engine Peugeot 208 2012 Service Manual

95
4
Driving











Stop & Start
The Stop & Star t system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...).
The engine restar ts automatically - START mode - as soon as you want to move off. The restar t takes place instantly, quickly and silently.
Per fect for urban use, the Stop & Star t system reduces fuel consumption and exhaust emissions as well as the noise level when stationary.


Operation


Going into engine STOP mode
The "ECO"warning lamp comes
on in the instrument panel and the
engine goes into standby:


-
with a manual gearbox
, at speeds below
12 mph (20 km/h), when you put the gear
lever into neutral, and you release theclutch pedal.
-with a 5-speed electronic gearbox , atspeeds below 5 mph (8 km/h), when you
press the brake pedal or put the gear lever
in position N
.


Never refuel with the engine in STOPmode; you must switch off the ignition with the key.
For your comfort, during parking manoeuvres, STOP mode is not available for a few seconds after coming out of reverse gear.STOP mode does not affect the functionality of the vehicle, such as for example, braking, power steering...


Special cases: STOP mode notavailable
STOP mode is not invoked when:


- the driver's door is open,

- the driver's seat belt is not fastened,

- the vehicle has not exceeded 6 mph (10 km/h) since the last engine star t using
the key,

- the engine is needed to maintain acomfor table temperature in the passenger compartment,

- demisting is active,

- some special conditions (battery charge, engine temperature, braking assistance,
ambient temperature...) where the engine isneeded to assure control of a system.

A time counter calculates the sum
of the periods in STOP mode
during a journey. It rests itself
to zero every time the ignition is switched on with the key.
The "ECO"
warning lamp flashes for a few seconds then goes off.
This operation is perfectl
y normal.

96
Driving
The "ECO"warning lamp goes off
and the engine starts:
- with a manual gearbox
, when you
depress the clutch pedal,
- with an electronic
gearbox
:
●
gear lever in position Aor M
, when yourelease the brake pedal,
●
or gear lever in position Nand the brakepedal released, when you move the gear lever to position A
or M
,
●
or when you engage reverse gear. For reasons of safet
y and for your comfort,START mode is invoked automatically when:


Special cases: START invoked
automatically


- you open the driver's door,

- you unfasten the driver's seat belt,

- the speed of the vehicle exceeds 7 mph(11 k m / h) with an electronic gearbox,

- some special conditions (battery charge,engine temperature, braking assistance,
ambient temperature...) where the engine is
needed for control of a system.


If the system has been deactivatedin STOP mode, the engine restartsimmediately.

At any time, press the "ECO OFF"
switch todeactivate the system.
This is confirmed by the switch warning lampcoming on accompanied by a message in the screen.


Deactivation
The "ECO"
warning lamp flashes for
a few seconds, then goes off.
This operation is per fectly normal.

97
4
Driving
The system is reactivated automatically at every new star t using the key.


Reactivation

Press the "ECO OFF"switch again.
The s
ystem is active again; this is confirmed
by the switch warning lamp going off,
accompanied by a message in the screen.
Operating fault
In the event of a fault with the system, the
"ECO OFF"
switch warning lamp flashes thencomes on continuously.
Have it checked by a PEUGEOT dealer or aqualified workshop.
In the event of a fault in STOP mode, the
vehicle ma
y stall. All of the warning lamps come on. It is then necessary to switch off
the ignition and star t the engine again using
the key.

Before doing anything under the bonnet,deactivate the Stop & Start system toavoid any risk of injury resulting fromautomatic operation of STA R T m o d e .

This s
ystem requires a battery with a specialspecification and technology (reference
numbers available from a PEUGEOT dealer or
a qualified workshop).
Fitting a battery not listed byPEUGEOT introduces the risk of malfunction of
the system.



Maintenance

The Stop & Start system makes use of advanced technology. All work onthis type of battery must be done by a PEUGEOT dealer or a qualifiedworkshop.

98
Driving





Hill start assist
System which keeps your vehicle immobilised
temporarily (approximately 2 seconds) whenstarting on a gradient, the time it takes to
move your foot from the brake pedal to the accelerator pedal.
This function is only active when:
- the vehicle is completely stationary, withyour foot on the brake pedal,
- when certain conditions of gradient are met,
- with the driver’s door closed.
The hill start assist function cannot bedeactivated.
On an ascendin
g slope, with the vehiclestationary, the vehicle is held for a brief moment when you release the brake pedal:

- if you are in first gear or neutral with a
manual gearbox,

- if you are in position Aor Mwith an electronic gearbox.

- if you are in position Dor Mwith an
automatic gearbox.


Operation
On a descending slope, with the vehicle
stationary and reverse gear engaged, thevehicle is held for a brief moment when you release the brake pedal.

Do not leave the vehicle while it is beingheld in the hill star t assist phase.
If you need to leave the vehicle whilethe engine is running, apply the parking brake manually then ensure that theparking brake warning lamp is on (not flashing) in the instrument panel.


Operating fault

If a fault occurs with the system, these warninglamps come on. Contact a PEUGEOT dealer
or a qualified workshop to have the systemchecked.

110
Visibility
Daytime running lamps
Daytime lighting, compulsory in cer taincountries, which comes on automatically when
the engine is star ted making the vehicle more
visible to other users.
LED lamps
They come on when the engine is star ted.
Depending on the destination country, they are
used for:
- daytime running lamps * in day mode and
sidelamps in night mode (they are brighter
when daytime running lamps),
or
- sidelamps in day and night mode.

*

function that can be set in the vehicle configuration menu.
Thi
s function is assured:


- in countries where it is imposed by
regulations,
by illumination of the dipped beamheadlamps with the sidelamps and number plate lamps; this function cannot be deactivated.

- for other countries where it is provided,
by the use of dedicated lamps (bulbs or
LEDs); this function can be activated or
deactivated via the vehicle configurationmenu.
The lighting control stalk must be placed in the
"0"or "AU TO "
(day mode) position.
Deactivation of the daytime running lamps iseffective after operation of the lighting control
stalk or after the next engine start; activation iseffective immediately.

The instruments and controls
(instrument
panel, multifunction screen, air conditioning control panel, ...) are not illuminated, except
in night mode with manual or automatic
illumination of headlamps.

119
5
Visibility











Courtesy lamp
In this position, the cour tesy lamp comes on gradually:


Take care to avoid leaving anything in contact with the courtesy lamp. - when the vehicle is unlocked,
- when the ke
y is removed from the ignition,
- when opening a door,
- when the remote control locking button is
pressed, in order to locate your vehicle.
It switches o
ff gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- 30 seconds after the last door is closed.
Permanentl
y off.
Permanent lighting.
) With the ignition on, press
the corresponding switch.
1.Front cour tesy lamp2. Map reading lamp s
With the "permanent lighting" mode, the lightingtime varies according to the circumstances:

- with the ignition off, approximately ten
minutes,

- in energy economy mode, approximatelythirty seconds, -with the engine running, unlimited.



Front map reading lamps

123
6
Safety
Electronic Stability Programme incorporatingthe following systems:


- the anti-lock braking system (ABS) and the electronic brake force distribution (EBFD),

- the emergency braking assistance,

- the anti-slip regulation (ASR) or tractioncontrol,

- the d
ynamic stability control (DSC).






























Electronic stability programme (ESP)
Definitions
Anti-lock braking system (ABS)
and electronic brake force
distribution (EBFD)
This system improves the stability and
manoeuvrability of your vehicle when braking and provides improved control in corners, in par ticular on poor or slippery road surfaces.
The ABS prevents wheel lock in the event of
emergency braking.
The electronic brake
force distribution system
manages the braking pressure wheel by wheel.
Emergency braking assistance
In an emergency, this system enables you to reach the optimum braking pressure more
quickly and therefore reduce the stopping distance. It is triggered in relation to the speed at which
the brake pedal is pressed. This is felt by a reduction in the resistance of the pedal and an increase in the effectiveness of the braking.

Anti-slip regulation (ASR)

The ASR system (also known as Traction Control) optimises traction in order to avoid
wheel slip by acting on the brakes of the drivingwheels and on the engine. It also improves
the directional stability of the vehicle onacceleration.


Dynamic stability control(DSC)

If there is a difference between the path
followed by the vehicle and that required bythe driver, the DSC monitors each wheel and
automatically acts on the brake of one or more
wheels and on the engine to return the vehicle
to the required path, within the limits of the laws of physics.

125
6
Safety
Dynamic stability control(DSC)

Activation
This system is activated automatically eachtime the vehicle is started.
It comes into operation in the event of a grip or
trajectory problem.
This is indicated b
y flashing of thiswarning lamp in the instrument panel.




Deactivation

In exceptional conditions (starting a vehicle
which is bogged down, stuck in snow, on soft ground...), it may be advisable to deactivate
the DSC system, so that the wheels can move
freely and regain grip.

The DSC system offers exceptional safety in normal driving, but this should not encourage the driver to take extra risks or drive at high speed.
The correct operation of the system depends on obser vation of the manufacturer's recommendationsregarding the wheels (tyres and rims),the braking components, the electronic components and the PEUGEOT assembly and operation procedures.
After an impact, have the system
checked by a PEUGEOT dealer or a qualified workshop.



Operating fault
If this warning lamp comes on,accompanied by an audible signaland a message in the screen, this
indicates a fault with the system.
Contact a PEUGEOT dealer or a qualified
workshop to have the system checked.
Reactivation
The system is reactivated automatically eachtime the ignition is switched back on or from 30 mph (50 km/h).)
Press the switch again to reactivate it
manually. But it is recommended that the s
ystem bereactivated as soon as possible.) Press the switch.
The indicator lamp in the switch comes on: the
DSC system no longer acts on the operation of
the engine.

145
7
Practical information

Repair procedure


1. Sealing
)Switch off the ignition. )Turn the selector A
to the "sealant"position.)Check that the switch B
is in position "O".
)
Uncoil the white pipe G
fully.)
Unscrew the cap from the white pipe.)
Connect the white pipe to the valve of the
tyre to be repaired.
) Connect the compressor's electric plug to
the vehicle's 12 V socket. ) Star t the vehicle and leave the engine
running.
Take care, this product is harmful (e.g. ethylene-glycol, colophony...) if swallowed and causes irritation to theeyes.Keep it out of reach of children.

Avoid removing any foreign bodieswhich have penetrated into the tyre.

147
7
Practical information

2. Infl ation
)Turn the selector A
to the "air" position.)Uncoil the black pipe Hfully. )Connect the black pipe to the
valve of the wheel.
) Connect the compressor's electric plug to
the vehicle's 12 V socket.) Star t the vehicle again and leave theengine running.
)
Adjust the pressure using the compressor (to inflate: switch B
in position "I"
; to deflate: switch B
in position "O"and press button C), in accordance with the vehicle's
tyre pressure label (located on the left hand
door aperture).
A loss of pressure indicates that thepuncture has not been fully plugged; contact a PEUGEOT dealer or qualified
workshop for assistance. ) Remove and stow the kit. )Drive at reduced speed (50 mph [80 km/h] max)limiting the distance travelled to approximately
120 miles
(200 km).
)Visit a PEUGEOT dealer or aqualified workshop as soon aspossible. You must inform the technician that you have used this kit. After
inspection, the technician willinform you whether the tyre can berepaired or must be replaced.