ECU Peugeot 208 2018 User Guide

78
Advice
The incorrect installation of a child seat in
a vehicle compromises the protection of
the child in the event of an accident.
Ensure that there is no seat belt or seat
belt buckle under the child seat, as this
could destabilise it.
Remember to fasten the seat belts or
the child seat harness keeping the slack
relative to the child's body to a
minimum,
even for short journeys.
When installing a


child seat using the seat
belt, ensure that the seat belt is tightened
correctly on the child seat and that it
secures the child seat firmly on the seat
of your vehicle. If your passenger seat is
adjustable, move it forwards if necessary.
The head restraint must be removed
before installing a
child seat with
a
backrest on a passenger seat.
Ensure that the head restraint is stored or
attached securely to prevent it from being
thrown around the vehicle in the event
of sharp braking. Refit the head restraint
when the child seat is removed. Children at the rear
At rear seating positions, always leave
sufficient space between the front seat
and:
-

a "
rear ward facing" child seat,
-

t
he child's feet for a child seat fitted
"forward facing".
To do this, move the front seat for wards
and, if necessary, straighten its backrest.
For optimal installation of the "forward
facing" child seat, verify that its backrest is
as close as possible to the backrest of the
vehicle seat, if possible in contact with it.
Children at the front
The legislation on carrying children on the
front passenger seat is specific to each
country. Refer to the legislation in force in
the country in which you are driving.
Deactivate the front passenger airbag
when a "rear ward facing" child seat is
installed on the front passenger seat.
Other wise, there is a
risk of serious or
fatal injury to the child if the airbag is
deployed. Installing a


booster seat
The chest part of the seat belt must be
positioned on the child's shoulder without
touching the neck.
Ensure that the lap part of the seat belt
passes correctly over the child's thighs.
We recommend using a
booster seat with
a
backrest, equipped with a belt guide at
shoulder level.
Additional protections
To prevent accidental opening of the doors
and rear windows, use the child lock.
Take care not to open the rear windows by
more than one third.
To protect young children from the rays
of the sun, fit side blinds on the rear
windows.
As a
safety precaution, do not leave:
-

a c
hild or children alone and
unattended in a
vehicle,
-

a c
hild or an animal in a vehicle
which is exposed to the sun, with the
windows closed,
-

t
he keys within reach of children inside
the vehicle.
Safety

93
Malfunction
The registered speed is erased, then replaced
by three dashes.
Have it checked by a PEUGEOT dealer or
a


qualified workshop. Under no circumstances can the speed
limiter replace the need to obser ve speed
limits, nor the need for vigilance on the
part of the driver.
Always pay attention to the profile of the
road, be careful when accelerating sharply
and stay in complete control of your
vehicle.
To avoid any jamming under the pedals:
-

e
nsure that the mat is positioned and
secured to the floor correctly,
-

n
ever fit one mat on top of another.
Cruise control "CRUISE"
System which automatically maintains the
speed of the vehicle at the value programmed
by the driver, without any action on the
accelerator pedal.
Steering mounted controls
1.Cruise control mode selection/off.
2. Increase the programmed value.
3. Decrease the programmed value.
4. Stop/resume cruise control.
This driving assistance system, for use
when the traffic is flowing, allows a
speed
programmed by the driver to be maintained,
except on a
steep gradient.
With a
manual gearbox
In order for it to be programmed or activated,
the speed of the vehicle must be above 25
mph
(40
km/h) with 4
th gear or higher engaged.
With an automatic gearbox
In order for it to be programmed or activated,
the speed of the vehicle must be above 25
mph
Selection
(40 km/h) with 2nd gear or higher engaged in
manual mode, or position D selected.
F

P

lace the thumbwheel at the " CRUISE"
position: cruise control mode is selected,
but is not switched on (PAUSE).
Registering a cruise speed
se tting
- Bring the vehicle up to the desired speed by
pressing the accelerator.
-

P
ress the SET – or
SET + button.
The speed setting is registered/activated and
the vehicle will maintain this speed.
6
Driving

95
A short press decreases the setting by 1 mph
( km/h).
Pressing and holding decreases the setting in
steps of 5
mph (km/h).
Switching the function off
F Place the thumbwheel at the " 0" position:
cruise control mode is deselected. The
display returns to the total mileage recorder.
After switching off the ignition, all registered
speed settings are lost.
Malfunction
The registered speed is erased, then replaced
by three dashes.
Have it checked by a
PEUGEOT dealer or
a


qualified workshop. When changing the registered speed
setting by means of a
maintained press,
pay attention as the speed may increase
or decrease rapidly.
Do not use the cruise control on slippery
roads or in heavy traffic.
On a steep descent, the cruise control will
not be able to prevent the vehicle from
exceeding the registered speed.
The cruise control system cannot, in
any circumstances, replace the need
to obser ve speed limits or the need for
vigilance on the part of the driver.
To avoid any risk of jamming of the pedals:
-
e
nsure that the mat is positioned and
secured to the floor correctly,
-
n
ever fit one mat on top of another.
Memorising speeds
This function allows speed settings to be stored
that will then be offered for configuration of two
systems: speed limiter (limit speed) or cruise
control (cruise speed).
You can memorise up to five speed settings in
With touch screen
This memorisation can be
configured from the Driving/Vehicle

menu.
F

Sel

ect the " Driving functions " tab.
F

Sel

ect the " Adjusting speeds " function.
F

P

ress " ON" to activate the function.
F

T

ick the speed settings 1 to 5 that you want
to use.
F

S

elect the speed setting value that you want
to change.
F

E

nter the new value using the numerical
keypad and press " OK" to confirm.
As a

safety measure, the driver must carry
out these operations when stationary.
the system for each of the two systems.
By default, some speed settings are already
memorised.
6
Driving

111
Recommendations
Distribute the load evenly, making sure not
to overload one of the sides.
Arrange the heaviest part of the load as
close as possible to the roof.
Secure the load firmly.
Drive gently: the vehicle will be more
susceptible to the effects of side winds
and its stability may be affected.
On a long journey, check the security of
the load at every stop.
Remove the roof bars when they are not
in use.
Bonnet
The location of the interior bonnet release
lever prevents opening of the bonnet when
the left-hand front door is shut. When the engine is hot, handle the
exterior safety catch and the stay with
care (risk of burns), using the protected
area.
When the bonnet is open, take care not to
damage the safety catch.
Do not open the bonnet under very windy
conditions.
The cooling fan may star t after
switching off the engine: take care
with articles and clothing that might be
caught by the fan blades.
Because of the presence of electrical
equipment under the bonnet, it is
recommended that exposure to water
(rain, washing, etc.) be limited.
Opening
F Open the left-hand front door.
F
P
ull the release lever A
, located at the
bottom of the door frame, towards you.
F
L
ift the safety catch B and raise the bonnet.
F
U
nclip the stay C from its housing and place
it in the support slot to hold the bonnet
open.
Closing
F Take the stay C out of its support slot.
F C lip the stay in its housing.
F

L
ower the bonnet and release it near the
end of its travel.
F

P
ull on the bonnet to check that it is fully
latched.
Before doing anything under the bonnet,
deactivate the Stop & Start system to
avoid the risk of injury related to an
automatic change to START mode.
7
Practical information

122
Temporary puncture
repair kit
Scan the QR code on page 3 to view
e xplanatory videos.
Comprising a
compressor and a sealant
cartridge, it allows the temporary repair of
a

tyre so that you can drive to the nearest
garage.
It is designed to repair most punctures which
could affect the tyre, located on the tyre tread
or shoulder.
Access to the kit
This kit is installed in the under floor storage,
under the boot floor. The vehicle's electric system allows the
connection of the compressor for long
enough to inflate a
tyre after a puncture
repair.
Composition of the kit
1. 12 V compressor, with integral pressure
gauge.
2. Sealant cartridge bottle, with integral hose.
3. Speed limit sticker.
Repair procedure
F Park the vehicle without obstructing any
traffic and apply the parking brake.
F

F
ollow the safety instructions (hazard
warning lamps, warning triangle, wearing
high visibility vest, etc.) according to the
legislation in force in the country where you
are driving.
F

S
witch off the ignition. F

U
ncoil the pipe stowed under the
compressor.
Avoid removing any foreign bodies which
have penetrated into the tyre.
F
C
onnect the pipe from the compressor to
the bottle of sealant.
F
T
urn the sealant bottle over and secure it in
the notch provided on the compressor.
In the event of a breakdown

123
F Remove the valve cap from the tyre to be repaired, and place it in a clean area.
F

C
heck that the compressor switch is at the
" O " position.
F

U
ncoil fully the electric cable, stowed under
the compressor.
F

C
onnect the compressor's electric plug to
the vehicle's 12
V socket.
F

A
ffix the speed limit sticker.
The speed limit sticker must be secured
to the interior of the vehicle in the driver's
field of vision, to remind you that a
wheel
is in temporary use. F

S
witch on the ignition.
If a
pressure of 2 bars is not reached after
about 7
minutes, this indicates that the
tyre is not repairable; contact a
PEUGEOT
dealer or a
qualified workshop for
assistance.
F

C
onnect the hose from the bottle of sealant
to the valve of the tyre to be repaired and
tighten firmly. The tyre inflation pressures are given on
this label.
F

S
tart the compressor by turning the switch
to the " l" position until the pressure of the
tyre reaches 2.0
bars. The sealant product
is injected under pressure into the tyre;
do not disconnect the pipe from the valve
during this operation (risk of blowback). F
P lace the switch in the "
O" position.
F D isconnect the compressor's electric plug
from the vehicle's 12
V socket.
F

R
eplace the cap on the valve.
F

R
emove the kit.
F

R
emove and then store the bottle of sealant.
Take care, the sealant product is harmful
if swallowed and causes irritation to the
eyes.
Keep this product out of the reach of
children.
The use-by date of the fluid is marked on
the bottle.
After use, do not discard the bottle in
standard waste, take it to a
PEUGEOT
dealer or an authorised waste disposal
site.
Do not forget to obtain a
new bottle of
sealant, available from a
PEUGEOT
dealer or a
qualified workshop.
8
In the event of a breakdown

125
Do not drive more than 125 miles (200 km)
w ith the repaired tyre; see a PEUGEOT
dealer or a
qualified workshop to change
the tyre.
Under-inflation detection
Should the pressure of one or more tyres
be adjusted, it is necessary to reinitialise
the under-inflation detection system.
For more information on Under-inflation
detection , refer to the corresponding
section. After a
tyre repair, this warning
lamp will remain on until the
system is reinitialised.
For more information on Under-inflation
detection , refer to the corresponding
section.Spare wheel
Scan the QR code on page 3 to view
e xplanatory videos.
Procedure for changing a


damaged wheel with
the spare wheel using the tools provided with
the vehicle.
Access to the tools List of tools
1.
Wheelbrace.
For removing the wheel trim and removing
the wheel fixing bolts.
2. Jack with integrated handle.
Used to raise the vehicle.
3. Bolt "cover" tool.
For removing the bolt protectors (covers)
on alloy wheels.
4. Socket for the security bolts.
For adapting the wheelbrace to the special
"security" bolts.
5. Towing eye.
For more information on To w i n g , refer to
the corresponding section.
The tools are installed in the boot under the
f l o o r.
To gain access:
F

o

pen the boot,
F

l

ift the floor and remove it,
F

r

emove the carrier box containing the tools.
8
In the event of a breakdown

127
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not
block traffic: the ground must be level,
stable and non-slippery.
Apply the parking brake.
Switch off the ignition.
With a

manual gearbox, engage first gear
to block the wheels.
With an automatic gearbox, place the
lever in position P to block the wheels.
Check for the fixed illumination of the
parking brake indicator lamps in the
instrument panel.
The occupants must get out of the vehicle
and wait where they are safe.
Never go underneath a
vehicle raised
using a
jack; use an axle stand.
List of operations
F Place the foot of the jack 2 on the ground
and ensure that it is directly below the front
A or rear B jacking point provided on the
underbody, whichever is closest to the
wheel to be changed.
F Remove the bolt cover from each of the bolts using the tool 3 (depending on equipment).
F

F
it the security socket 4 on the wheelbrace
1
to slacken the security bolt (depending on
equipment).
F

S
lacken the other bolts using the
wheelbrace 1
o n l y.
Ensure that the jack is stable on a sur face
t hat is not loose or slippery and positioned
strictly at jacking points A or B under the
vehicle, making sure that the jack head is
centred at the contact point on the vehicle.
Other wise, there is a
risk of damage to
the vehicle and/or of the jack collapsing or
slipping – risk of injury!
F Extend the jack 2 until its head comes
into contact with the jacking point A or B ,
whichever is used; the contact area A or B
on the vehicle must be correctly inserted into
the central part of the head of the jack.
F

Ra
ise the vehicle until there is sufficient
space between the wheel and the ground to
admit the spare (not punctured) wheel easily.
F Remove the bolts and store them in a clean
place.
F

R
emove the wheel.
8
In the event of a breakdown

128
Fitting the wheelList of operations
Fitting a steel or "s pace-saver" spare
wheel
If your vehicle is fitted with alloy wheels,
when tightening the bolts on fitting it is
normal to notice that the washers do not
come into contact with the steel or "space-
saver" spare wheel. The wheel is secured
by the conical contact of each bolt.
F Put the wheel in place on the hub.
F S crew in the bolts by hand as far as possible.
F

P
re-tighten the security bolt using
wheelbrace 1
fitted with security socket
4
(depending on equipment).
F

P
re-tighten the other bolts using wheelbrace
1
o n l y.
F Lower the vehicle again fully.
F F old jack 2 and remove it. F

T
ighten the security bolt using wheelbrace
1 fitted with security socket 4 (depending on
equipment).
F
T
ighten the other bolts using wheelbrace
1 o n l y.
F
R
efit the bolt covers on each of the bolts
(depending on equipment).
F
S
tore the tools in the carrier box.
In the event of a breakdown

137
Fuse N°Rating Functions
F16 15


AFront foglamps.
F18 10


A
Right-hand main beam headlamp.
F1910 ALeft-hand main
beam headlamp.
F25 30
AHeadlamp washer
relay (after-market).
F29 40
AFront wiper motor.
12 V battery
Procedure for starting the engine using another
battery or charging a
discharged battery.
Lead-acid starter batteries
Batteries contain harmful substances
such as sulphuric acid and lead.
They must be disposed of in accordance
with regulations and must not, in any
circumstances, be discarded with
household waste.
Take used remote control batteries and
vehicle batteries to a
special collection
point.
Protect your eyes and face before
handling the battery.
All operations on the battery must be
carried out in a
well ventilated area and
away from naked flames and sources of
sparks, so as to avoid the risk of explosion
or fire.
Wash your hands afterwards. Versions equipped with Stop & Start are
fitted with a
12 V lead-acid battery of
specific technology and specification.
Its replacement should be carried out
only by a PEUGEOT dealer or a qualified
workshop.
With an automatic gearbox, never try to
start the engine by pushing the vehicle.
The Stop & Start system may not be
operational during the trip following the
next engine start.
In this case, the system will only be
available again after a


continuous
period of immobilisation of the vehicle,
a period which depends on the exterior
temperature and the state of charge of the
battery (up to about 8
hours).
Access to the battery
The battery is located under the bonnet.
To access it:
F
O
pen the bonnet using the interior release
lever, then the exterior safety catch.
F

S
ecure the bonnet stay.
8
In the event of a breakdown