ESP PEUGEOT 1007 DAG 2008 User Guide

5
91
COURTESY LIGHT

1. Front courtesy light

2. Map reading lights In the permanently on posi-
tion, there are different dura-
tions of lighting:
Boot light
The boot light is located in the left
boot trim.
It comes on automatically when the
boot is opened and switches of auto-
matically when the boot is closed.
Front courtesy light Permanently off.
Permanently on.
In this position, the courtesy
light comes on gradually:
- when the vehicle is unlocked,
- when the key is removed from the ignition,
- when the remote control locking button is pressed, in order to
locate your vehicle.
It switches off gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- 30 seconds after the last door is closed. Map reading lights
With the ignition on, press
the corresponding switch 2 .
- when the ignition is off, approxi-
mately ten minutes,
- in energy economy mode, ap- proximately thirty seconds,
- when the engine is running, no limit.

6
95
If this warning light comes on
on the instrument panel and
the indicator light on the but-
ton comes on, this indicates
that the ASR and ESP sys-
tems are disarmed.
TRACTION CONTROL (ASR) AND DYNAMIC STABILITY CONTROL (ESP)
Operation of the ASR and ESP
systems The warning light fl ashes if
the ASR or ESP is activated. Disarming
In exceptional conditions (starting a
vehicle which is bogged down, stuck
in snow, on soft ground, ...), it may
be advisable to disarm the ASR and
ESP systems, so that the wheels can
move freely and regain grip.

 Press the "ESP OFF" button,
located in the centre of the
fascia.
Reactivation These systems are reactivated auto-
matically each time the ignition is
switched back on or from 30 mph
(50 km/h).

 Press the "ESP OFF" button again
to reactivate them manually.
Operating fault
If this warning light comes on,
accompanied by an audible
signal and a message on the
multifunction display, this indi-
cates a malfunction of these
systems.
Have the systems checked by a
PEUGEOT dealer.
The ESP/ASR systems offer excep-
tional safety in normal driving, but
this should not encourage the driver
to take extra risks or drive at high
speed.
The correct functioning of these
systems depends on observation of
the manufacturer's recommenda-
tions regarding the wheels (tyres
and rims), the braking components,
the electronic components and the
PEUGEOT assembly and operation
procedures.
After an impact, have these systems
checked by a PEUGEOT dealer.
Activation of the ASR and ESP
systems
When the ignition is on, the ASR and
ESP systems are always active.
These systems are linked and com-
plement the ABS.
The ASR system optimises drive to
prevent the wheels skidding, by act-
ing on the brakes of the drive wheels
and on the engine. It also allows the
directional stability of the vehicle to
be improved on acceleration.
If there is a variation between the tra-
jectory followed by the vehicle and
that required by the driver, the ESP
system automatically acts on the
engine and the brake of one or more
wheels, in order to put the vehicle
back on course, within the limits of
the laws of physics.

6
97
Seat belt not fastened warning If the driver and/or the
front passenger has not
fastened his seat belt,
the corresponding warn-
ing light comes on when
the ignition is on, then, at a speed
above 12 mph (20 km/h), this is accom-
panied by an audible signal the volume
of which increases (for approximately
two minutes) and a message on the
multifunction display.

Note: a bag or an animal placed on
the front passenger seat may trigger
lighting of the warning light.
Seat belt unfastened warning
If the driver and/or one
of the passengers has
unfastened his seat
belt, the corresponding
warning light comes on
when the engine is running, then, at a
speed above 12 mph (20 km/h), this
is accompanied by an audible signal
the volume of which increases (for
approximately two minutes) and a
message on the multifunction display.
Rear seat belts
The rear seats are fi tted with two
three-point inertia reel seat belts.
The retaining of the rear seat belt
buckle by the sliding block makes
folding down or complete folding of
the seats easier.
Fastening

 Pull the strap, then insert the
buckle in the stalk.

 Check that the seat belt is
fastened correctly by pulling the
strap.
Unfastening

 Press the red button on the stalk.
Version with colour display
If the driver and/or one of the pas-
sengers has not fastened (or has
unfastened) his seat belt, a message
appears on the multifunction display.

7
106
Operating fault
If a speed limiter malfunction occurs,
the speed is replaced by fl ashing
dashes. Contact a PEUGEOT dealer
to have the system checked.
Activating/deactivating the limiter

 Switch the speed limiter on by
pressing button 4 .
Programming

 Place the dial 1 in the LIMIT posi-
tion. The limiter is not yet active.
By default, the display indicates
the last speed programmed: Return to normal driving

 Turn dial 1 to position "0" : the
speed limiter mode is deselected.
The display returns to the dis-
tance recorder.
In the event of a steep de-
scent or sharp acceleration,
the speed limiter will not be
able to prevent the vehicle
from exceeding the pro-
grammed speed.
In any event, the speed limiter cannot
replace the need to observe speed
limits, nor can it replace the need for
vigilance and responsibility on the
part of the driver.
The driver must remain alert and stay
in complete control of his vehicle.
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned correctly.
- never fi t one mat on top of another.

 Set the speed value by press-
ing button 2 or 3 (e.g.: 70 mph
(110 km/h)).
You can then change the programmed
speed using buttons 2 and 3 :
- by + or - 1 mph (1 km/h) = short press,
-
by + or - 5 mph (5 km/h) = long press,
- in steps of + or - 5 mph (5 km/h) = maintained press. Exceeding the programmed
speed
Pressing the accelerator pedal to
exceed the programmed speed will
not have any effect, unless you press
the pedal
fi rmly passing the point of
resistance .
The speed limiter is deactivated tem-
porarily and the programmed speed,
which is still displayed, fl ashes.
Returning to the programmed speed,
by means of intentional or uninten-
tional deceleration of the vehicle,
cancels the fl ashing automatically
and reactivates the speed limiter.

 Switch the speed limiter off by
pressing button 4 : the display
confi rms that it is off (OFF).

 Switch the speed limiter back on
by pressing button 4 again.

7
107
CRUISE CONTROL
This cruise control, of the new genera-
tion, is linked with the speed limiter. It
has a display on the instrument panel
to indicate the memorised reference
speed.
It enables the vehicle to maintain a
steady speed programmed by the
driver.
The cruise control is switched on
manually: it requires a minimum ve-
hicle speed of 25 mph (40 km/h) and
fourth gear must be engaged on the
manual gearbox.
The cruise control is switched off
by means of a manual action or by
pressing the brake or clutch pedal or
in the event of activation of the ESP.
By pressing the accelerator pedal, it is
possible to exceed the programmed
speed temporarily.
To return to the programmed speed,
simply release the accelerator pedal.
Switching off the ignition or turning
the dial cancels any programmed
speed value. Instrument panel display
The programmed information is
grouped together on the instrument
panel display.

5. Cruise control on/off indication

6. Cruise control mode selection in-
dication

7. Programmed speed value
Steering wheel controls
This system's controls are grouped
together on lever
A .

1. Cruise control mode selection dial

2. Value decrease button

3. Value increase button

4. Cruise control on/off button

7
108
Exceeding the programmed speed
Intentional or unintentional exceeding
of the programmed speed results in
fl ashing of the programmed speed
on the display.
Returning to the programmed speed,
by means of intentional or uninten-
tional deceleration of the vehicle,
cancels the fl ashing automatically.
Using the accelerator:

 exceed the memorised speed until
the required speed is reached,

 press button 2 or 3 .
Programming

 Place switch 1 in the CRUISE
position. The cruise control is
not yet active and no speed has
been memorised. The display
indicates: Cancelling the cruise control

 Switch the cruise control off by
pressing button 4 : the display
confi rms that it is off (OFF).
When changing the memo-
rised reference speed by
means of a maintained
press, pay attention as
the speed can increase or
decrease rapidly.
Do not use the cruise control on slip-
pery roads or in heavy traffi c.
In the event of a steep slope, the
cruise control cannot prevent the
vehicle from exceeding the pro-
grammed speed.
In any event, the cruise control can-
not replace the need to comply with
speed limits, nor can it replace the
need for vigilance and responsibility
on the part of the driver.
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned correctly.
- never fi t one mat on top of another.
It is advisable to keep your feet near
the pedals.

 Set the programmed speed by
accelerating to the required
speed, then press button 2 or 3
(e.g.: 70 mph (110 km/h)).
Return to normal driving

 Turn dial 1 to position "0" : the
cruise control mode is dese-
lected. The display returns to the
distance recorder. Operating fault
If a cruise control malfunction occurs,
the speed is replaced by fl ashing
dashes. Contact a PEUGEOT dealer
to have the system checked.
You can then change the programmed
speed using buttons 2 and 3 :
- by + or - 1 mph (1 km/h) = short press,
-
by + or - 5 mph (5 km/h) = long press,
- in steps of + or - 5 mph (5 km/h) = maintained press. Reactivating the cruise control

 Switch the cruise control back on
by pressing button 4 again.

7
109
VISUAL AND AUDIBLE REAR PARKING ASSISTANCE
This system consists of four proximity
sensors, located in the rear bumper,
and a special speaker.
This detects any obstacle (person,
vehicle, tree, gate, etc.) behind the
vehicle. Nevertheless, it cannot
detect obstacles located just below
the bumper.
An object, such as a stake, a road-
works cone or any other similar
object may be detected at the begin-
ning of the manoeuvre, but may no
longer be detected when the vehicle
comes close to it. Detection zone
Activation
The system is activated as soon as
reverse gear is engaged, accompa-
nied by an audible signal. The proxi-
mity information is given by:
- an audible signal, which beco-
mes more rapid as the vehicle
approaches the obstacle.
- a graphic on the multifunction display, with blocks which be-
come increasingly close to the
vehicle. When the distance between the rear
of the vehicle and the obstacle is less
than thirty centimetres, the audible
signal becomes continuous and the
"Danger" symbol appears on the
multifunction display.
On completion of the manoeuvre,
when you exit reverse gear, the sys-
tem becomes inactive.
The rear parking assistance sys-
tem cannot, in any circumstances,
take the place of the vigilance and
responsibility of the driver.

8
112

From outside: lift the catch A and
raise the bonnet. Bonnet strut
Secure the strut to hold the bonnet
open.
Before closing the bonnet, replace
the strut in its housing.
To close
Lower the bonnet and release it at
the end of its travel. Check that the
bonnet is properly locked.
OPENING THE BONNET

From inside: pull the handle on the
left-hand side under the fascia.
RUNNING OUT OF FUEL (DIESEL)
If your vehicle is fi tted with an HDI
engine, the fuel circuit must be rep-
rimed if you run out of fuel (refer to
the corresponding graphic).
This system consists of a repriming
pump and a transparent pipe.
1.4 litre Turbo HDI engine

 Open the bonnet.

 Fill the fuel tank with at least fi ve
litres of diesel.

 Squeeze and release the rep-
riming pump until fuel appears in
the transparent pipe.

 Operate the starter until the en-
gine starts.

 Close the bonnet.
1.6 litre Turbo HDI 16V engine

 Open the bonnet.

 Fill the fuel tank with at least
fi ve litres of diesel.

 Unclip the style cover to gain
access to the repriming pump.

 Squeeze and release the rep-
riming pump until fuel appears
in the transparent pipe with the
green connector.

 Operate the starter until the
engine starts.

 Put the style cover back in posi-
tion and clip it in place.

 Close the bonnet.
Opening the bonnet may
cause serious injuries,
please observe the following
recommendations:
- protect your hands and clothing,
- always allow the engine to cool before opening the bonnet,
- place the strut in its housing on the wing correctly,
- check that the bonnet is fi rmly secured in the open position,
- be aware of gusts of wind as they could cause the bonnet to
close suddenly.

8
116
CHECKS
Handbrake Where the handbrake travel
is too great or there is a re-
duction in the performance
of the system, the hand-
brake should be adjusted,
even between services.
Have the system checked by a PEUGEOT
dealer.
Air filter and passenger compartment filter
Particle emission filter (Diesel)
It is imperative that maintenance of
the particle emission fi lter is carried
out by a PEUGEOT dealer in accord-
ance with the manufacturer's servicing
schedule.
Brake pads
Brake pad wear depends
on the style of driving, in
particular for vehicles which
are used in town, over short
distances.
Brake disc/drum wear status
For any information relating to the
wear of the surfaces of the discs and
drums, contact a PEUGEOT dealer. Oil filter
Change the fi lter regularly, in
accordance with the servic-
ing schedule.
It may be necessary to
check the thickness of the
pads, even between services.
Unless there is a leak in the circuit, a drop in the brake fl uid level
indicates that the brake pads are
worn.
At the start of winter, have
your battery checked by a
PEUGEOT dealer.
Refer to the servicing book-
let for information on the
replacement interval for
these components.
Depending on the environ-
ment (dusty atmosphere...) and the
use of the vehicle (urban driving...),

change them twice as often, if ne
cessary (refer to the "Engines" para-
graph).
A clogged passenger compartment
fi lter may have an adverse effect on
the performance of the air condition-
ing system and produce unpleasant
odours.
Following prolonged opera-
tion of the vehicle at very
low speed or at idle, you
may, in exceptional circum-
stances, notice steam coming from
the exhaust during acceleration. This
has no effect on the performance of
the vehicle or on the environment.
Battery
Manual gearboxThis does not require an
oil change. Have the level
checked in accordance with
the manufacturer's servicing
schedule.
Only use products recom-
mended by PEUGEOT or
products of equivalent qual-
ity and characteristics.
To ensure best performance from
components as important as the
braking system, PEUGEOT selects
and offers quite specifi c products.
To prevent damage to the electri-
cal units, high pressure washing of
the engine compartment is strictly
prohibited .
To check the main levels
and certain components,
in accordance with the
manufacturer's servicing
schedule, refer to the pages of the
servicing booklet which correspond
to your vehicle's engine.

9
122
Rear lights

1. Brake/side lights
(P21 W/5 W).

2. Direction indicators (P21 W).

3. Reversing light (P21 W), right
side.
Fog lamp (P21 W), left side.
These 4 bulbs are changed by re-
moving the light:

 Remove the access fl ap in the
corresponding boot side trim to
access the light,

 Remove the two light fi xing nuts
inside the boot,

 Unclip the harness,

 Remove the light pressing on the
retaining tabs,

 Remove the seal,
 Remove the bulb holder moving
aside the two tabs A ,

 Turn the bulb a quarter of a turn,

 Remove the bulb and change it.

Note: if necessary, use the wheel-
brace to remove the nuts.
When refi tting, proceed in the re-
verse order and take care to position
the bulb holder, the seal and the light
correctly. Third brake light
(4 W 5 W bulbs)

 Using a 10 mm box spanner, un-
screw the 2 fi xing nuts A .

 Release the lamp unit by push-
ing it outwards.

 Disconnect the connector and
the rear wash-wipe pipe.

 Turn the bulb holder a quarter of
a turn and remove it.

 Remove the bulb and change it.
When refi tting, proceed in the re-
verse order and ensure that the lamp
unit seal and the rear wash-wipe pipe
have been put back in place correctly.
Do not tighten the nuts more than is
necessary at the risk of breaking the
light.
Number plate lights (W 5 W)

 Insert a thin screwdriver into one
of the external holes of the lens.

 Push it outwards to unclip it.

 Remove the lens.

 Remove the bulb and change it.