUGEOT dealer.
Operating fault
If the brightness sensor does not function correctly, the lights come on accompanied by the service warning light, an audible signal and a messa-ge on the multifunction display.
Contact a PEUGEOT dealer.
Do not cover the brightness sensor, coupled with the rain sensor, located in the centre of the windscreen behind the interior mirror; the as-sociated functions would no longer be controlled.
This warning light comes on on the instrument panel.
The instruments and controls (ins-trument panel, multifunction display, air conditioning control panel, ...) are only lit on switching to the automa-tic switching on of the lights mode or when the lights are switched on ma-nually.
* According to country.
Page 89 of 194
5
88
Daytime lights *
On vehicles which are equipped with daytime lights, the dipped headlamps come on when the vehicle is started.
A u t o m a t i c s w i t c h i n g o n o f
lights
The side lights and dipped beam headlamps switch on automatically if the light is poor and when the wind-screen wipers operate continuously. They switch off when the light be-comes bright enough or the wind-screen wipers are switched off.
I n f o g g y w e a t h e r o r i n s n o w , t h e b r i g h t n e s s s e n - s o r c a n d e t e c t s u f fi c i e n t l i g h t , t h e l i g h t s w i l l n o t come on automatically.
Do not cover the brightness s e n s o r , c o u p l e d w i t h t h e r a i n s e n s o r , l o c a t e d i n t h e c e n t r e o f t h e w i n d s c r e e n b e h i n d t h e i n t e r i o r mirror. It is used for automatic s w i t c h i n g o n o f t h e l i g h t s .
C o u p l i n g w i t h t h e F o l l o w M e
Home lighting
The association with the automatic lighting function provides the follow me home lighting with the following additional options:
- selection of maintaining of the lighting for a duration of 15, 30 or 60 seconds in the vehicle parameters of the multifunction d i s p l a y c o n fi g u r a t i o n m e n u (except in the case of the monochrome display A for which the duration is pre-set),
- automatic activation of the follow me home lighting when the automatic lighting function is in operation.
Activation
Turn the lighting control to the " AUTO " position.
Disarming
Turn the lighting control to a position other than " AUTO ".
Operating fault
If the brightness sensor does not function correctly, the lights come on accompanied by the service warning light, an audible signal and a message on the multifunction display.
Consult a PEUGEOT dealer.
Operating fault
If the brightness sensor does not function correctly, the lights come on accompanied by the service warning light, an audible signal and a messa-ge on the multifunction display.
Contact a PEUGEOT dealer.
Do not cover the brightness sensor, coupled with the rain sensor, located in the centre of the windscreen behind the interior mirror; the as-sociated functions would no longer be controlled.
This warning light comes on on the instrument panel.
The instruments and controls (ins-trument panel, multifunction display, air conditioning control panel, ...) are only lit on switching to the automa-tic switching on of the lights mode or when the lights are switched on ma-nually.
* According to country.
Page 94 of 194
5
91
COURTESY LIGHT
1. Front courtesy light
2. Map reading lights In the permanently on posi-
tion, there are different dura-
tions of lighting:
Boot light
The boot light is located in the left
boot trim.
It comes on automatically when the
boot is opened and switches of auto-
matically when the boot is closed.
Front courtesy light Permanently off.
Permanently on.
In this position, the courtesy
light comes on gradually:
- when the vehicle is unlocked,
- when the key is removed from the ignition,
- when the remote control locking button is pressed, in order to
locate your vehicle.
It switches off gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- 30 seconds after the last door is closed. Map reading lights
With the ignition on, press
the corresponding switch 2 .
- when the ignition is off, approxi-
mately ten minutes,
- in energy economy mode, ap- proximately thirty seconds,
- when the engine is running, no limit.
Page 111 of 194
7
104
Switching to automated mode Reinitialisation
Following disconnection of the battery,
the gearbox must be reinitialised: The brake pedal must be
pressed while starting the
engine.
Never select neutral N while the vehi-
cle is moving.
Only engage reverse gear R with the
vehicle immobilised and the brake
pedal pressed.
In all cases, it is imperative that
you apply the handbrake in order to
immobilise the vehicle.
On a steep gradient, it is preferable
to switch to sequential mode.
"Auto sequential" mode
In the automated mode, you can
resume control temporarily at any
time using the steering wheel controls.
The use of these controls permits
manual selection of the gears in situ-
ations which require a faster change-
down than that offered in automated
m o d e ( a r r i v a l a t a r o u n d a b o u t , e x i t
from a car park with a steep gradient,
overtaking...).
The gearbox engages the gear re-
quested if the engine speed permits
it.
"AUTO" is still displayed on the
instrument panel.
After a few moments, the gearbox
again controls the gears automatically.
Stopping the vehicle
Before switching off the engine, you
can:
- move to position N to leave the
gearbox in neutral.
- leave a gear engaged, such as fi r s t o r r e v e r s e .
In both cases, it is imperative that
you apply the handbrake to immobi-
lise the vehicle. Operating anomaly
W i t h t h e i g n i t i o n o n , t h e fl a s h i n g o f
"AUTO" and lighting of the service
warning light, accompanied by an
audible signal and a message on the
multifunction display, indicate a gear-
box malfunction.
Contact a PEUGEOT dealer without
delay.
If you press the accelerator
pedal beyond the point of
resistance, the gearbox
selects the gear below to
permit sharper acceleration. - switch on the ignition,
"AUTO"
and "-" appear on the instrument
panel display,
- press the brake pedal,
- wait approximately 30 seconds until "N" or a gear appears on
the instrument panel display,
- release the brake pedal.
The gearbox is operational again.
Automated mode
After using the sequential mode, you
can return to the automated mode by
selecting position
A .
"AUTO" and the gear engaged appear
on the instrument panel display.
The gearbox then operates in auto-
active mode, without any action on
the part of the driver.
It continuously selects the gear most
suited to the following parameters:
- driving style,
- road characteristics,
- vehicle load.
To optimise driving comfort and
obtain the most suitable gear, avoid
sharp variations in the pressure on
the accelerator pedal.
Page 113 of 194
7
106
Operating fault
If a speed limiter malfunction occurs,
t h e s p e e d i s r e p l a c e d b y fl a s h i n g
dashes. Contact a PEUGEOT dealer
to have the system checked.
Activating/deactivating the limiter
Switch the speed limiter on by
pressing button 4 .
Programming
Place the dial 1 in the LIMIT posi-
tion. The limiter is not yet active.
By default, the display indicates
the last speed programmed: Return to normal driving
Turn dial 1 to position "0" : the
speed limiter mode is deselected.
The display returns to the dis-
tance recorder.
In the event of a steep de-
scent or sharp acceleration,
the speed limiter will not be
able to prevent the vehicle
from exceeding the pro-
grammed speed.
In any event, the speed limiter cannot
replace the need to observe speed
limits, nor can it replace the need for
vigilance and responsibility on the
part of the driver.
The driver must remain alert and stay
in complete control of his vehicle.
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned correctly.
- n e v e r fi t o n e m a t o n t o p o f a n o t h e r .
Set the speed value by press-
ing button 2 or 3 ( e . g . : 7 0 m p h
( 1 1 0 k m / h ) ) .
You can then change the programmed
speed using buttons 2 and 3 :
- b y + o r - 1 m p h ( 1 k m / h ) = s h o r t press,
-
b y + o r - 5 m p h ( 5 k m / h ) = l o n g p r e s s ,
- i n s t e p s o f + o r - 5 m p h ( 5 k m / h ) = maintained press. Exceeding the programmed
speed
Pressing the accelerator pedal to
exceed the programmed speed will
not have any effect, unless you press
the pedal
fi r m l y passing the point of
resistance .
The speed limiter is deactivated tem-
porarily and the programmed speed,
w h i c h i s s t i l l d i s p l a y e d , fl a s h e s .
Returning to the programmed speed,
by means of intentional or uninten-
tional deceleration of the vehicle,
c a n c e l s t h e fl a s h i n g a u t o m a t i c a l l y
and reactivates the speed limiter.
Switch the speed limiter off by
pressing button 4 : the display
c o n fi r m s t h a t i t i s o f f ( O F F ) .
Switch the speed limiter back on
by pressing button 4 again.
Page 115 of 194
7
108
Exceeding the programmed speed
Intentional or unintentional exceeding
of the programmed speed results in
fl a s h i n g o f t h e p r o g r a m m e d s p e e d
on the display.
Returning to the programmed speed,
by means of intentional or uninten-
tional deceleration of the vehicle,
c a n c e l s t h e fl a s h i n g a u t o m a t i c a l l y .
Using the accelerator:
exceed the memorised speed until
the required speed is reached,
press button 2 or 3 .
Programming
Place switch 1 in the CRUISE
position. The cruise control is
not yet active and no speed has
been memorised. The display
indicates: Cancelling the cruise control
Switch the cruise control off by
pressing button 4 : the display
c o n fi r m s t h a t i t i s o f f ( O F F ) .
When changing the memo-
rised reference speed by
means of a maintained
press, pay attention as
the speed can increase or
decrease rapidly.
Do not use the cruise control on slip-
p e r y r o a d s o r i n h e a v y t r a f fi c .
In the event of a steep slope, the
cruise control cannot prevent the
vehicle from exceeding the pro-
grammed speed.
In any event, the cruise control can-
not replace the need to comply with
speed limits, nor can it replace the
need for vigilance and responsibility
on the part of the driver.
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned correctly.
- n e v e r fi t o n e m a t o n t o p o f a n o t h e r .
It is advisable to keep your feet near
the pedals.
Set the programmed speed by
accelerating to the required
speed, then press button 2 or 3
( e . g . : 7 0 m p h ( 1 1 0 k m / h ) ) .
Return to normal driving
Turn dial 1 to position "0" : the
cruise control mode is dese-
lected. The display returns to the
distance recorder. Operating fault
If a cruise control malfunction occurs,
t h e s p e e d i s r e p l a c e d b y fl a s h i n g
dashes. Contact a PEUGEOT dealer
to have the system checked.
You can then change the programmed
speed using buttons 2 and 3 :
- b y + o r - 1 m p h ( 1 k m / h ) = s h o r t press,
-
b y + o r - 5 m p h ( 5 k m / h ) = l o n g p r e s s ,
- i n s t e p s o f + o r - 5 m p h ( 5 k m / h ) = m a i n t a i n e d p r e s s . Reactivating the cruise control
Switch the cruise control back on
by pressing button 4 again.