service Peugeot 1007 Dag 2008.5 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2008.5, Model line: 1007 Dag, Model: Peugeot 1007 Dag 2008.5Pages: 194, PDF Size: 11.23 MB
Page 15 of 194
1
18
PETROL MANUAL GEARBOX AND "2 TRONIC" GEARBOX INSTRUMENT PANELS
1. Trip distance recorder zero
reset and total/trip distance
recorder display button.
2. Emission control system
warning light.
3. Service warning light.
4. Anti-lock braking system (ABS)
warning light.
5. Electronic stability control
(ESP/ASR) warning light.
6. H a n d b r a k e , b r a k e fl u i d l e v e l
and electronic brake force
distribution warning light.
7. Maximum coolant temperature
warning light.
8. Engine oil pressure warning
light.
9. Punctured wheel warning light.
10. Battery charge warning light.
11. Left direction indicator.
12. Fuel gauge.
13. Low fuel level warning light.
14. Central STOP warning light.
15. Speedometer.
16. Speed limiter/cruise control
indicator light.
17. Service indicator, engine oil
level gauge and total/trip
distance recorder.
18. "2 Tronic" gearbox indicator.
19. Foot on brake warning light
("2 Tronic" gearbox).
20. Rev counter.
21. Right direction indicator.
22. Dipped headlamps indicator
light.
23. Main beam headlamps indicator
light.
24. Front fog lamps indicator light.
25. Rear fog lamp indicator light.
26. Door open warning light.
27. Seat belt not fastened warning
light.
28. Passenger air bag disarmed
warning light.
29. Front, steering column, side and
curtain air bags warning light.
30. Lighting rheostat button.
Page 16 of 194
1
19
DIESEL MANUAL GEARBOX INSTRUMENT PANEL
1. Trip distance recorder zero
reset and total/trip distance
recorder display button.
2. Emission control system
warning light.
3. Service warning light.
4. Anti-lock braking system (ABS)
warning light.
5. Electronic stability control
(ESP/ASR) warning light.
6. H a n d b r a k e , b r a k e fl u i d l e v e l
and electronic brake force
distribution warning light.
7. Maximum coolant temperature
warning light.
8. Engine oil pressure warning
light.
9. Punctured wheel warning light.
10. Battery charge warning light.
11. Left direction indicator.
12. Fuel gauge.
13. Low fuel level warning light.
14. Central STOP warning light.
15. Speedometer.
16. Diesel engine pre-heat warning
light.
17. W a t e r i n d i e s e l fi l t e r w a r n i n g
light.
18. Speed limiter/cruise control
indicator light.
19. Service indicator, engine oil
level gauge and total/trip
distance recorder.
20. Rev counter.
21. Right direction indicator.
22. Dipped headlamps indicator
light.
23. Main beam headlamps indicator
light.
24. Front fog lamps indicator light.
25. Rear fog lamp indicator light.
26. Door open warning light.
27. Seat belt not fastened warning
light.
28. Passenger air bag disarmed
warning light.
29. Front, steering column, side and
curtain air bags warning light.
30. Lighting rheostat button.
Page 20 of 194
1
23
L a c k o f o i l
If "OIL" fl a s h e s a n d t h e s e r v i c e w a r n -
ing light comes on, accompanied by
an audible signal and a message on
the multifunction display, this indicates
a lack of oil which could damage the
engine.
I f t h e l a c k o f o i l i s c o n fi r m e d b y a
check using the dipstick, it is essential
that the level is topped up.
E n g i n e o i l l e v e l i n d i c a t o r
When the ignition is switched on, the
engine oil level is indicated for approxi-
mately 5 seconds after the service indi-
cator display.
O i l l e v e l g a u g e f a u l t
Check the oil level using the dipstick.
If "OIL --" fl a s h e s , t h i s i n d i c a t e s a
malfunction of the engine oil level
gauge.
Consult a PEUGEOT dealer.
INSTRUMENT PANEL DISPLAY
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator
- total distance recorder (total and trip distances).
The level read on the dipstick
will only be correct if the
vehicle is on level ground
and the engine has been off
for more than 15 minutes.
O i l l e v e l c o r r e c t
N o t e : the trip distance is displayed
for thirty seconds, when the ignition is
switched off, on opening and closing
the driver's door as well as on locking
the vehicle.
It also displays the "2 Tronic" gear-
box positions and operating modes
selected, as well as the information
relating to the cruise control or speed
limiter when one of these functions is
active.
Page 21 of 194
1
24
S e r v i c e i n d i c a t o r
This indicates when the next service
is due in accordance with the manu-
facturer's servicing schedule.
The point at which the next service
is due is calculated from the last indi-
cator zero reset. It is determined by
two parameters:
- the distance travelled,
- the time which has elapsed since the last service.
Operation
When the ignition is switched on, the
spanner symbolising the servicing
operations comes on; the distance
recorder display indicates the number
of miles [kilometres] (rounded off)
remaining until the next service.
E x a m p l e : 4,800 miles/km remain before
t h e n e x t s e r v i c e . F o r fi v e s e c o n d s a f t e r
the ignition is switched on, the display
indicates: 10 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total or trip
distance.
10 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and the
spanner remains lit.
It indicates that a service must be
carried out soon. The display indi-
cates the total or trip distance. T h e s e r v i c e i s o v e r d u e .
T h e s p a n n e r fl a s h e s f o r 5 s e c o n d s
each time the ignition is switched on.
10 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and the
spanner remains lit.
The display indicates the total or trip
distance.
The distance remaining before the
next service may be weighted by the
time factor, depending on the user's
driving habits.
The spanner may also come on if
more than two years have elapsed
since the last service.
T h e d i s t a n c e r e m a i n i n g t o
t h e n e x t s e r v i c e i s l e s s t h a n
5 0 0 m i l e s / 1 , 0 0 0 k m .
E x a m p l e : 400 miles/900 km remain
before the next service.
For 5 seconds after the ignition is
switched on, the display indicates:
E x a m p l e : the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
Page 22 of 194
1
25
S e r v i c e i n d i c a t o r z e r o r e - s e t
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
Switch off the ignition,
Press and hold the trip recorder
re-set button,
Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears. T o t a l / t r i p d i s t a n c e r e c o r d e r
B r i e fl y p r e s s i n g t h e b u t t o n a l t e r n a t e s
between the total and trip distance
displays.
To reset the trip distance recorder to
zero, when it is displayed press the
button until zeros appear.
L i g h t i n g r h e o s t a t
With the lights on, press the button to
vary the intensity of the lighting of the
instruments and controls. When the
lighting reaches the required bright-
ness, release the button.
After this operation, if you
wish to disconnect the bat-
tery, lock the vehicle and
w a i t f o r a t l e a s t fi v e m i n u t e s ,
otherwise the zero re-set will not be
registered.
Page 71 of 194
4
74
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by anyone
who does not have the key.
The ignition key has an electronic chip
which has a special code. When the
ignition is switched on, the code is
recognised and starting is possible.
If the system does not function
correctly, the service warning light
comes on, accompanied by an au-
dible signal and a message on the
multifunction display.
In this case, your vehicle will not
start. Contact a PEUGEOT dealer as
soon as possible.
Lost keys
Visit a PEUGEOT dealer with the ve-
h i c l e ' s V 5 r e g i s t r a t i o n c e r t i fi c a t e a n d
y o u r p e r s o n a l i d e n t i fi c a t i o n d o c u -
ments.
A PEUGEOT dealer will be able to
retrieve the key code and the tran-
sponder code required to order a
replacement key.
Programming the remote
control
Following changing of the remote
control battery or disconnection of
the vehicle battery, the remote con-
trol must be reprogrammed.
Wait at least one minute before
using the remote control.
Switch on the ignition.
Press button B or C for at least
fi v e s e c o n d s w i t h i n t h e n e x t t e n
seconds.
Switch off the ignition.
Wait at least one minute before
using the remote control.
The remote control is now working
again.
Changing the remote control
battery
Battery ref.: CR1620/3 volts.
T h e i n f o r m a t i o n " b a t t e r y fl a t " i s g i v e n
by displaying of the service warning
light, accompanied by an audible
signal and a message on the multi-
function display.
To replace the battery, unclip the casing
using a coin at the notch.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.
Page 73 of 194
4
74
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by anyone
who does not have the key.
The ignition key has an electronic chip
which has a special code. When the
ignition is switched on, the code is
recognised and starting is possible.
If the system does not function
correctly, the service warning light
comes on, accompanied by an au-
dible signal and a message on the
multifunction display.
In this case, your vehicle will not
start. Contact a PEUGEOT dealer as
soon as possible.
Lost keys
Visit a PEUGEOT dealer with the ve-
h i c l e ' s V 5 r e g i s t r a t i o n c e r t i fi c a t e a n d
y o u r p e r s o n a l i d e n t i fi c a t i o n d o c u -
ments.
A PEUGEOT dealer will be able to
retrieve the key code and the tran-
sponder code required to order a
replacement key.
Programming the remote
control
Following changing of the remote
control battery or disconnection of
the vehicle battery, the remote con-
trol must be reprogrammed.
Wait at least one minute before
using the remote control.
Switch on the ignition.
Press button B or C for at least
fi v e s e c o n d s w i t h i n t h e n e x t t e n
seconds.
Switch off the ignition.
Wait at least one minute before
using the remote control.
The remote control is now working
again.
Changing the remote control
battery
Battery ref.: CR1620/3 volts.
T h e i n f o r m a t i o n " b a t t e r y fl a t " i s g i v e n
by displaying of the service warning
light, accompanied by an audible
signal and a message on the multi-
function display.
To replace the battery, unclip the casing
using a coin at the notch.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.
Page 79 of 194
4
80
Automatic central locking
The doors can lock automatically
when you are driving (at a speed of
more than 6 mph (10 km/h).
You can activate or deactivate this
function. Driving with the doors locked
may make access to the pas-
senger compartment by the
emergency services more
d i f fi c u l t i n a n e m e r g e n c y .
Activation
With the ignition on, press and hold
button A .
Activation of the function is accompa-
nied by an audible signal and a mes-
sage on the multifunction display.
Deactivation
With the ignition on, press and hold
button A .
Deactivation of the function is
accompanied by an audible signal
and a message on the multifunction
display.
"Door open" alert -
when the vehicle is moving,
by lighting of the "door open"
warning light, accompanied by
an audible signal and a message
on the multifunction display for a
few seconds.
Opening/Closing using the
remote control
Press button C or D to open or close
the left or right door.
The opening and closing of the door is
accompanied by an audible signal.
2nd press on button C or D during
opening/closing interruption of the
movement.
3rd press on button C or D move-
ment of the door in the opposite
direction.
You are advised to use the
remote control or the controls
as much as possible.
Opening/Closing from the front
Press switch
B to open or close the
corresponding door.
Choosing the movement of the door
using the controls:
- pull opens the door,
- push closes,
- second press stops the
movement,
- the controls do not function above 3 mph (5 km/h).
If a door or the boot is not
closed properly, you are
warned:
- when the engine is running,
by lighting of the "door open"
warning light, accompanied by
a message on the multifunction
display for a few seconds.
Page 88 of 194
5
88
Daytime lights *
On vehicles which are equipped with daytime lights, the dipped headlamps come on when the vehicle is started.
A u t o m a t i c s w i t c h i n g o n o f
lights
The side lights and dipped beam headlamps switch on automatically if the light is poor and when the wind-screen wipers operate continuously. They switch off when the light be-comes bright enough or the wind-screen wipers are switched off.
I n f o g g y w e a t h e r o r i n s n o w , t h e b r i g h t n e s s s e n - s o r c a n d e t e c t s u f fi c i e n t l i g h t , t h e l i g h t s w i l l n o t come on automatically.
Do not cover the brightness s e n s o r , c o u p l e d w i t h t h e r a i n s e n s o r , l o c a t e d i n t h e c e n t r e o f t h e w i n d s c r e e n b e h i n d t h e i n t e r i o r mirror. It is used for automatic s w i t c h i n g o n o f t h e l i g h t s .
C o u p l i n g w i t h t h e F o l l o w M e
Home lighting
The association with the automatic lighting function provides the follow me home lighting with the following additional options:
- selection of maintaining of the lighting for a duration of 15, 30 or 60 seconds in the vehicle parameters of the multifunction d i s p l a y c o n fi g u r a t i o n m e n u (except in the case of the monochrome display A for which the duration is pre-set),
- automatic activation of the follow me home lighting when the automatic lighting function is in operation.
Activation
Turn the lighting control to the " AUTO " position.
Disarming
Turn the lighting control to a position other than " AUTO ".
Operating fault
If the brightness sensor does not function correctly, the lights come on accompanied by the service warning light, an audible signal and a message on the multifunction display.
Consult a PEUGEOT dealer.
Operating fault
If the brightness sensor does not function correctly, the lights come on accompanied by the service warning light, an audible signal and a messa-ge on the multifunction display.
Contact a PEUGEOT dealer.
Do not cover the brightness sensor, coupled with the rain sensor, located in the centre of the windscreen behind the interior mirror; the as-sociated functions would no longer be controlled.
This warning light comes on on the instrument panel.
The instruments and controls (ins-trument panel, multifunction display, air conditioning control panel, ...) are only lit on switching to the automa-tic switching on of the lights mode or when the lights are switched on ma-nually.
* According to country.
Page 89 of 194
5
88
Daytime lights *
On vehicles which are equipped with daytime lights, the dipped headlamps come on when the vehicle is started.
A u t o m a t i c s w i t c h i n g o n o f
lights
The side lights and dipped beam headlamps switch on automatically if the light is poor and when the wind-screen wipers operate continuously. They switch off when the light be-comes bright enough or the wind-screen wipers are switched off.
I n f o g g y w e a t h e r o r i n s n o w , t h e b r i g h t n e s s s e n - s o r c a n d e t e c t s u f fi c i e n t l i g h t , t h e l i g h t s w i l l n o t come on automatically.
Do not cover the brightness s e n s o r , c o u p l e d w i t h t h e r a i n s e n s o r , l o c a t e d i n t h e c e n t r e o f t h e w i n d s c r e e n b e h i n d t h e i n t e r i o r mirror. It is used for automatic s w i t c h i n g o n o f t h e l i g h t s .
C o u p l i n g w i t h t h e F o l l o w M e
Home lighting
The association with the automatic lighting function provides the follow me home lighting with the following additional options:
- selection of maintaining of the lighting for a duration of 15, 30 or 60 seconds in the vehicle parameters of the multifunction d i s p l a y c o n fi g u r a t i o n m e n u (except in the case of the monochrome display A for which the duration is pre-set),
- automatic activation of the follow me home lighting when the automatic lighting function is in operation.
Activation
Turn the lighting control to the " AUTO " position.
Disarming
Turn the lighting control to a position other than " AUTO ".
Operating fault
If the brightness sensor does not function correctly, the lights come on accompanied by the service warning light, an audible signal and a message on the multifunction display.
Consult a PEUGEOT dealer.
Operating fault
If the brightness sensor does not function correctly, the lights come on accompanied by the service warning light, an audible signal and a messa-ge on the multifunction display.
Contact a PEUGEOT dealer.
Do not cover the brightness sensor, coupled with the rain sensor, located in the centre of the windscreen behind the interior mirror; the as-sociated functions would no longer be controlled.
This warning light comes on on the instrument panel.
The instruments and controls (ins-trument panel, multifunction display, air conditioning control panel, ...) are only lit on switching to the automa-tic switching on of the lights mode or when the lights are switched on ma-nually.
* According to country.