fuel Peugeot 206 P Dag 2010 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2010, Model line: 206 P Dag, Model: Peugeot 206 P Dag 2010Pages: 107, PDF Size: 3.94 MB
Page 1 of 107
15
PETROL - DIESEL MANUAL GEARBOX INSTRUMENT PANELS
Panel which groups together the vehicle operation dials and indicator lamps.
4. Speedometer.
Indicates the current speed of the moving vehicle (km/h).
5. Screen
.
6. Screen display
zero reset button.
Resets the selected function to zero (trip distance recorder or service in-
dicator).
7. Instrument panel lighting button.
Adjusts the brightness of the lighting of the instrument panel.
DIALS
1. Rev counter.
Indicates the speed of rotation of the engine (x 1 000 rpm).
2. Fuel gauge.
Indicates the quantity of fuel remain- ing in the tank.
3. Coolant
temperature.
Indicates the temperature of the en- gine coolant (° Celsius).
A. Cruise control.
Speed limiter.
(km/h)
B. Trip distance recorder.
(km)
C. Service indicator.
(km) then,
Distance recorder.
(km)
These three functions are displayed in succession when the ignition is
switched on.
For more information, refer to the sec-
tion which corresponds to the function
and to the display associated with it.
Display
Page 6 of 107
INSTRUMENTS and CONTROLS
20
Warning lamp is on Cause Action/Observations
Engine
autodiagnosis system fi x e d . The emission control system
has a fault. This lamp should switch off when the engine is sta
rted.
If it does not switch off, contact a PEUGEOT deale r
urgently.
fl a s h i n g . The engine management
system has a fault. Risk of destruction of the catalytic convertor.
Have it checked by a PEUGEOT dealer.
Low fuel level fi x e d w i t h t h e
needle in the red zone. W h e n i t fi r s t c o m e s o n t h e r e
remains approximately
5 litres
of fuel in the tank.
At this point, you begin to use
the fuel reserve. Refuel as soon as possible to avoid running
out of fuel.
This warning lamp will come on every time
t h e i g n i t i o n i s s w i t c h e d o n , u n t i l a s u f fi c i e n t
addition of fuel is made.
Fuel tank capacity: approximately
50 litres .
Never continue to drive until you run out
of fuel, as this could damage the emission
control and injection systems.
Maximum
coolant
temperature fi x e d w i t h t h e
needle in the red zone. The temperature of the cooling
system is too high. Stop as soon as it is safe to do so.
Wait until the engine has cooled down before
topping up the level, if necessary.
If the problem persists, contact a PEUGEOT
dealer.
Engine oil
pressure fi x e d . There is a fault with the engine
lubrication system. Stop as soon it is safe to do so.
Park, switch off the ignition and contact a
PEUGEOT dealer.
Page 8 of 107
ii
INSTRUMENTS and CONTROLS
22
COOLANT TEMPERATURE
INDICATOR
System which informs the driver of the
changes in the temperature of the en-
gine coolant while driving.
With the engine running, when the nee-
dle is:
- in zone A , the temperature is correct,
- in zone B , the temperature is too
high; the max temperature warning
lamp
1 and the central STOP warn-
ing lamp come on, accompanied by
an audible signal and a message on
the multifunction screen.
You MUST stop as soon as it is safe
to do so.
Consult a PEUGEOT dealer. After driving for a few minutes, the tem-
perature and pressure in the cooling
system increase.
To top up the level:
wait for the engine to cool,
unscrew the cap by two turns to al-
low the pressure to drop,
when the pressure has dropped, re-
move the cap,
top up the level to the "MAX" mark
(circular line).
On petrol engines, the cooling of
the engine is managed electroni-
cally to reduce fuel consumption.
Consequently, the coolant tem-
perature levels are no longer sim-
ply linked with the external ambient
conditions and the use of the ve-
hicle.
For example, in town, it is normal
for the coolant temperature to be
slightly higher in cold weather than
in hot weather.
Page 13 of 107
27
MONOCHROME SCREEN B
This enables the following information
to be displayed:
- time,
- date,
- a m b i e n t t e m p e r a t u r e * ( t h i s fl a s h e s when it is between -3 and 3 °C),
- status of the doors. The display shows you, by means of a graphic,
whether a door is open,
- warning messages (e.g. ''battery charge fault'') or information mes-
sages (e.g. "fuel level low''), dis-
played temporarily, can be cleared
by pressing button 1 or 2 ,
- trip computer. Setting the parameters
Press button
1 for two seconds to access
t h e s e t t i n g s . T h e i n f o r m a t i o n fl a s h e s t o
s h o w i t i s r e a d y t o b e m o d i fi e d .
Then, individual presses on button 1
allow you to scroll through the various
data in the following sequence:
- language in which the information is displayed,
- unit of distance (kms or miles),
- unit of temperature (degrees Celsius or Fahrenheit),
- time format (12 then 24 hour mode),
- hour,
- minutes,
- year,
- month,
- day.
Pressing button 2 allows you to change
the information selected. Maintain the
pressure for rapid scrolling.
After 7 seconds without operation, the
screen returns to the normal display
a n d t h e m o d i fi e d d a t a i s r e c o r d e d .
Note: Pressing button 2 b r i e fl y d i s p l a y s t h e
outside temperature for a few seconds.
When the ambient temperature is be-
tween -3° and 3 °C, the temperature
display takes priority over the time on
the screen.
* With digital air conditioning only.
Page 14 of 107
INSTRUMENTS and CONTROLS
28
SCREEN B
TRIP COMPUTER
ZERO RESET
Press the stalk for more than two seconds.
Range
This shows the distance that can still be
covered with the fuel remaining in the
tank.
Note: t h i s fi g u r e m a y i n c r e a s e i f t h e r e
is a change in the style of driving or the
r o a d s u r f a c e , p r o d u c i n g a s i g n i fi c a n t
drop in current fuel consumption.
When the range is less than 20 miles
(30 km), three segments are dis-
p l a y e d . A f t e r fi l l i n g w i t h f u e l , t h e r a n g e
is displayed when it exceeds 60 miles
(100 km).
If horizontal segments are displayed for
long periods instead of digits, contact a
PEUGEOT dealer.
Pressing the button on the end of the
wiper
stalk enables the following data
to be displayed:
- range
- distance travelled
- average fuel consumption
- current fuel consumption
- average speed Average fuel consumption
This is the average fuel consumption
since the computer was last set to zero.
Current fuel consumption
This is the average fuel consumption
during the last few seconds.
This function is displayed only when the
vehicle is travelling at a speed greater
than 20 mph (30 km/h). Distance travelled
This indicates the distance travelled
since the computer was last set to
zero.
Average speed
This is the average speed calculated
since the computer was last set to zero
(with the ignition on).
Page 19 of 107
33
Demisting - defrosting
To quickly demist or defrost the wind-
screen and side windows:
place the air intake control 4 in the
" E x t e r i o r a i r i n t a k e " p o s i t i o n ,
place the air distribution dial 3 in the
" W i n d s c r e e n " p o s i t i o n ,
place the temperature dial 1 and the air
fl o w d i a l 2 in the maximum position,
close the central vents,
switch on the air conditioning by
pressing the "A/C" button.
5. Air conditioning On/Off
S w i t c h i n g o n
Press the "A/C" button, the associ-
ated indicator lamp comes on.
The air conditioning does not operate
w h e n t h e a i r fl o w a d j u s t m e n t d i a l 2 i s
in position "OFF".
S w i t c h i n g o f f
Press the "A/C" button again, the
associated indicator lamp switches
off.
HEATED REAR SCREEN
S w i t c h i n g o n
The heated rear screen can only oper-
ate when the engine is running.
Press this button to demist/defrost the
rear screen. The indicator lamp asso-
ciated with the button comes on.
S w i t c h i n g o f f
The heated rear screen switches off
automatically to prevent an excessive
consumption of current.
It is possible to stop the demist-
ing/defrosting operation before it is
switched off automatically by press-
ing the button again. The indicator
lamp associated with the button
switches off.
If the engine is switched off before the
heated rear screen is switched off auto-
matically, demisting/defrosting will resume
next time the engine is switched on.
Switch off the heated rear screen as
soon as appropriate as lower cur-
rent consumption results in reduced
fuel consumption. The control button is located on
the air conditioning system con-
trol panel.
The air conditioning is designed
to operate effectively in all sea-
sons, with the windows closed.
It enables you to:
- lower the temperature, in summer,
- increase the effectiveness of the demisting, in winter above 0 °C.
Page 20 of 107
33
Demisting - defrosting
To quickly demist or defrost the wind-
screen and side windows:
place the air intake control 4 in the
" E x t e r i o r a i r i n t a k e " p o s i t i o n ,
place the air distribution dial 3 in the
" W i n d s c r e e n " p o s i t i o n ,
place the temperature dial 1 and the air
fl o w d i a l 2 in the maximum position,
close the central vents,
switch on the air conditioning by
pressing the "A/C" button.
5. Air conditioning On/Off
S w i t c h i n g o n
Press the "A/C" button, the associ-
ated indicator lamp comes on.
The air conditioning does not operate
w h e n t h e a i r fl o w a d j u s t m e n t d i a l 2 i s
in position "OFF".
S w i t c h i n g o f f
Press the "A/C" button again, the
associated indicator lamp switches
off.
HEATED REAR SCREEN
S w i t c h i n g o n
The heated rear screen can only oper-
ate when the engine is running.
Press this button to demist/defrost the
rear screen. The indicator lamp asso-
ciated with the button comes on.
S w i t c h i n g o f f
The heated rear screen switches off
automatically to prevent an excessive
consumption of current.
It is possible to stop the demist-
ing/defrosting operation before it is
switched off automatically by press-
ing the button again. The indicator
lamp associated with the button
switches off.
If the engine is switched off before the
heated rear screen is switched off auto-
matically, demisting/defrosting will resume
next time the engine is switched on.
Switch off the heated rear screen as
soon as appropriate as lower cur-
rent consumption results in reduced
fuel consumption. The control button is located on
the air conditioning system con-
trol panel.
The air conditioning is designed
to operate effectively in all sea-
sons, with the windows closed.
It enables you to:
- lower the temperature, in summer,
- increase the effectiveness of the demisting, in winter above 0 °C.
Page 43 of 107
50
FUEL TANK
R e s e r v o i r w h i c h s h o u l d b e r e fi l l e d w i t h
fuel, when the minimum level has been
detected.
Fuel tank capacity: approximately
50 litres. Filling
A l a b e l a f fi x e d t o t h e i n s i d e o f t h e t a n k
reminds you of the type of fuel to be
used depending on your engine.
More than 5 litres of fuel must be add-
ed in order to be registered by the fuel
gauge.
The key cannot be removed from the
l o c k u n t i l t h e fi l l e r c a p i s r e fi t t e d .
Opening the cap may release a vacu-
um, indicated by a noise. This is caused
by the sealing of the fuel system.
T o fi l l t h e t a n k s a f e l y :
the engine
must be
switched off,
i n s e r t t h e k e y i n t h e fi l l e r c a p , t h e n
turn it to the left,
r e m o v e t h e fi l l e r c a p ,
fi l l t h e t a n k , but do not continue
after the 3rd cut-off of the pump ;
this could cause malfunctions.
W h e n y o u h a v e fi l l e d t h e t a n k :
r e fi t t h e fi l l e r c a p ,
turn the key to the right, then remove
i t f r o m t h e fi l l e r c a p .
Page 44 of 107
5151
Quality of the fuel used for
petrol engines
The petrol engines are perfectly com-
patible with E10 type petrol biofuels
(containing 10 % ethanol), conforming
to European standards EN 228 and
EN 15376.
E85 type fuels (containing up to 85 %
e t h a n o l ) a r e r e s e r v e d e x c l u s i v e l y f o r
vehicles marketed for the use of this
t y p e o f f u e l ( B i o F l e x v e h i c l e s ) . T h e
quality of the ethanol must comply with
European standard EN 15293.
For Brazil only, special vehicles are
marketed to run on fuels containing up
to 100 % ethanol (E100 type). Quality of the fuel used for
Diesel engines
The Diesel engines are perfectly com-
patible with biofuels which conform to
current and future European standards
(Diesel fuel which complies with stan-
d a r d E N 5 9 0 m i x e d w i t h a b i o f u e l w h i c h
complies with standard EN 14214)
available at the pumps (containing up
to 7 % Fatty Acid Methyl Ester).
The B30 biofuel can be used in cer-
tain Diesel engines; however, this use
is subject to strict application of the
special servicing conditions. Consult a
PEUGEOT dealer.
The use of any other type of (bio)fuel
(vegetable or animal oils, pure or dilut-
ed, domestic fuel...) is strictly prohibited
(risk of damage to the engine and fuel
system).
Page 69 of 107
74
BONNET
Component which protects and provides
access to the components of the engine
for checking of the various levels.
- At the front, lift the safety catch and raise the bonnet. - Secure the stay to hold the bonnet
open.
Closing
- Put the stay back in its housing.
- Lower the bonnet and release it at the end of its travel.
- Check that the bonnet is locked.
RUNNING OUT OF FUEL
(DIESEL)
If you should run out of fuel, it is neces-
sary to prime the fuel system:
- fi l l t h e f u e l t a n k w i t h a t l e a s t fi v e l i t r e s of diesel,
- squeeze and release the manual priming pump, located under the
bonnet under the protective cover,
until fuel appears in the transparent
pipe,
- operate the starter until the engine starts.
Opening
- Pull the release lever located on the
left, below the dashboard.
When the engine is hot, handle the
safety catch and the bonnet stay with
care (risk of burns).