key Peugeot 206 P Dag 2010 User Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2010, Model line: 206 P Dag, Model: Peugeot 206 P Dag 2010Pages: 107, PDF Size: 3.94 MB
Page 43 of 107
50
FUEL TANK
R e s e r v o i r w h i c h s h o u l d b e r e fi l l e d w i t h
fuel, when the minimum level has been
detected.
Fuel tank capacity: approximately
50 litres. Filling
A l a b e l a f fi x e d t o t h e i n s i d e o f t h e t a n k
reminds you of the type of fuel to be
used depending on your engine.
More than 5 litres of fuel must be add-
ed in order to be registered by the fuel
gauge.
The key cannot be removed from the
l o c k u n t i l t h e fi l l e r c a p i s r e fi t t e d .
Opening the cap may release a vacu-
um, indicated by a noise. This is caused
by the sealing of the fuel system.
T o fi l l t h e t a n k s a f e l y :
the engine
must be
switched off,
i n s e r t t h e k e y i n t h e fi l l e r c a p , t h e n
turn it to the left,
r e m o v e t h e fi l l e r c a p ,
fi l l t h e t a n k , but do not continue
after the 3rd cut-off of the pump ;
this could cause malfunctions.
W h e n y o u h a v e fi l l e d t h e t a n k :
r e fi t t h e fi l l e r c a p ,
turn the key to the right, then remove
i t f r o m t h e fi l l e r c a p .
Page 46 of 107
!
i
i
53
"Guide me home" lighting
When you leave your vehicle, the side-
lamps and dipped beam headlamps can
be left on for approximately 30 seconds.
To do this:
- place the key in the STOP position,
- place the lighting stalk in the 0 posi-
tion,
- fl a s h t h e h e a d l a m p s ,
- get out of the vehicle and lock it. D i r e c t i o n i n d i c a t o r s ( fl a s h e r s )
Left: downwards.
Right: upwards.
In good or rainy weather, both
day and night, the front foglamps
and the rear foglamp cause daz-
zle and their use is prohibited.
Do not forget to switch them off
when they are no longer needed.
V e h i c l e s fi t t e d w i t h f r o n t
foglamps and a rear foglamp
(ring C)
When the lighting is switched off
automatically or when the dipped
beam headlamps are switched
off manually, the front foglamps,
the rear foglamp and the side-
lamps remain on (turn the ring
backwards to switch off the front
foglamps. The sidelamps then
switch off).
F r o n t f o g l a m p s ( fi r s t r o t a t i o n o f t h e r i n g
forwards).
To switch off the rear foglamp and
the front foglamps, turn the ring
backwards twice in succession.
The front foglamps operate with the
sidelamps, the dipped beam headlam-
ps and the main beam headlamps.
Front and rear foglamps (2nd rotation of
the ring forwards).
Page 47 of 107
54
AUTOMATIC ILLUMINATION OF
HEADLAMPS
The sidelamps and dipped beam head-
lamps switch on automatically if the light
is poor and when the windscreen wip-
ers operate continuously and switch off
when the light becomes bright enough
or the windscreen wipers are switched
off.
I n f o g g y w e a t h e r o r i n s n o w , t h e
b r i g h t n e s s s e n s o r m a y d e t e c t s u f fi -
c i e n t l i g h t , t h e l i g h t i n g w i l l n o t c o m e
o n a u t o m a t i c a l l y . I f n e c e s s a r y , t h e
dipped beam headlamps must be
s w i t c h e d o n m a n u a l l y .
This function is active when the vehicle
is supplied to the customer.
To deactivate or activate the function:
- Place the key in the accessories po-sition (1st notch),
- Place the lighting stalk in the 0 posi-
tion,
- Press the end of the lighting stalk for more than four seconds.
D o n o t c o v e r t h e b r i g h t n e s s s e n s o r ,
c o u p l e d w i t h t h e r a i n s e n s o r , l o c a t e d
i n t h e c e n t r e o f t h e w i n d s c r e e n , b e -
hind the
r e a r v i e w
mirror. It is used
for
the
automatic
illumination
of
headlamps
. Operating check
Activation
Activation is accompanied by an audible
signal and a message on the multifunc-
tion screen.
Deactivation
Deactivation is accompanied by an au-
dible signal.
When the driver uses the manual light-
ing controls, the function is temporarily
deactivated.
If the brightness sensor does not
function correctly , the lighting come
on accompanied by an audible signal
and a message on the multifunction
screen.
Consult a PEUGEOT dealer.
HEADLAMP ADJUSTMENT
Depending on the load in your vehicle,
it is recommended that the headlamp
beam is adjusted.
0. 1 or 2 people in the front seats.
- . 3 people.
1. 5 people.
2. 5 people + maximum authorised
load.
3. Driver + maximum authorised load.
Initial setting is position 0.
Page 49 of 107
i
56
A u t o m a t i c r a i n s e n s i t i v e w i n d s c r e e n
w i p e r s
In the AUTO position, the windscreen
wipers operate automatically and adapt
their speed to the intensity of the
rainfall .
Operating check
Activation
Activation of the function is accompa-
nied by a message on the multi-function
screen.
In the event of malfunction , the driver
is informed by an audible signal.
In the AUTO position, the windscreen
wiper will operate in intermittent mode.
Contact a PEUGEOT dealer to have the
system checked.
Do not cover the rain sensor located
on the windscreen behind the rear view
mirror.
When using an automatic car wash,
switch off the ignition or check that the
wiper stalk is not in the AUTO position.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic rain
sensitive wipers.
W i n d s c r e e n w a s h
Pull the wiper stalk towards you. The
windscreen wash, then the windscreen
w i p e r s , o p e r a t e f o r a s p e c i fi e d t i m e .
R e a r s c r e e n w i p e r
Turn ring A t o t h e fi r s t n o t c h f o r i n t e r m i t -
tent wiping.
I f t h e i g n i t i o n i s s w i t c h e d o f f , i t i s
necessary to reactivate the control
each time . To do this, move the stalk
to any position, then move it back to the
required position.
A u t o m a t i c r e a r s c r e e n w i p e r
When the windscreen wipers control is
activated and you engage reverse gear,
the rear screen wiper operates intermit-
tently.
R e a r s c r e e n w a s h
Turn ring A p a s t t h e fi r s t n o t c h ; t h e
screen wash then the wiper operate for
a fi x e d p e r i o d . If you use a bicycle carrier, con-
sult a PEUGEOT dealer to have
this function deactivated or install
a s p e c i fi c b i c y c l e c a r r i e r a p p r o v e d
by PEUGEOT. COURTESY LAMPS
System for selecting and controlling
the various passenger compartment
lamps.
Front courtesy lamp (button A)
- when the vehicle is unlocked,
- when a door is opened,
- when the ignition is switched off.
It switches off when the vehicle is
locked.
I t fl a s h e s w h i l e d r i v i n g i f a d o o r i s n o t
closed correctly.
Permanently off.
Permanently on, when the key
is in the accessories position or
with the ignition on.
In this position, the courtesy
lamp comes on for approxi-
mately 30 seconds:
Page 50 of 107
i
56
A u t o m a t i c r a i n s e n s i t i v e w i n d s c r e e n
w i p e r s
In the AUTO position, the windscreen
wipers operate automatically and adapt
their speed to the intensity of the
rainfall .
Operating check
Activation
Activation of the function is accompa-
nied by a message on the multi-function
screen.
In the event of malfunction , the driver
is informed by an audible signal.
In the AUTO position, the windscreen
wiper will operate in intermittent mode.
Contact a PEUGEOT dealer to have the
system checked.
Do not cover the rain sensor located
on the windscreen behind the rear view
mirror.
When using an automatic car wash,
switch off the ignition or check that the
wiper stalk is not in the AUTO position.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic rain
sensitive wipers.
W i n d s c r e e n w a s h
Pull the wiper stalk towards you. The
windscreen wash, then the windscreen
w i p e r s , o p e r a t e f o r a s p e c i fi e d t i m e .
R e a r s c r e e n w i p e r
Turn ring A t o t h e fi r s t n o t c h f o r i n t e r m i t -
tent wiping.
I f t h e i g n i t i o n i s s w i t c h e d o f f , i t i s
necessary to reactivate the control
each time . To do this, move the stalk
to any position, then move it back to the
required position.
A u t o m a t i c r e a r s c r e e n w i p e r
When the windscreen wipers control is
activated and you engage reverse gear,
the rear screen wiper operates intermit-
tently.
R e a r s c r e e n w a s h
Turn ring A p a s t t h e fi r s t n o t c h ; t h e
screen wash then the wiper operate for
a fi x e d p e r i o d . If you use a bicycle carrier, con-
sult a PEUGEOT dealer to have
this function deactivated or install
a s p e c i fi c b i c y c l e c a r r i e r a p p r o v e d
by PEUGEOT. COURTESY LAMPS
System for selecting and controlling
the various passenger compartment
lamps.
Front courtesy lamp (button A)
- when the vehicle is unlocked,
- when a door is opened,
- when the ignition is switched off.
It switches off when the vehicle is
locked.
I t fl a s h e s w h i l e d r i v i n g i f a d o o r i s n o t
closed correctly.
Permanently off.
Permanently on, when the key
is in the accessories position or
with the ignition on.
In this position, the courtesy
lamp comes on for approxi-
mately 30 seconds:
Page 57 of 107
63
Operating fault Lateral airbags Triggering
The lateral airbags are triggered unilater-
ally in the event of a serious side impact
applied to all or part of the lateral impact
zone
B , perpendicular to the longitudinal
centreline of the vehicle on a horizontal
plane and directed from the outside to-
wards the inside of the vehicle.
T h e l a t e r a l a i r b a g i n fl a t e s b e t w e e n t h e
occupant of the vehicle and the corre-
sponding door trim panel.
Impact detection zones
A. Front impact zone.
B. Side impact zone.
Deactivating the front
passenger's front airbag
To ensure the safety of your child, it is
essential to deactivate the passenger's
airbag when you install a rear-facing
child seat on the front passenger seat.
Otherwise, the child would risk being
seriously injured or killed if the airbag
w e r e t o i n fl a t e .
With the ignition switched off , insert
the key into the passenger's airbag de-
activation switch, turn it to the "OFF"
position, then remove the key keeping
the switch in the new position. Reactivation
As soon as the child seat is removed,
turn the airbag switch to the
"ON" po-
sition to reactivate the airbag and thus
ensure its safety function.
System which protects the driver in the
event of a serious side impact in order
to limit the risk of injury to the chest.
T h e l a t e r a l a i r b a g i s fi t t e d i n t h e s e a t
back frame, on the door side. When the ignition is on, this
warning lamp remains lit on the
instrument panel if the passen-
ger's airbag is deactivated.
If this warning lamp comes on,
accompanied by an audible
signal and a message on the
multifunction screen, contact a
PEUGEOT dealer to have the airbag
system checked. In the
"OFF" position, the passenger's
airbag will not be triggered in the event
of an impact.
Page 59 of 107
63
Operating fault Lateral airbags Triggering
The lateral airbags are triggered unilater-
ally in the event of a serious side impact
applied to all or part of the lateral impact
zone
B , perpendicular to the longitudinal
centreline of the vehicle on a horizontal
plane and directed from the outside to-
wards the inside of the vehicle.
T h e l a t e r a l a i r b a g i n fl a t e s b e t w e e n t h e
occupant of the vehicle and the corre-
sponding door trim panel.
Impact detection zones
A. Front impact zone.
B. Side impact zone.
Deactivating the front
passenger's front airbag
To ensure the safety of your child, it is
essential to deactivate the passenger's
airbag when you install a rear-facing
child seat on the front passenger seat.
Otherwise, the child would risk being
seriously injured or killed if the airbag
w e r e t o i n fl a t e .
With the ignition switched off , insert
the key into the passenger's airbag de-
activation switch, turn it to the "OFF"
position, then remove the key keeping
the switch in the new position. Reactivation
As soon as the child seat is removed,
turn the airbag switch to the
"ON" po-
sition to reactivate the airbag and thus
ensure its safety function.
System which protects the driver in the
event of a serious side impact in order
to limit the risk of injury to the chest.
T h e l a t e r a l a i r b a g i s fi t t e d i n t h e s e a t
back frame, on the door side. When the ignition is on, this
warning lamp remains lit on the
instrument panel if the passen-
ger's airbag is deactivated.
If this warning lamp comes on,
accompanied by an audible
signal and a message on the
multifunction screen, contact a
PEUGEOT dealer to have the airbag
system checked. In the
"OFF" position, the passenger's
airbag will not be triggered in the event
of an impact.
Page 63 of 107
!
67
The incorrect installation of a child
seat in a vehicle compromises the
child's protection in the event of an
accident.
Remember to fasten the seat belts
or the child seat harnesses keep-
ing the slack in relation to the
child's body to a minimum , even
for short journeys.
For optimum installation of the "for-
ward facing" child seat, ensure that
the back of the child seat is in con-
tact with the back of the vehicle's
seat and that the head restraint
does not cause any discomfort.
If the head restraint has to be re-
moved, ensure that it is stored or
attached securely to prevent it from
being thrown around the vehicle in
the event of sharp braking.
Children under the age of 10 must
not travel in the "forward facing"
position on the front passenger
seat, unless the rear seats are al-
ready occupied by other children,
cannot be used or are absent. Installing a booster seat
The chest part of the seat belt must
be positioned on the child's shoulder
without touching the neck.
Ensure that the lap part of the seat
belt passes correctly over the child's
thighs.
PEUGEOT recommends the use of
a b o o s t e r s e a t w h i c h h a s a b a c k , fi t -
ted with a seat belt guide at shoulder
level.
As a safety precaution, do not leave:
- one or more children alone and
unsupervised in a vehicle,
- a child or an animal in a vehicle which is exposed to the sun, with
the windows closed,
- the keys within reach of children inside the vehicle.
To prevent accidental opening of the
doors, use the "Child lock".
Take care not to open the rear win-
dows by more than one third.
To protect young children from the
r a y s o f t h e s u n , fi t s i d e b l i n d s o n t h e
rear windows.
CHILD LOCK
On each rear door, this prevents open-
ing of the door from the inside.
Turn control 1 an eighth turn (45 degrees)
towards the inside of the vehicle using the
ignition key.
Check that the safety lock is engaged
correctly. The control 1 should no longer
be in the vertical position.
Page 71 of 107
!
76
CHECKING THE LEVELS Brake fluid level Used oil
Oil level
Check the level regularly
and top up between chang-
es. The maximum consump-
tion is 0.5 litre per 600 miles
(1 000 km).
Check the level with the vehicle level,
engine cold, using the dipstick. T h i s fl u i d m u s t a l w a y s b e a t t h e
maximum level.
T h e b r a k e fl u i d m u s t b e c h a n g e d
according to the manufacturer's
servicing schedule.
U s e fl u i d s r e c o m m e n d e d b y t h e m a n u -
f a c t u r e r , w h i c h f u l fi l D O T 4 s t a n d a r d s .
Note : b r a k e fl u i d i s h a r m f u l t o h e a l t h
and very corrosive. Avoid all contact
with the skin.
Cooling system
Dipstick
There are two marks on the
dipstick:
A = maximum
N e v e r fi l l p a s t t h i s m a r k .
B = minimum
Power steering reservoir
Open the reservoir, with the engine at
ambient temperature. The level should
always be above the MIN. mark and
close to the MAX. mark.
Oil change
According to the information given in
the Warranty and Maintenance Record.
Viscosity selection
In all cases, the oil used must meet the
manufacturer's requirements. Windscreen wash level Avoid used oil coming into pro-
longed contact with the skin.
Empty the used oil into the con-
tainers intended for this purpose
in the PEUGEOT network.
Do not dispose of used oil, brake
fl u i d o r c o o l a n t i n t o d r a i n s o r o n t o
the ground.
T h i s fl u i d m u s t a l w a y s b e a t t h e
maximum level (circular line).
U s e t h e fl u i d r e c o m m e n d e d b y
the manufacturer.
When the engine is warm, the tempera-
ture of the coolant is controlled by the
engine fan. As this fan can operate with
the ignition key removed and because
the cooling system is pressurised, wait
for at least one hour after the engine has
stopped before carrying out any work.
Slacken the cap by two turns to release
the pressure to prevent any risk of scald-
ing. When the pressure has dropped,
remove the cap and top up the level.
Note: the coolant does not need to be
changed. For best quality cleaning and to
a v o i d f r e e z i n g , t h i s fl u i d m u s t
not be topped up or replaced
with water.
To maintain the reliability of engines
and emission control systems, the use
of additives in engine oil is prohibited.
Page 88 of 107
!i
92
ECONOMY MODE FUNCTION
After the engine has stopped, with the
key in the accessories position, certain
functions (windscreen wiper, courtesy
lamps, audio equipment, dipped beam
headlamps, etc.) can only be used for
a maximum cumulative duration of ap-
p r o x i m a t e l y fi f t e e n m i n u t e s , t o p r e v e n t
discharging of the battery.
O n c e t h e fi f t e e n m i n u t e s a r e o v e r , t h e
message "Economy mode active" ap-
pears on the multifunction screen and
the active functions are put on standby.
These functions will be reactivated au-
tomatically the next time the vehicle is
used.
To resume the use of these functions
immediately, start the engine and let it
run for a few minutes.
The time available will then be double
the time for which the engine is left run-
ning. However, this time will always be
b e t w e e n fi v e a n d fi f t e e n m i n u t e s .
A fl a t b a t t e r y w i l l p r e v e n t t h e e n -
gine from starting.
TOWING THE VEHICLE
Procedure for having your vehicle towed.
Towing your vehicle
On the front bumper, unclip the cover
to gain access to the towing eye.
Switch on the hazard warning lamps
on the towed vehicle.
Place the gear lever in neutral. Towing another vehicle
Failure to comply with this special
requirement may result in damage
to certain braking components
and the absence of braking assis-
tance the next time the engine is
started.