wheel PEUGEOT 106 DAG 2001 User Guide

P R A C T I C A L I N F O R M AT I O N8181
For your safety, always change a wheel:
Ð on level, solid, non-slippery ground,
Ð with the handbrake applied, Ð
with Þrst or reverse gear engaged,
Ð Chock the vehicle.
Ð Never position yourself under a vehicle which is supported only by a jack. Use a ramp.
After changing the wheel
Ð Have the wheel bolts and the tyre pressure checked as soon as possible.
Ð Have the damaged tyre repaired so that it can bereturned to the vehicle assoon as possible.
Ð The Òspace-savingÓ* type of spare wheel is Þtted with a
115/70R 15 tyre and is for
temporary use only.
- Pressure: 61 lbf. in 2
(4.2 bars).
- Maximum speed: 50 m.p.h. (80 km/h).
* According to speciÞcation
3
Special procedure for Sport model Positioning the jack
Ð Close the jack completely.
Ð Position the jack under the vehicle at the jacking points tilting it by 90¡, so that the jack handle hinge is at the same height as the sill trim, then straighten it.
Ð Check that the jack is in correct contact with the sill. Replacing the wheel in the carrier
Ð Position the jack storage box with the arrow pointing forwards.
Never place the jack in contact with the sill trim.
06-05-2002

Special features of the alloy wheels* Bolt covers Alloy wheel bolts are covered by chrome trims. Use tool 3to remove the trims before
slackening the bolts. Anti-theft bolt** If your wheels are Þtted with an anti- theft bolt (one per wheel), thechrome trim and then the plasticcover must be removed, using tool
3,
before it is unscrewed using one ofthe two anti-theft sockets (whichwere given to you on delivery of yourvehicle along with the duplicate keysand the conÞdential card) and thewheel brace 1.
Note: make a careful note of the code
number engraved on the top of theanti-theft socket. This will enable youto obtain a duplicate of the anti-theft
socket from a PEUGEOT dealer.
* According to speciÞcation.
** According to model and destination.
Fitting the spare wheel If your vehicle is Þtted with a steel spare wheel, it is normal when secu-ring it to notice that the bolt washersdo not come into contact with therim. The spare wheel is secured bythe cone-shaped support of eachbolt. Fitting snow tyres If you Þt snow tyres mounted on steel wheels, it is
essentialto use special
bolts available from your PEUGEOT
dealer.
P R A C T I C A L I N F O R M AT I O N82
33
06-05-2002

Direction indicator bulbs PY21W Access to the bulbs is from inside the wheel arch.
Turn the wheels to full lock (to the left to change the right hand bulband vice versa). Open the access ßap.
Turn the socket 1/4 turn.Change the bulb. Ensure that the ßap is closed
correctly.Side repeater W5W* Pull the rear part of the transparent
cover and detach the assembly. Support the connector and turn the transparent cover 1/4 turn. Change the bulb.
Rear lights Direction indicators
PY21W
Reversing lights P21W
Fog lamp P21W
Tail lights P5W
Brake/tail lights P21/5W
From inside the luggage com- partment: Remove the plastic protector 1.
Remove the air outlet grille 2using
a cross-head screwdriver. Slacken the two wing nuts 3and
release the light block 4.
Pinch the lugs 5to remove the
bulb-holder. Change the bulbs. * According to speciÞcation
P R A C T I C A L I N F O R M AT I O N84
4
3
1
2
5
06-05-2002

Direction indicator bulbs PY21W Access to the bulbs is from inside the wheel arch.
Turn the wheels to full lock (to the left to change the right hand bulband vice versa). Open the access ßap.
Turn the socket 1/4 turn.Change the bulb. Ensure that the ßap is closed
correctly.Side repeater W5W* Pull the rear part of the transparent
cover and detach the assembly. Support the connector and turn the transparent cover 1/4 turn. Change the bulb.
Rear lights Direction indicators
PY21W
Reversing lights P21W
Fog lamp P21W
Tail lights P5W
Brake/tail lights P21/5W
From inside the luggage com- partment: Remove the plastic protector 1.
Remove the air outlet grille 2using
a cross-head screwdriver. Slacken the two wing nuts 3and
release the light block 4.
Pinch the lugs 5to remove the
bulb-holder. Change the bulbs. * According to speciÞcation
P R A C T I C A L I N F O R M AT I O N84
4
3
1
2
5
06-05-2002

T E C H N I C A L D ATA102
For your PEUGEOT, only use accessories and original parts approved by the manufacturer.
These accessories and parts are all suitable for your PEUGEOT, after being tested and approved for reliability and
safety.
A wide choice of original accessories, approved by PEUGEOT, is available through the network.They all carry the PEUGEOT guarantee. Security:Anti-theft alarms, engraving of windows, wheel anti-theft devices, fog lamps...
Comfort: Air conditioning, telephone console, seat covers, carpets, luggage compartment tray, mud ßaps, sun roof*, luggage net, armrest, door deßectors, storage under the rear parcel shelf...
Communication: Audio equipment, telephone, CB, loud speakers, CD changer, navigation...
Personalisation: Tailgate spoiler, alloy wheels, Þnishers, steering wheels, sport exhaust...
Leisure: Towbar, roof bars, roof box, carriers (for bicycles, skis...)
Children: Booster seats and child seats, side blinds and rear blind...
Maintenance products: Windscreen wiper ßuid, internal and external cleaning and maintenance products...
* As the Þtting of a sun roof may involve cutting the roof strengthener, it is imperative that only original PEUGEOTproducts are used.
06-05-2002

T E C H N I C A L D ATA100
3
4
5
6A
CD
1 2
B
A. ManufacturerÕs plate 1 : EU legislation*
2 : Serial number
3 : Maximum gross vehicle weight (GVW)
4 : Maximum gross train weight (GTW)
5 : Maximum front axle load
6 : Maximum rear axle load
B. Serial number on body C. Legislation plate* D. Tyres and paint reference The label
DafÞxed to the edge of the driverÕs door indicates:
- the dimensions of the wheel rims and tyres,
- the brands of tyres approved by the manufacturer,
- the tyre inßation pressures (the inßation pressure must be
checked when cold, at least once a month) ,
- the paint colour reference. * According to speciÞcation
IdentiÞcation
06-05-2002