battery Peugeot 208 2017 User Guide

77
If you benefit from the Peugeot Connect
Packs offer with the SOS and assistance
pack included, there are additional
ser vices available to you in your personal
space, via the Internet website for your
c o u nt r y.
Peugeot Connect
Assistance
** As per the geographic coverage of "Peugeot Connect SOS", "Peugeot Connect
Assistance" and the official national
language chosen by the owner of the vehicle.
T

he list of countries covered and PEUGEOT
CONNECT services is available from dealers
or at www.peugeot.co.uk.
Press this button for more than
2

seconds to request assistance
if the vehicle breaks down.
A voice message confirms that the call has
been made**. Pressing this button again
immediately cancels the
request.
The cancellation is confirmed by a voice
message.
Geo-location
You can deactivate geo-location by
simultaneously pressing the "Peugeot Connect
SOS" and "Peugeot Connect Assistance"
buttons, followed by a press on "Peugeot
Connect Assistance" to confirm.
To reactivate geo-location, simultaneously
press the "Peugeot Connect SOS" and
"Peugeot Connect Assistance" buttons again,
followed by a press on "Peugeot Connect
Assistance" to confirm.
Operation of the system
When the ignition is switched
on, the green indicator lamp
comes on for 3
seconds
indicating that the system is
operating correctly.
The orange indicator lamp
flashes then goes off: the
system has a fault.
The orange indicator lamp is permanently on:
the back-up battery should be replaced. The system's fault does not prevent the
vehicle from being driven.
In both cases, the emergency and assistance
calls ser vice may not work.
Contact a qualified repairer as soon as
possible.
5
Safety

113
Manual mode
This mode allows manual sequential gear
changing.
F
M
ove the selector lever to M .
F

P
ush the lever for ward to change
up.
F

P
ull the lever back to change
down.
Steering mounted control paddles
F Pull the "+" paddle to change up.
F P ull the "-" paddle to change up.
The gear engaged is indicated in the display.
Creep function
Depending on the engine, the vehicle moves
without pressing the accelerator.
Assistance with low-speed
manoeuvres
With the engine running at idle, parking brake
released and the lever placed at A , M or R, the
vehicle moves off when your release the brake
pedal.
It stops on opening the driver's door. Closing
the door, and putting your foot on the brake
or accelerator pedal allows movement of the
vehicle again. Following disconnection of the battery, you
have to reinitialise the gearbox.
F

S
witch on the ignition.
AUTO and – appear in the
instrument panel.
F
Sel
ect position N
.
F
P
ress the brake pedal firmly.
F
W
ait around 30 seconds until N or a gear
appears in the instrument panel.
F
R
elease the brake pedal.
The gearbox is operational again.
With the ignition on, if this warning
lamp comes on and AUTO flashes,
accompanied by an audible signal
and a message in the screen, this
indicates a gearbox fault.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
6
Driving

116
If the lever is not in position P, a message
appears in the screen on opening the
driver's door or approximately 45
seconds
after switching off the ignition.
F

P
lace the lever at position P ; the
message disappears.
When driving on flooded roads or when
crossing a ford, proceed at walking pace.
When the ignition is on, the lighting
of this warning lamp, associated with
an audible signal and a message
on the screen, indicates a gearbox
fault.
In this case, the gearbox switches to back-up
mode and is locked in 3rd gear. You may feel
a substantial knock when changing from P
to R and from N to R. This will not cause any
damage to the gearbox.
Do not exceed 60
mph (100 km/h), local speed
restrictions permitting.
Contact a PEUGEOT dealer or a qualified
workshop as soon as possible. There is a risk of damage to the gearbox:
F
i f you press the accelerator and brake
pedals at the same time,
F

i
f you force the movement of the lever
from position P to another position with
a flat battery.
To reduce fuel consumption during
prolonged stops with the engine running
(traffic jams, etc.), position the gear lever
at N and apply the parking brake.Gear shift indicator
(Depending on engine.)
This system reduces fuel consumption by
recommending the most appropriate gear.
Depending on the driving situation and your
vehicle's equipment, the system may advise
you to skip one (or more) gear(s). You can
follow this instruction without engaging the
intermediate gears.
Gearshift recommendations should not be
considered obligatory. The configuration of the
road, the amount of traffic and safety remain
determining factors when choosing the best
gear. The driver thus remains responsible
for deciding whether to follow or ignore the
system's instructions.
This function cannot be deactivated.
With an electronic or automatic gearbox,
the system is only active in manual mode.
Driving

119
With BlueHDi Diesel and a manual gearbox:
- A s soon as the vehicle stops or the speed is
less than 2
mph (3 km/h) (with 1.5 Blue HDi
engine).
-

G
ear lever in neutral and clutch pedal
released.
With PureTech petrol and a manual,
electronic or automatic gearbox :
-

A
s soon as the vehicle stops or the speed
is less than 2
mph (3 km/h) (with manual
gearbox and depending on which version
you have).
-

G
ear lever in neutral and clutch pedal
released (manual gearbox).
-

B
rake pedal pressed or gear lever in
position N (electronic or automatic gearbox).
Special cases: STOP mode not
available
STOP mode is not invoked when:
- t he driver's door is open,
-

t
he driver's seat belt is not fastened,
-

t
he vehicle has not exceeded 6 mph
(10
km/h) since the last engine start using
t h e key,
-

t
he engine is needed to maintain a
comfortable temperature in the passenger
compartment,
-

d
emisting is active, The ECO warning lamp flashes for a
few seconds, then goes off.
This operation is perfectly normal.
A time counter sums up the time
periods spent in STOP mode
during a journey. It resets every
time the ignition is switched on
using the key.
For your comfort, during parking
manoeuvres, STOP mode is not available
for a few seconds after coming out of
reverse gear.
The Stop & Start system does not affect
the functionality of the vehicle, such as for
example, braking, power steering, With a manual gearbox in STOP mode, if
a gear is engaged without fully depressing
the clutch pedal, a warning lamp comes
on or an alert message is displayed asking
you to depress the clutch pedal to restart
the engine.
Never refuel with the engine in STOP
mode; you must switch off the ignition
using the key.
START mode
The ECO warning lamp goes off and
the engine starts:
With a manual gearbox :
-

C

lutch pedal depressed.
With an electronic / automatic gearbox :
-

G

ear lever in position A / D or M .
-
B

rake pedal released.
or
-
s

ome special conditions (battery charge,
engine temperature, braking assistance,
exterior temperature, etc.) where the engine
is needed to control the system.
6
Driving

120
- Gear lever in position N.
- Brake pedal released.
-

T
hen gear lever in position A / D or M .
or
-
R

everse gear engaged.
Special cases: START invoked
automatically
As a safety measure and for your comfort,
START mode is invoked automatically when:
-
y
ou open the driver's door,
-
y

ou unfasten the driver's seat belt,
-
s

ome special conditions (battery charge,
engine temperature, braking assistance,
air conditioning setting, etc.) where the
engine is needed for control of the system
or vehicle.
The ECO warning lamp flashes for a
few seconds, then goes off.
This operation is perfectly normal.
Manual deactivation
In certain circumstances, such as the need
to maintain a comfortable temperature in the
passenger compartment, it may be preferable
to deactivate the Stop & Start system.
The system can be deactivated at any time,
once the ignition is switched on.
This control switches off the Stop & Start
system.
-
Press.
-

T
he indicator lamp in the control remains
on.
-

A m
essage is displayed.
If you are stationary in Stop mode, the engine
restarts immediately.
Manual reactivation
- Press.
- T he indicator lamp in the control goes off.
-

A c
onfirmation message is displayed. If the engine is in STOP mode, it restarts
immediately.
The Stop & Start system is reactivated
automatically every time the ignition is
switched on.
Opening the bonnet
Before doing anything under the bonnet,
deactivate the Stop & Start system to
avoid the risk of injury related to an
automatic change to START mode.
Driving on flooded roads
Before driving in a flooded area, it is
strongly recommended that you deactivate
the Stop & Start system.
For more information on Driving advice
,
particularly on flooded roads, refer to the
corresponding section.
Driving

121
Operating fault
In the event of a fault with the system, the ECO
OFF switch warning lamp flashes then comes
on fixed.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
If a fault occurs in STOP mode, the vehicle
may stall. All of the instrument panel warning
lamps come on. It is then necessary to switch
the ignition off and to restart the engine using
t h e key.The Stop & Start system requires a
12
V battery of specific technology and
specification.
All work on this type of battery must be
carried out only by a PEUGEOT dealer or
a qualified workshop.
For more information on the 12
V batter y,
refer to the corresponding section.
Speed limiter "LIMIT"
The system prevents the vehicle from
exceeding the speed setting programmed by
the driver.
Steering mounted controls
1. Speed limiter mode selection / off.
2. Increases the set value.
3. Decreases the set value.
4. Speed limiter On / Pause. The vehicle responds to the accelerator until
resistance is felt in the pedal, which signifies
that the vehicle has reached the limiter speed
setting.
However, pressing the pedal beyond this point
of resistance to the floor permits exceeding
of the programmed speed. To resume use of
the limiter, simply reduce the pressure on the
accelerator pedal gradually and return to a
speed below that programmed.
Setting and operation of the system can be
done stationar y with the engine running or
when driving.
Selection
F Place the thumbwheel at the "LIMIT"

position: the speed limiter mode is selected
but is not switched on (PAUSE).
Switching the speed limiter on is not required to
set the speed limit.
The speed setting is selected with the engine
running, stationary or when driving. The
minimum speed setting possible is 20

mph
(30


km/h).
6
Driving

143
Load reduction mode
System which manages the use of certain
functions according to the level of charge
remaining in the battery.
When the vehicle is being driven, the load
reduction function temporarily deactivates
certain functions, such as air conditioning,
heated rear screen, etc.
The deactivated functions are reactivated
automatically as soon as conditions permit.
Energy economy mode
System which manages the duration of use of
certain functions to conser ve a sufficient level
of charge in the battery.
After the engine has stopped, you can still use
functions such as the audio and telematics
system, windscreen wipers, dipped beam
headlamps, courtesy lamps, etc. for a
maximum combined duration of about forty
minutes.
Switching to this mode
A message appears in the instrument panel
screen indicating that the vehicle has switched
to economy mode and the active functions are
put on standby.If a telephone call is being made at this
time, it will be maintained for around
10
minutes with the Bluetooth hands-free
system of your audio system.
Exiting the mode
These functions will be automatically restored
the next time the vehicle is used. A flat battery prevents the engine from
starting.
For more information on the 12
V batter y
,
refer to the corresponding section.
In order to restore the use of these functions
immediately, start the engine and let it run:
-
f
or less than ten minutes, to use the
equipment for approximately five minutes,
-
f
or more than ten minutes, to use the
equipment for up to approximately thirty
minutes.
Let the engine run for the duration specified to
ensure that the battery charge is sufficient.
Do not repeatedly and continuously restart the
engine in order to charge the battery.
7
Practical information

147
Engines
Petrol
Diesel
These engines are examples provided as a
guide.
The positions of the following elements may
change:
-
A
ir filter.
-

E
ngine oil dipstick.
-

E
ngine oil filler cap.
-
P

riming pump.
1. Screenwash fluid reservoir.
2. Engine coolant reservoir.
3. Brake fluid tank.
4. Battery.
5. Fusebox.
6. A i r f i l t e r.
7. Engine oil dipstick.
8. Engine oil filler cap.
9. Priming pump*.
The Diesel circuit is under very high
pressure.
All work on this circuit must be carried out
only by a PEUGEOT dealer or a qualified
workshop.
*
D

epending on engine.
7
Practical information

150
Screenwash fluid level
Top up to the required level when
necessary.
Fluid specification
The screenwash fluid must be topped up with a
ready for use mix.
In winter (temperatures below zero), a liquid
with antifreeze must be used that is appropriate
for the prevailing conditions, in order to
preser ve the elements of the system (pump,
tank, ducts, etc.).
Filling with pure water is prohibited under all
circumstances (risk of freezing, limestone
deposits, etc.).
Diesel fuel additive level
(Diesel with particle filter)
The additive reser voir low level is
indicated by fixed illumination of this
warning lamp, accompanied by an
audible signal and a message that
the particle filter additive level is
too low.
To p p i n g u p
The reser voir must be topped up without delay
by a PEUGEOT dealer or a qualified workshop.
Level of AdBlue
An alert is triggered once the reser ve level is
reached.
To avoid the vehicle being immobilised as per
regulations, you must top up with AdBlue.
For more information on AdBlue
® and the SCR
system, and in particular topping it up, refer to
the corresponding section.
Checks
Unless otherwise indicated, check these
components in accordance with the
manufacturer's service schedule and according
to your engine.
Other wise, have them checked by a PEUGEOT
dealer or a qualified workshop.
12 V battery
The battery does not require any
maintenance.
However, check regularly that the
terminals are correctly tightened
(versions without quick release terminals)
and that the connections are clean.
For more information and the precautions
to take before starting work on the 12 V
battery , refer to the corresponding
section.
Versions equipped with Stop & Start are
fitted with a 12
V lead-acid battery of
specific technology and specification.
Its replacement should be carried out
only by a PEUGEOT dealer or a qualified
workshop.
Practical information

177
Underbonnet
The fusebox is placed in the engine
compartment near the battery (left-hand side).
Access to the fuses
F Unclip the cover.
F C hange the fuse.
F

W
hen you have finished, close the cover
very carefully to ensure correct sealing of
the fusebox. Fuse no.
Rating Functions
F16 15 AFront foglamps.
F18 10 ARight-hand main beam headlamp.
F19 10 ALeft-hand main beam headlamp.
F25 30 AHeadlamp washer relay (after-market).
F26 (GPL) 20 ABattery + (positive).
F29 40 AFront wiper motor.
8
In the event of a breakdown