ECO mode Peugeot 208 2013 - RHD (UK, Australia) User Guide

92
Driving
Manual operation
)Select position M for sequentialchanging
o
f the four gears.)Push the lever towards the + sign tochange up a gear. )Pull the lever towards the -
sign to change
down a gear.
It is only possible to change from one gear to another if the vehicle speed and engine speedpermit; otherwise, the gearbox will operate
temporarily in automatic mode.
D disappears and the gears engaged appear in succession in the
instrument panel.

Invalid value duringmanual operation
This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).



Stopping the vehicle

Before switching off the engine, you can engage
position P or N
to place the gearbox in neutral.
In both cases, apply the parking brake to
immobilise the vehicle.

Operating fault
When the ignition is on, the lightingof this warning lamp, accompanied
by an audible signal and a message in the
multifunction screen, indicates a gearbox fault.
In this case, the gearbox switches to back-up mode and is locked in 3rd gear. You may feel
a substantial knock when changing from Pto Rand from N to R
. This will not cause any damage to the gearbox.
Do not exceed 60 mph (10 0 km/h), local speed
restrictions permitting.
Contact a PEUGEOT dealer or a qualified
workshop as soon as possible.
I
f the engine speed is too low or too high, the
gear selected flashes for a few seconds, then
the actual gear engaged is displayed.
It is possible to change from position D(automatic) to position M (manual) at any time.
When the vehicle is stationary or movingvery slowly, the gearbox selects gear M1automatically. The spor t and snow programmes do not
operate in manual mode.

There is a risk of damage to thegearbox:


- if you press the accelerator and brake pedals at the same time,

- if you force the movement of the gear lever from the P
position to another position when the battery is flat.
To reduce fuel consumption when at a prolonged standstill with the engine
running (traffic jam...), put the gear lever in the Nposition and apply the parkingbrake.

If the lever is not in position P
, when the Pdriver's door is opened or approximately 45 seconds after the ignition is switchedoff, a warning message appears in the screen.)Return the lever to position P; the
message disappears.

93
4
Driving











Stop & Start
The Stop & Star t system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...).
The engine restar ts automatically - START mode - as soon as you want to move off. The restar t takes place instantly, quickly and silently.
Per fect for urban use, the Stop & Star t system reduces fuel consumption and exhaust emissions as well as the noise level when stationary.


Operation


Going into engine STOP mode
The "ECO"warning lamp comes
on in the instrument panel and the
engine goes into standby:


-
with a manual gearbox
, at speeds below
12 mph (20 km/h), when you put the gear
lever into neutral, and you release theclutch pedal.
-withanelectronic gearbox , at speeds
below 5 mph (8 km/h), when you press the
brake pedal or put the gear lever inposition N
.


Never refuel with the engine in STOPmode; you must switch off the ignition with the key.
For your comfort, during parking manoeuvres, STOP mode is not available for a few seconds after coming out of reverse gear.STOP mode does not affect the functionality of the vehicle, such as for example, braking, power steering...


Special cases: STOP mode notavailable
STOP mode is not invoked when:


- the driver's door is open,

- the driver's seat belt is not fastened,

- the vehicle has not exceeded 6 mph (10 km/h) since the last engine star t using
the key,

- the engine is needed to maintain acomfor table temperature in the passenger compartment,

- demisting is active,

- some special conditions (battery charge, engine temperature, braking assistance,
ambient temperature...) where the engine isneeded to assure control of a system.

A time counter calculates the sum
of the periods in STOP mode
during a journey. It rests itself
to zero every time the ignition is switched on with the key.
The "ECO"
warning lamp flashes for a few seconds then goes off.
This operation is perfectl
y normal.

94
Driving
mode
The "ECO"warning lamp goes off
and the engine starts:
- with a manual gearbox
, when you
depress the clutch pedal,
- with an electronic
gearbox
:
●
gear lever in position Aor M
, when yourelease the brake pedal,
●
or gear lever in position Nand the brakepedal released, when you move the gear lever to position A
or M
,
●
or when you engage reverse gear. For reasons of safet
y and for your comfort,START mode is invoked automatically when:


Special cases: START invoked
automatically


- you open the driver's door,

- you unfasten the driver's seat belt,

- the speed of the vehicle exceeds 7 mph(11 k m / h) with an electronic gearbox,

- some special conditions (battery charge,engine temperature, braking assistance,
ambient temperature...) where the engine is
needed for control of a system.


If the system has been deactivatedin STOP mode, the engine restartsimmediately.

At any time, press the "ECO OFF"
switch todeactivate the system.
This is confirmed by the switch warning lampcoming on accompanied by a message in the screen.


Deactivation
The "ECO"
warning lamp flashes for
a few seconds, then goes off.
This operation is per fectly normal.

95
4
Driving
The system is reactivated automatically at every new star t using the key.


Reactivation

Press the "ECO OFF"switch again.
The s
ystem is active again; this is confirmed
by the switch warning lamp going off,
accompanied by a message in the screen.
Operating fault
In the event of a fault with the system,
the "ECO OFF"switch warning lamp flashes
then comes on continuously.
Have it checked by a PEUGEOT dealer or aqualified workshop.
In the event of a fault in STOP mode, the
vehicle ma
y stall. All of the warning lamps come on. It is then necessary to switch off
the ignition and star t the engine again using
the key.

Before doing anything under the bonnet,deactivate the Stop & Start system toavoid any risk of injury resulting fromautomatic operation of STA R T m o d e .

This s
ystem requires a battery with a specialspecification and technology (reference
numbers available from a PEUGEOT dealer or
a qualified workshop).
Fitting a battery not listed byPEUGEOT introduces the risk of malfunction of
the system.



Maintenance

The Stop & Start system makes use of advanced technology. All work onthis type of battery must be done by a PEUGEOT dealer or a qualifiedworkshop.

98
Driving
) Turn thumb wheel 1to the "LIMIT"position: the speed limiter mode
is selected but is not switched on(PAUSE).
You do not have to switch the speed limiter
on in order to set the speed.
Programming

On a steep descent or in the event of sharp acceleration, the speed limiter willnot be able to prevent the vehicle from exceeding the programmed speed.
To a v o i d a ny risk of jamming of the pedals:


- ensure that the mat is positioned correctly,

- do not fit one mat on top of another.




Leaving limiter mode

Operatin
g fault
)Set the speed value by pressing button 2or 3.You can then change the programmed speed using buttons 2
and 3:- by + or - 1 mph (km/h) = shor t press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press.

Exceeding the programmed speed
)Switch the speed limiter back on by pressing button 4
again.


)Switch the speed limiter on by pressing button 4 .
)Switch the speed limiter off by pressing button 4: the display confirms that it has been switched off (PAUSE). In the event of a speed limiter fault, the speed
is cleared resultin
g in flashing of the dashes.
Have it checked by a PEUGEOT dealer or a qualified workshop.
)Turn thumb wheel 1
to the "0"position:
the speed limiter mode is deselected. The
displa
y returns to the distance recorder.
Pressing the accelerator pedal to exceed the programmed speed will not have
any effect unless you press the pedal firmlypast the ypoint of resistance.eThe speed limiter is deactivated temporarily and the programmed speed, which
is still displayed, flashes.
Returning to the programmed speed, by means of intentional or unintentional
deceleration of the vehicle, automatically cancels the flashing of the
programmed speed.

99
4
Driving




Cruise control
speed of the vehicle at the value programmed
by the driver, without any action on the
accelerator pedal.

Th
e cruise control is switched off
manually for by pressing the brake or clutch pedal or on
triggering of the electronic stability system for safety reasons.
It is possible to exceed the programmed speed
temporarily by pressing the accelerator pedal.
To return to the programmed speed, simply
release the accelerator pedal.
Switching off the ignition cancels any programmed speed value.
1
.Selection of cruise control mode.
2. Cruise control stop/resume.
Steering mounted controls

The cruise control cannot, in any circumstances,replace the need to respect speed limits, nor canit replace the need for vigilance and responsibilityon the par t of the driver.


The programmed information is grouped
together in the instrument panel screen.
5.Cruise control stopped/resumed indication.
6. Cruise control mode selection indication.
7. Programmed speed value.8. Selecting a memorised speed setting.


Displays in the instrument panel
3.
Increase the programmed value. 4.
Decrease the programmed value. Th
e cruise control is switched on
manually: it
requires a minimum vehicle speed of 25 mph (40 km/h), as well as the engagement of:


- fourth gear on a manual gearbox,

- second gear on an electronic or automatic
gearbox, in manual sequential mode,

- position A
on an electronic gearbox or position D
on an automatic gearbox.

100
Driving
) Turn thumb wheel 1to the "CRUISE"position: the cruise control mode
is selected but is not switched on(PAUSE).

Programming
You can then change the programmed speed using buttons 2
and 3:- by + or - 1 mph (km/h) = shor t press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press.

Intentional or unintentional exceedin
g of the programmed speed results
in flashing of this speed in the screen.
Return to the programmed speed, by means of intentional or
unintentional deceleration of the vehicle, automatically cancels theflashing of the speed.
When the cruise control is switched on,be careful if you maintain the pressure on one of the programmed speedchanging buttons: this may result in avery rapid change in the speed of your vehicle.
Do not use the cruise control on slippery roads or in heavy traffic. On a steep descent, the cruise controlwill not be able to prevent the vehicle from exceeding the programmed speed.
To avoid any risk of jamming of the pedals:


- ensure that the mat is positioned correctly,

- never fit one mat on top of another.




Operating fault
Leavin
g cruise control mode
)Turn thumb wheel 1 to the "0"position: the cruise control mode isdeselected. The display returns to the distance recorder.

Exceeding the programmed speed
)Set the programmed speed byaccelerating to the required speed, then press button 2or 3.
)Switch off the cruise control by pressing button 4
: the screenconfirms that it has been switched off (PAUSE).
)Switch the cruise control back on by pressing button 4again. In the event o
f a cruise control malfunction,
the speed is cleared resulting in flashing of the
dashes. Have it checked by a PEUGEOT dealer
or a qualified workshop.

112
Visibility
Foglamps selection ring
The foglamps operate with dipped and main beam headlamps.
Front foglamps and rear foglamp
When the headlamps switch off with automatic
illumination of headlamps (AUTO model) or
when the dipped beam headlamps are switched
o
ff manually, the foglamps and sidelamps
remain on. )Turn the ring rear wards to switch off thefoglamps, the sidelamps will then switch off.

Rotate and release the rin
g:)
forwards a first time to switch on the front foglamps,)
forwards a second time to switch on the
rear foglamp,) rearwards a first time to switch off the rear foglamp,)
rearwards a second time to switch of thefront fog lamps.



Rear foglamp only
)To switch it on, turn the ring forwards.
When the lighting is switched off automatically(with AUTO model), the foglamp and the dipped
beam headlamps will remain on.
)To switch it off, turn the ring rearwards.

114
Visibility
Daytime running lamps
Daytime lighting, compulsory in cer tain
countries, which comes on automatically when
the engine is star ted making the vehicle more
visible to other users.
LED lamps
They come on when the engine is star ted.
Depending on the country of sale, they are used for:
- daytime running lamps * in day mode and
sidelamps in night mode (they are brighter
when daytime running lamps), or
- sidelamps in day and night mode.

*

Function that can be set in the vehicleconfiguration menu.
Thi
s function is assured:


- in countries where it is imposed by
re
gulations,
by illumination of the dipped beam
headlamps with the sidelamps and number
plate lamps; this function cannot be
deactivated.

- for other countries where it is provided,
by the use of dedicated lamps (bulbs or
LEDs); this function can be activated or
deactivated via the vehicle configurationmenu.
The lighting control stalk must be placed in
th
e "0"
or "AUTO"
(day mode) position.
Deactivation of the daytime running lamps iseffective after operation of the lighting control
stalk or after the next engine start; activation iseffective immediately.

The instruments and controls
(instrument
panel, multifunction screen, air conditioning control panel, ...) are not illuminated, except
in night mode with manual or automatic
illumination of headlamps.

123
5
Visibility











Courtesy lamp
In this position, the cour tesy lamp comes on gradually:


Take care to avoid leaving anything in contact with the courtesy lamp. - when the vehicle is unlocked,
- when the ke
y is removed from the ignition,
- when opening a door,
- when the remote control locking button is
pressed, in order to locate your vehicle.
It switches o
ff gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- 30 seconds after the last door is closed.
Permanentl
y off.
Permanent lighting.
) With the ignition on, press
the corresponding switch.



1. Front cour tes
y lamp

2. Map reading lamp s
With the "permanent lighting" mode,the lighting time varies according to the circumstances:



- with the ignition off, approximately ten minutes,

- in energy economy mode, approximatelythirty seconds,-with the engine running, unlimited.



Front map reading lamps