bulb Peugeot 206 Dag 2003 Owner's Manual

YOUR 206 AT A GLANCE1
Each model may only be fitted with some of the equipment shown, according to its specification and the technical requirements in the country of first registration of the vehicle.
206 SW: version available according to country. Pages
Seats 74 - 85
Instruments and controls 29 - 31
Control panel 37 - 73, 97 - 98
Mirrors 100
Pages
Checks 117 - 125
Access 87 - 92
Changing a wheel 126 - 130
Changing a bulb 131 - 135
26-05-2003

26-05-2003
PRACTICAL INFORMATION131
Dipped/main headlamps H7 55 W
Ð Pull the tab Aupwards and remove the protective cover.
Ð Disconnect the connector.
Ð Press the end of the securing clip to remove it. Change the faulty bulb.
Ð On fitting, ensure that the direction notches are in the correct position and that the clip is secured correctly.
Ð Reconnect the connector.
Ð Replace the protective cover. Side lights W 5 W
Turn the pin connector
Ba quarter turn and remove it.
Change the bulb.
Remarks
Ð Only touch the bulbs with a dry cloth.
Ð To replace the bulbs on the right side, remove the wash-wipe reservoir filler pipe first.
Ð Condensation may form inside the headlamps. It will disappear when the lights are used.
CHANGING A BULB

26-05-2003
PRACTICAL INFORMATION
132
Amber direction indicator
side repeater WY 5 W Push the repeater forwards or back-
wards and release the assembly. Hold the connector and turn the transparent cover a quarter turn. Change the bulb.
Amber direction indicators
PY 21 W
Turn the pin connector Ca quarter
turn and remove it. Change the bulb.
PEUGEOT recommends the use of H7 bulbs ofbrands:
Ð GE/TUNGSRAM,
Ð PHILIPS,
Ð OSRAM,
to avoid damaging the headlamps. These comply with the anti-UV (ultraviolet) specifications neces-sary for the correct operation andreliability of the headlamps. The headlamps are fitted with polycarbon glass with a protective
coating. We strongly adviseagainst cleaning them using a dryor abrasive cloth or using deter-gents or solvents. Use a soft, damp cloth.

26-05-2003
PRACTICAL INFORMATION
134
Front fog lamps H1 55 W Press under the access flap to release it. Open the flap.
Turn the cover to remove it.Disconnect the bulb.Press the two ends of the securing clip to release the bulb.
Third brake light 5 bulbs
W 5 W (saloon, 206 RC)
Using a 10 mm spanner, unscrew the 2 nuts A.
Release the light unit. Squeeze the two tabs Bto release
the bulb holder.Change the faulty bulb. Third brake light (206 SW) This is fitted with electroluminescent diodes. In the event of a fault, consult a
PEUGEOT dealer.

26-05-2003
PRACTICAL INFORMATION133
Rear lights (saloon, 206 RC) Unclip the boot side trim.Remove the wing bolt.Release the light unit.Press the lug
Aand disconnect the
connector.Remove the foam.Move aside the tabs Band remove
the bulb holder.Change the faulty bulb.When refitting, ensure that the bulb holder and the light are repositioned
correctly.
Saloon, 206 RC 206 SW
1. Direction indicators P 21 W.
2. Reversing lights P 21 W.
3. Brake lights/side lights P 21/5 W.Rear lights (206 SW) Unclip the top of the boot trim using a coin. Unscrew the two wing bolts using
the wheelbrace if necessary. Release the light unit.
Disconnect the connector. Move aside the tabs 1and remove the
bulb holder 2.
Change the faulty bulb. When refitting, refit the boot trim by engaging it from the bottom thenclipping the top.

26-05-2003
PRACTICAL INFORMATION
134
Front fog lamps H1 55 W Press under the access flap to release it. Open the flap.
Turn the cover to remove it.Disconnect the bulb.Press the two ends of the securing clip to release the bulb.
Third brake light 5 bulbs
W 5 W (saloon, 206 RC)
Using a 10 mm spanner, unscrew the 2 nuts A.
Release the light unit. Squeeze the two tabs Bto release
the bulb holder.Change the faulty bulb. Third brake light (206 SW) This is fitted with electroluminescent diodes. In the event of a fault, consult a
PEUGEOT dealer.

26-05-2003
PRACTICAL INFORMATION135
Rear fog lamp P 21 W Unclip the lamp and release the
assembly.
Turn the pin connector a quarter turn and remove it. Change the bulb. Number plate lights W 5 W Insert a thin screwdriver into one of the outer holes of the transparent
cover. Push it outwards to unclip it.
Remove the transparent cover.Change the faulty bulb.