fog light Peugeot 208 2012 Owner's Manual

4
Familiarisation
Stop & Start
This system puts the engine temporarily into standby during stops in the traffic (red lights, traffic jams, etc...). The engine restar ts automatically as soon as you want to move off. Per fectly suited to
urban use, the Stop & Start system reduces fuel consumption, exhaust emissions and thlevel when stationary.
95

Electronic stability programme

This system allows you to maintain the
directional stability of the vehicle, within the
laws of physics.
12
3
Exterior
Cornering lighting
At low speed this system provides additional
lighting in corners, at junctions, when parking..., making use of the corresponding front foglamp.
114

.
13
Familiarisation
Seeing clearly


Lighting

Ring A

Ring B
Wipers
107
Control stalk A: windscreen
wipers
2. Fast wipe.
1. Normal wipe.
Int. Intermittent wipe.0. Park. AUTO Automatic wiping. È
Single wipe: Brief pull on the stalk towards.
Screenwash: Long pull on stalk towards you.
115

Switching on "AUTO" mode
)
Briefly push the stalk downwards.


Switching off "AUTO" mode
)
Briefly push the stalk downwards or place
the stalk in another position: Int, 1 or 2.
Ring B: rear wiper
117
116
Lighting off.
Automatic illumination of headlamps.
Sidelamps.
Dipped / main beam headlamps.
Rear
foglamp.
Park.
Intermittent wipe.
Screenwash.
or
Front and rear
foglamps.

.
19
Familiarisation















































Eco-driving
Eco-driving is a range of everyday practices that allow the motorist to optimise their fuel consumption and CO2 emissions.
Optimise the use of your
gearbox
With a manual gearbox, move off gently, change up without waiting and drive by changing up quite soon. If your vehicle has
the system, the gear shift indicator invites youto change up; it is displayed in the instrumentpanel, follow its instructions.
With an automatic or electronic gearbox, stay in Drive "D"or Auto "A"
, according to the type of gearbox, without pressing theaccelerator pedal heavily or suddenly.
Drive smoothly
Maintain a safe distance between vehicles,use engine braking rather than the brake pedal, and press the accelerator progressively.These practices contribute towards a reductionin fuel consumption and CO2 emissions andalso helps reduce the background traffic noise.
If your vehicle has cruise control, make use of the system at speeds above 25 mph (40 km/h) when the traffic is flowing well.



Control the use of your
electrical equipment
Before moving off, if the passenger compartment is too warm, ventilate it byopening the windows and air vents before using the air conditioning.
Above 30 mph (50 km/h), close the windowsand leave the air vents open. Remember to make use of equipment that canhelp keep the temperature in the passenger compartment down (sunroof and window blinds...).Switch off the air conditioning, unless it has automatic digital regulation, as soon as the desired temperature is attained.Switch off the demisting and defrosting controls, if not automatic.Switch off the heated seat as soon as possible.


Switch off the headlamps and front foglampswhen the level of light does not require their use.

Avoid running the engine before moving off,particularly in winter; your vehicle will warmup much faster while driving.

As a passenger, if you avoid connecting your multimedia devices (film, music, video game...), you will contribute towards limitingthe consumption of electrical energy, and soof fuel.
Disconnect your por table devices beforeleaving the vehicle.

24
Instruments and controls
Operation indicator lamps
If one of the following indicator lamps comes on in the instrument panel and/or instrument panel screen, this confirms that the corresponding system has come into operation.

Warning / indicator lampStateCauseAction / Observations



Left-hand direction indicator
flashing with buzzer. The lighting stalk is pushed down.



Right-hand direction indicator
flashing with buzzer. The lighting stalk is pushed up.
Sidelampsfixed.The lighting stalk is in the
"Sidelamps" position.
Dipped beamheadlampsfixed.The lighting stalk is in the "Dipped
beam headlamps" position.
Main beam headlampsfixed.The lighting stalk is pulled towards
you. Pull the stalk to return to dipped beam headlamps.
Front foglampsfixed.The front foglamps are switched on. Turn the ring on the stalk rear wards twice to switch off
the front foglamps.
Rear foglampfixed.The rear foglamp is switched on. Turn the ring on the stalk rear wards to switch off the
rear foglamp.

For more information on the lighting controls, refer to the "Visibility" section.

106
Visibility














Lighting controls System for selection and control of the various front and rear lamps providing the vehicle's lighting and signalling.
Main lighting
The vehicle has various lamps:
- sidelamps, to be seen,
- dipped beam headlamps to see without
dazzlin
g other drivers,
- main beam headlamps to see clearly when
the road is clear,
- directional headlamps for improved
visibility when cornering.



Additional lighting
Other lamps are installed to fulfil the requirements of particular driving conditions:


- a rear foglamp to better signal the
presence of the vehicle in foggy conditions,

- front foglamps with cornering lighting,

- daytime running lamps to be seen duringthe day,

- guide-me-home and welcome lighting for leaving and entering to the vehicle.


Automatic lighting
functions

Various automatic lighting functions are also
available depending on options:


- guide-me-home lighting,

- cornering lighting,

- welcome lighting,

- daytime running lamps,

- automatic illumination o
f headlamps,

In some weather conditions (e.g. low temperature or humidity), the presence of misting on the internal sur face of theglass of the headlamps and rear lampsis normal; it disappears after the lamps have been on for a few minutes.

108
Visibility
Foglamps selection ring
The foglamps operate with dipped and main beam headlamps.
Front foglamps and rear foglamp
When the headlamps switch off with automatic
illumination of headlamps (AUTO model) or
when the dipped beam headlamps are switched
o
ff manually, the foglamps and sidelamps
remain on. )Turn the ring rear wards to switch off thefoglamps, the sidelamps will then switch off.

Rotate and release the rin
g:)
forwards a first time to switch on the front foglamps,)
forwards a second time to switch on the
rear foglamp,) rearwards a first time to switch off the rear foglamp,)
rearwards a second time to switch of thefront fog lamps.



Rear foglamp only
)To switch it on, turn the ring forwards.
When the lighting is switched off automatically(with AUTO model), the foglamp and the dipped
beam headlamps will remain on.
)To switch it off, turn the ring rearwards.

109
5
Visibility
In good or rainy weather, both dayand night, the front foglamps and the rear foglamp are prohibited. In thesesituations, the power of their beamsmay dazzle other drivers. They shouldonly be used in fog or snow. In these weather conditions, it is your responsibility to switch on the foglamps and dipped beam headlamps manuallyas the sunshine sensor may detect sufficient light.
Do not forget to switch off the front foglamps and the rear foglamp whenthey are no longer necessary.


Switching on the lamps after the ignition isswitched off

To reactivate the lighting control, rotatethe ring to the "0"position - lamps off,then to the desired position. On opening the driver's door a temporary audible signal warns thedriver that the lighting is on.
The lamps, with the exception of thesidelamps, switch off automatically after a maximum duration of thir ty minutes to prevent discharging of the battery.

Switching off the lampswhen the ignition is switched off
On switching off the ignition, all of the lamps turn off immediately, except for dipped beam if guide-me-home lighting is activated.

112
Visibility
The sidelamps and dipped beam headlamps are
switched on automatically, without any action
on the part of the driver, when a low level of external light is detected or in certain cases of activation of the windscreen wipers.
As soon as the brightness returns to a sufficient
level or after the windscreen wipers are switched
o
ff, the lamps are switched off automatically.
Automatic illumination of
headlam
ps
Switching on
)Turn the ring to the "AU TO "position.
Activation of the function is accompanied
b
y a message in the screen.

Switching off
)Turn the ring to another position. Deactivation of the function is accompanied by a message in the screen.



Automatic guide-me-home
lighting
Association with the automatic lighting provides
the guide-me-home lighting with the followingadditional options:


- selection of the lighting duration of 15, 30or 60 seconds,

- automatic activation of guide-me-home lighting when the automatic illumination of
headlamps is in operation.



Operating fault

In the event of a fault with thesunshine sensor, the lighting comes on, this warning lamp
is displayed in the instrument panel and/or a message appears in the screen, accompaniedby an audible signal.
Contact a PEUGEOT dealer or a qualified
workshop.

In fog or snow, the sunshine sensor maydetect sufficient light. In this case, the lighting will not come on automatically. Do not cover the sunshine sensor,coupled with the rain sensor and located in the centre of the windscreenbehind the rear view mirror; theassociated functions would no longer be controlled.


Programming
The duration of the guide-me-home
lighting can be set in the vehicle configuration menu.

114
Visibility
With dipped or main beams, this function makes use of the beam from a front foglamp to
illuminate the inside of a bend, when the vehicle speed is below 25 mph (approximately 40 km/h)(urban driving, winding road, intersections, parking manouevres...).








Cornering lighting
with cornering lighting
without cornering lighting


Switching on

This function starts:


- when the corresponding direction indicator
is switched on,
or

- from a cer tain angle of rotation of the steering wheel.

Programming
The system is activated or deactivated in the vehicleconfiguration menu.The system is activated by default.



Switching off
The system does not operate:


- below a cer tain angle of rotation of thesteering wheel,

- above 25 mph (40 km/h),

- when reverse gear is engaged.

156
Practical information











Changing a bulb


Front lamps
A. Model with light guide

In some weather conditions (e.g. low temperature or humidity), the presence of misting on the internal sur face of theglass of the headlamps and rear lampsis normal; it disappears after the lamps have been on for a few minutes.


The headlamps are fitted with
polycarbonate glass with a protectivecoating:)do not clean them using a dryor abrasive cloth, nor with adetergent or solvent product,)use a sponge and soapy water, )when using a high pressure washer on persistent marks, do not keepthe lance directed towards thelamps or their edges for too long,so as not to damage their protectivecoating and seals,)do not touch the bulb directly withyour fingers, use lint-free cloths.
Changing a bulb should only be doneafter the headlamp has been switched off for a few minutes (risk of seriousburns). It is imperative to use only anti-ultraviolet (UV) type bulbs in order notto damage the headlamp. Always replace a failed bulb with a new bulb with the same type andspecification.
B. Model without light guide
1.Main beam headlamps (H7-55W).2.Dipped beam headlamps (H7-55W).3.Daytime running lamps / sidelamps(light emitting diodes - LEDs).4.Direction indicators (PWY-24W).5.Front foglamps (directional accordingto version) (H11- 55W)).

1.Main beam headlamps (H7-55W).2.Dipped beam headlamps (H7-55W).3.Daytime running lamps / sidelamps (W5-5W).4.Direction indicators (PWY-24W).5.
Front foglamps (directional according
to version) (H11- 55W).