ignition Peugeot 206 P Dag 2009 Owner's Manual

FAMILIARISATION EXTERIOR
Automatic switching on of the lights
This equipment switches on the side
lights and dipped headlamps when the
light is poor or when the windscreen
wipers are operating continuously,
when the lights stalk is in the "AUTO"
position.

 49
"Follow me home" lighting
This function, linked with the automatic
switching on of the lights or activated
manually, allows you to leave the front
lights on after switching off the ignition.

 48 Braking assistance systems
(ABS, EBFD and EBA)
These systems are linked and comple-
ment each other to assist you to brake
safely and effectively in emergency
situations.

 53

FAMILIARISATION
MONITOR THOROUGHLY

1. When the ignition is on, the orange
and red warning lights come on.

2. When the engine is running, these
warning lights should switch off.
If warning lights remain on, refer to the
page concerned.
Warning lights

 16
Instrument panel

A. When the ignition is on, the fuel
gauge needle should rise.

B. When the engine is running, the
associated low level warning light
should switch off.
If the levels are not correct, top up as
required.

 15 Controls

A. Passenger air bag disarming.

 58

B. Heated seats control.

 33

C. Deactivation of the ESP/ASR.

 54

D. Central locking/unlocking.

 44

FAMILIARISATION DRIVE SAFELY

1. Stop position.

2. Accessories position.

3. Ignition position.

4. Starting position.
Start

 40 Cruise control "CRUISE"

1. Cruise control mode Selection/Off.

2. Decreasing of the programmed value.

3. Increasing of the programmed value.

4. Cruise control Off/Resume.

1. Speed limiter mode Selection/Off.

2. Decreasing of the programmed value.

3. Increasing of the programmed value.

4. Speed limiter On/Off.
Speed limiter "LIMIT"

 64

 66
Adjustments must be made with the en-
gine running.
In order to be programmed or activated,
the vehicle speed must be higher than
25 mph (40 km/h), with at least fourth
gear engaged on the manual gearbox.

15
PETROL - DIESEL MANUAL GEARBOX INSTRUMENT PANELS
Panel which groups together the vehicle operation dials and indicator lights.

4. Speedometer.
Indicates the current speed of the moving vehicle (km/h).

5. Display.

6. Display zero reset button.
Resets the selected function to zero (trip distance recorder or service
indicator).

7. Instrument panel lighting button.
Adjusts the brightness of the lighting of the instrument panel.
Dials

1. Rev counter.
Indicates the speed of rotation of the engine (x 1 000 rpm).

2. Fuel gauge.
Indicates the quantity of fuel remaining in the tank.

3. Cooling temperature.
Indicates the temperature of the engine coolant (°Celsius).
A. Cruise control.
Speed limiter.
(km/h)

B. Trip distance recorder.
(km)

C. Service indicator.
(km) then,
Distance recorder.
(km)
These three functions are displayed in succession when the ignition is
switched on.
For further information, refer to the sec-
tion which corresponds to the function
and to the display associated with it.
Display

!
16
The indicator/warning light comes
on continuously or fl ashes.
Some indicator/warning lights may
light in two different ways. Only by
relating the type of lighting to the
vehicle operating status can it be
ascertained whether the situation
is normal or whether a fault has oc-
curred.
Indicator and warning lights
Visual indicators which inform the driver
when a system comes into operation
(operation or deactivation indicator
lights) or of the occurrence of a fault
(warning light).
Associated warnings
The lighting of certain indicator/warning
lights may be accompanied by an audible
signal and a message on the multifunc-
tion display. Operation indicator lights
The lighting of one of the following indi-
cator lights confi rms that the correspond-
ing system has come into operation.

Left-hand direction indicator.

Handbrake applied.

Right-hand direction indicator.

Main beam headlamps.

Dipped headlamps.

Diesel engine pre-heating.
Wait until this switches off
before operating the starter.
Front fog lamps.

Rear fog lamps.
When the ignition is switched on
The warning lights come on for a few
seconds when the vehicle ignition is
switched on.
When the engine is started, these warn-
ing lights should switch off.
If they remain on, before moving off,
consult the text relating to the warning
light concerned.

18
Engine autodiagnostics system.
The lighting of this warning light
indicates the occurrence of a
fault in the engine management
system.
Flashing of this warning light indicates
the occurrence of a fault in the emission
control system.
Engine oil pressure.
The lighting of this warning light
indicates the occurrence of a
fault in the engine lubrication
circuit. It is imperative that the vehicle is
stopped as soon as it is safe to do so. Battery charge.
The lighting of this warning light
indicates the occurrence of a
fault in the battery charging cir-
cuit (dirty or loose terminals, slack or
cut alternator belt, ...).
Braking.
The lighting of this warning light
indicates the occurrence of a fault
in one of the braking systems:
- signifi cant drop in the level in the circuit,
- electronic brake force distribution (EBFD) faulty (if lit at the same time
as the ABS warning light).
It is imperative that the vehicle is stopped as soon as it is safe to do so.
If the vehicle is moving, check that the
handbrake has been released fully.
Low fuel level.
The lighting of this warning light
indicates that there is enough
fuel left to drive approximately
30 miles (50 km).
The capacity of the fuel tank is approxi-
mately 50 litres. Maximum coolant
temperature.
The lighting of this warning light
indicates an excessively high
temperature in the cooling system. It is
imperative that the vehicle is stopped
as soon as it is safe to do so.
Door open.
A door, the boot or the bonnet
is still open:
Seat belt not fastened/
unfastened. The lighting of this warning light
indicates that the driver has not
fastened his seat belt or has
unfastened it.
- if the speed is below 6 mph (10 km/h),
this warning light comes on continu-
ously,
-
if the speed is above 6 mph (10 km/h),
this warning light comes on continuously,
accompanied by an audible signal.

Dynamic stability control
(ESP/ASR).
This warning light comes on for
a few seconds each time the
ignition is switched on.
When the engine is running and the
vehicle is moving, it comes on if the sys-
tem is activated.
It comes on continuously accompanied
by a message on the multifunction dis-
play when the system is deactivated.
If the warning light remains on when
the engine is running and the vehicle is
moving, contact a PEUGEOT dealer.

20
Maintenance indicator
System which informs the driver when
the next service is due, in accord-
ance with the manufacturer's servicing
schedule.
The point at which the service is due is
calculated from the last indicator zero
reset. It is determined by two parameters:
- the distance travelled,
- the time elapsed since the last service. More than 620 miles (1 000 km)
remain before the next service is due
For 5 seconds after the ignition is
switched on, the spanner symbolising
the service operations comes on. The
distance recorder display line indicates
the distance remaining before the next
service is due.

Example: 4 800 miles/km remain be-
fore the next service is due.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the spanner is switched off ; the
distance recorder resumes its normal
operation. The display then indicates
the total and trip distances. Less than 620 miles (1 000 km)
remain before the next service is due

Example: 560 miles (900 km) remain
before the next service is due.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the distance recorder resumes
its normal operation. The spanner
remains on to indicate that a service
must be carried out soon.

ii
ii
21
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into
account.
Maintenance indicator zero reset
After each service, the maintenance
indicator must be reset to zero.
The procedure for resetting to zero is as
follows:

 switch off the ignition,

 press and hold the trip distance
recorder zero reset button,

 switch on the ignition; the distance
recorder display begins a count-
down,

 when the display indicates "=0" ,
release the button; the spanner dis-
appears.
The distance remaining may be
weighted by the time factor, depend-
ing on the driver's driving habits.
Therefore, the spanner may also
come on if you have exceeded the
two year service interval.
Service overdue
For 5 seconds after the ignition is
switched on,
the spanner fl ashes to
indicate that the service must be carried
out as soon as possible.

Example: the service is overdue by
300 miles/km.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the distance recorder resumes
its normal operation. The spanner
remains lit .

22
Total distance recorder
System which measures the total dis-
tance travelled by the vehicle during its
life. Lighting rheostat
System for manual adjustment of the
brightness of the instrument panel in
relation to the exterior brightness.
The total and trip distances are displayed for thirty seconds when the ignition is
switched off, when the driver's door is
opened and when the vehicle is locked
or unlocked.
Trip distance recorder
System which measures a distance
travelled during a day or other period
since it was reset to zero by the driver.

 With the ignition on, press the button
until zeros appear. Activation
When the lights are on:

 press the button to change the
brightness of the instrument panel,

 when the lighting reaches the mini-
mum setting, release the button,
then press again to increase it,
or

 when the lighting reaches the maxi-
mum setting, release the button,
then press again to reduce it,

 when the lighting reaches the level
of brightness required, release the
button.
Deactivation
When the lights are off, pressing the
button does not have any effect.

25
Display B
TRIP COMPUTER
Zero reset
Press the stalk for more than two seconds.
Range
This shows the distance that can still be
covered with the fuel remaining in the
tank.

Note: this fi gure may increase if there
is a change in the style of driving or the
road surface, producing a signifi cant
drop in current consumption.
When the range is less than 20 miles
(30 km), three segments are dis-
played. After fi lling with fuel, the range
is displayed when it exceeds 60 miles
(100 km).
If horizontal segments are displayed for
long periods instead of digits, contact a
PEUGEOT dealer.
Pressing the button on the end of the

wash/wipe stalk enables the following
data to be displayed:
- the range
- the distance travelled
- the average consumption
- the current consumption
- the average speed Average consumption
This is the average fuel consumption
since the computer was last set to zero.
Current consumption
This is the average quantity of fuel con-
sumed during the last few seconds.
This function is displayed only when the
vehicle is travelling at a speed greater
than 20 mph (30 km/h). Distance travelled
This indicates the distance travelled
since the computer was last set to
zero.
Average speed
This is the average speed calculated
since the computer was last set to zero
(with the ignition on).