change time Peugeot 208 2012 Owner's Manual

.
19
Familiarisation















































Eco-driving
Eco-driving is a range of everyday practices that allow the motorist to optimise their fuel consumption and CO2 emissions.
Optimise the use of your
gearbox
With a manual gearbox, move off gently, change up without waiting and drive by changing up quite soon. If your vehicle has
the system, the gear shift indicator invites youto change up; it is displayed in the instrumentpanel, follow its instructions.
With an automatic or electronic gearbox, stay in Drive "D"or Auto "A"
, according to the type of gearbox, without pressing theaccelerator pedal heavily or suddenly.
Drive smoothly
Maintain a safe distance between vehicles,use engine braking rather than the brake pedal, and press the accelerator progressively.These practices contribute towards a reductionin fuel consumption and CO2 emissions andalso helps reduce the background traffic noise.
If your vehicle has cruise control, make use of the system at speeds above 25 mph (40 km/h) when the traffic is flowing well.



Control the use of your
electrical equipment
Before moving off, if the passenger compartment is too warm, ventilate it byopening the windows and air vents before using the air conditioning.
Above 30 mph (50 km/h), close the windowsand leave the air vents open. Remember to make use of equipment that canhelp keep the temperature in the passenger compartment down (sunroof and window blinds...).Switch off the air conditioning, unless it has automatic digital regulation, as soon as the desired temperature is attained.Switch off the demisting and defrosting controls, if not automatic.Switch off the heated seat as soon as possible.


Switch off the headlamps and front foglampswhen the level of light does not require their use.

Avoid running the engine before moving off,particularly in winter; your vehicle will warmup much faster while driving.

As a passenger, if you avoid connecting your multimedia devices (film, music, video game...), you will contribute towards limitingthe consumption of electrical energy, and soof fuel.
Disconnect your por table devices beforeleaving the vehicle.

42
Instruments and controls
Stop & Start timecounter
(minutes / seconds or hours / minutes)
If your vehicle is fitted with Stop & Star t, a timecounter calculates the time spent in STOP mode during a journey. It resets to zero every time the ignition isswitched on with the key.


If dashes are displayed continuously while driving in place of the digits, contact a PEUGEOT dealer or a qualified workshop.
This function is only displayed from 20 mph (30 km/h).

This value may vary following a changein the style of driving or the relief,resulting in a significant change in thecurrent fuel consumption.
A few definitions (trip computer)

Range
(miles or km)
This indicates the distancewhich can still be travelled with
the fuel remaining in the tank
in relation to the average fuelconsumption over the last few
miles (kilometres) travelled.
When the ran
ge falls below 20 miles (30 km),
dashes are displayed. After filling with at least 5 litres of fuel, the range is recalculated and is
displayed when it exceeds 60 miles (10 0 km).
Current fuel consumption
(mpg or l/100 km or km/l)
This is the average fuel consumption
during the last few seconds.
Average fuel consumption
(mpg or l/100 km or km/l)
This is the average fuel consumptionsince the last trip computer zero
reset.
Average speed
(mph or km/h)This is the average speed calculatedsince the last trip computer zero reset(ignition on).
Distance travelled
(miles or km)This indicates the distance
travelled since the last trip
computer zero reset.

87
4
Driving

Never select neutral N
while the vehicleis moving. Only engage reverse gear Rwhen thevehicle is immobilised, with your foot on the brake pedal. In all cases, you must apply the parkingbrake to immobilise the vehicle.



"Au t o s equential" mode

In the automated mode, you can resumecontrol temporarily at any time using thesteering mounted control paddles.
The use of these paddles permits manual
selection of the gears in situations which
require a more rapid change-down than in
the automated mode (arrival at a roundabout,leaving a car park with a steep gradient,
over taking...).
The gearbox engages the required gear if
the engine speed permits. AUTO
remains
displayed on the instrument panel.
After a few moments, the gearbox resumes
automatic control of the gears.
"Snow" automated mode
In the automated mode, if the vehicle detects poor grip, the gearbox will change automatically
to the automated "snow" mode.
AUTO
and 7
appear in the
instrument panel.
Reinitialisation
Following disconnection of the battery, the gearbox must be reinitialised.) Switch on the ignition.
AUTO , 7and -appear in the instrument panel.


Operating fault

With the ignition on, if this warninglamp comes on and AUTOflashes, accompanied by an
audible signal and a message in the screen,
this indicates a
gearbox fault.
Have it checked by a PEUGEOT dealer or a qualified workshop.


For best acceleration, when over taking another vehicle for example, press the accelerator pedal firmly to pass the
point of resistance.

Stopping the vehicle
Before switching off the engine, you canchange to position N
to be in neutral.
In this case, you must apply the parking brake to immobilise the vehicle.
)
Select position N.)
Press the brake pedal.)
Wait approximately 30 seconds until Nor a gear appears in the instrument panel. )
Release the brake pedal.
The gearbox is operational again.

93
4
Driving
)Apply the parking brake. )Select position P or N.)Star t the engine.
If this procedure is not followed, there is an
audible signal, accompanied by the display of
an warning message.)With the engine running, press the brake pedal. )Release the parking brake. )Select position R, Dor M.)Gradually release the brake pedal.
The vehicle moves off immediately.


Moving off


When the engine is running at idle, with the brakes released, if position R, D
or M
is selected, the vehicle moves evenwithout the accelerator being pressed.
When the engine is running, never leave children in the vehicle without supervision. When carrying out maintenance with the engine running, apply the parkingbrake and select position P
.
P


If position N
is selected inadver tently while driving, allow the engine toreturn to idle then select position D
toaccelerate.
Never select position N
while the vehicle is moving.Never select positions P
or Runless thevehicle is completely stationary.

Automatic operation
)
Select position Dfor automaticchanging
of the four gears.The gearbox then operates in auto-adaptivemode, without any inter vention on the par t
of the driver. It continuously selects the most suitable gear according to the style of
driving, the profile of the road and the load in
the vehicle.
For maximum acceleration without touching the gear lever, press the accelerator pedal downfully (kick down). The gearbox changes downautomatically or maintains the gear selecteduntil the maximum engine speed is reached.On braking, the gearbox changes downautomatically to provide efficient engine
braking.
If you release the accelerator sharply, thegearbox will not change to a higher gear for
safety reasons.

Sport and snow programmes


Sport programme "S"
)
Press button "S", after star ting the engine.
The
gearbox automatically favours a dynamic style of driving.
S
appears in the instrument panel.


Snow programme " 7"
)
Press button "7
", after star ting the engine.
The gearbox adapts to driving on slipperyroads.
This programme improves star ting and drive
when traction is poor.
7 appears in the instrument panel.



Return to automatic operation
)
At any time, press the button selected
again to quit the programme engaged and
return to auto-adaptive mode.
These two special programmes supplement the
automatic operation in very specific conditions of use.

94
Driving
Manual operation
)Select position M for sequentialchanging
o
f the four gears.)Push the lever towards the + sign tochange up a gear. )Pull the lever towards the -
sign to change
down a gear.
It is only possible to change from one gear to another if the vehicle speed and engine speedpermit; otherwise, the gearbox will operate
temporarily in automatic mode.
D disappears and the gears engaged appear in succession in the
instrument panel.

Invalid value during manual operation
This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).



Stopping the vehicle

Before switching off the engine, you can engage
position P or N
to place the gearbox in neutral.
In both cases, apply the parking brake to
immobilise the vehicle.

Operating fault
When the ignition is on, thelighting of this warning lamp,
accompanied by an audible signal and a
message in the multifunction screen, indicates
a gearbox fault.
In this case, the gearbox switches to back-up mode and is locked in 3rd gear. You may feel
a substantial knock when changing from Pto Rand from N to R
. This will not cause any damage to the gearbox.
Do not exceed 60 mph (10 0 km/h), local speed
restrictions permitting.

Contact a PEUGEOT dealer or a qualified
workshop as soon as possible.
I
f the engine speed is too low or too high, the
gear selected flashes for a few seconds, then
the actual gear engaged is displayed.
It is possible to change from position D(automatic) to position M (manual) at any time.
When the vehicle is stationary or movingvery slowly, the gearbox selects gear M1automatically. The spor t and snow programmes do not
operate in manual mode.

There is a risk of damage to thegearbox:


- if you press the accelerator and brake pedals at the same time,

- if you force the movement of the gear lever from the Pposition toanother position when the battery isflat.
To reduce fuel consumption when at
a prolonged standstill with the enginerunning (traffic jam...), put the gear lever in the Nposition and apply the parkingbrake.

If the lever is not in position P
, when the Pdriver's door is opened or approximately 45 seconds after the ignition is switchedoff, a warning message appears in the screen.)Return the lever to position P; the
message disappears.

181
7
Practical information
The fitting of electrical equipment or accessories which are not recommended by PEUGEOT may resultin a failure of your vehicle's electronicsystem and excessive electrical consumption. Please note this precaution. Youare advised to contact a PEUGEOTrepresentative to be shown the range of recommended equipment and accessories.


Installation of radio communication transmitters

Before installing any after-market radio communication transmitter, you can contact a PEUGEOT dealer for the specification of transmitters which canbe fitted (frequency, maximum power, aerial position, specific installationrequirements), in line with the VehicleElectromagnetic Compatibility Directive(2004/104/EC).




Depending on the legislation in forcein the country, it may be compulsory to have a high visibility safety vest,warning triangle and spare bulbs andfuses available in the vehicle. B
y visiting a PEUGEOT dealer, you can also
obtain products for cleaning and maintenance (exterior and interior) - including ecological products in the "TECHNATURE" range, toppingup products (screenwash...), touch-up pens and paint aerosols for the exact colour of your
vehicle, refills (cartridge for the temporary puncture repair kit...), ...



"Multimedia":

audio systems, por table satellite navigationsystems, semi-integral suppor t for por tablesatellite navigation system, hands-free kit, CDchanger, speakers, DVD player, connection
kit for MP3 or CD player, USB Box, Wi-Fi on-board...

194
Checks






Checks
12 V battery

The battery does not require any maintenance.
However, check that the terminals are clean
and correctl
y tightened, particularly in summer and winter.
When carrying out work on the battery, refer to the
"Practical information" section for details of the precautions
to be taken before disconnecting the battery and following its reconnection.
The presence of this label, in particular with
the Stop & Star t system, indicates the use of a specific 12 V lead-acid battery with special
technology and specification. The involvement
of a PEUGEOT dealer or a qualified workshop
is essential when replacing or disconnecting
the battery.
Par ticle emissions filter (Diesel)

The start of saturation of thepar ticle filter is indicated by the
temporary illumination of this warning lamp
accompanied by a warning message in the screen.
As soon as the traffic conditions permit,
regenerate the filter by driving at a speed of at
least 40 mph (60 km/h) until the warning lamp
goes off.
If the warning lamp stays on, this indicates a
low additive level.

On a new vehicle, the first par ticlefilter regeneration operations may be accompanied by a "burning" smell,
which is perfectly normal.
Following prolonged operation of the vehicle at very low speed or at idle, you may, in exceptional circumstances,notice the emission of water vapour at the exhaust on acceleration. This does not affect the behaviour of the vehicle or the environment. Unless other wise indicated, check these components in accordance with the ser vicin
g booklet and according to your engine.Other wise, have them checked by a PEUGEOT dealer or a qualified workshop.
Air filter and passenger compartment filter

Refer to the ser vicing booklet for
details of the replacement inter vals
for these components.
Depending on the environment (e.g.
dusty atmosphere) and the use of the vehicle(e.g. city driving), replace them twice as oftenif necessary.y A clogged passenger compar tment filter may
have an adverse effect on the performance
of the air conditioning system and generateundesirable odours.
Oil filter
Replace the oil filter each time theengine oil is changed.
Refer to the servicing booklet for
details of the replacement inter val for
this component.

04

ADDING A WAYPOINT
ORGANISING WAYPOINTS

Select "Navigation GPS ".

Select "Waypoints
".

Select "Add
".

The address of the wa
ypoint is entered in
the same way as a destination, so enter
the " City" or post code, the "Street" andthe " N°". Confi rm each time.
Th
en select " As waypoint
".
Select the wa
ypoint that you want to move in
the order.
To or
ganise waypoints, carry out the previous operations 1 to3 again (Adding a waypoint).

Select "Up
".

Select "Down".

Select "Delete
".

Select "Roadmap
" to view the changes made
to the route.
Select "Guide
".

Select the criteria then "Confi rm
" to start guidance and give the general direction of the navigation route.

Pr
ess MENUto display the " MAIN MENU
" then select " Navigation".
NAVIGATION - GUIDANCE

Select "Address
".

251
"Search"
"Settings"
- List of telephones already paired with the audio system. C1
- Display a description of the telephone. C2
- Connect/disconnect the selected telephone. C3
- Start the search for another peripheral so as to connect it to theC4 audio system via Bluetooth.
- Your Bluetooth settings.C7
- Import contacts from the telephone to the audio system.C71
- Make the audio system (telephone, ...) visible externally viaC72 Bluetooth.
Setting the answering time for an incoming call.

"CALL" (shortcut menu)

- List of outgoing, missed and incoming calls. D1
- Delete the selected telephone.
C5
- Import the contacts from the selected telephone to store them in C6 the audio system.
"Bluetooth"


Access to the "Communications" menu (continued)
- Enter an number using the keypad.
D2
Then press "CALL" to start the call.

- List of contacts saved in the telephone.
D3
For more information, refer to the "Contacts" menu.
- End the current call.
D4
- Duration, name and number of the contact for the current call.
D5
- "Switch call": change contact while retaining the current contact. "Conference call": accept the incoming call and communicate with more than one person.
D6
- "Micro OFF": cut the microphone temporarily so that the contact does not hear your conversation with a passenger.
D7
- "Privacy mode": transfer to your telephone for a private conversation or to leave the vehicle without ending the call.
D8
- Quit this shortcut menu.
D9

259

Access to the "Settings" menu


"System"
- Select the language then confi rm.


A2
- Select the data from the list then press "Delete".
A5
- Restore original settings.
A6
"Display"
- Brightness setting.
A1
- Modify the screen brightness in daylight.
A11
- Press to switch off the screen. Press the screen again (anywhere
A13 on its surface) to switch it on again.

"Units"
- Setting units.
A4
- Select the units used for the display of distance and fuel
A41 consumption.
- Select the units for the display of temperature.
A42


"Date & Time"
- Setting the date and time.
A3
- Adjust the time.
A31
- Adjust the date.
A32
- Adjust the time zone.
A33
- Synchronise the time with GPS, change the time display format.
A34