boot Peugeot 208 2018 User Guide

49
12 V accessory socket
F To connect a 12 V accessory (maximum
power: 120 watts), lift the cover and plug in
the correct adapter.
Do not exceed the maximum power rating
of the socket (risk of damage to your
accessory).
USB socket
The USB socket allows the connection of
a portable device, such as an iPod®-type digital
audio player, or a

USB memory stick.
The USB reader reads your audio files, which
are then transmitted to your audio system and
played via the vehicle's speakers.
These files are managed via the steering wheel
controls or from the audio system.
When connected to the USB socket,
the portable device can be charged
automatically.
While charging, a message is displayed
if the power consumption of the portable
device exceeds the amperage supplied by
the vehicle.
Boot fittings
1.Rear shelf
2. Hooks
3. Boot lamp
4. Stowing rings (depending on version)
The connection of an electrical device
not approved by PEUGEOT, such as
a

USB charger, may adversely affect the
operation of vehicle electrical systems,
causing faults such as poor radio
reception or inter ference with displays in
the screens.
For more detail on the Audio equipment and
telematics, and particularly the USB socket,
refer to the corresponding part of the audio
equipment section. The USB socket also allows a
smartphone to
be connected by MirrorLink
TM, Android Auto®
or CarPlay®, so that certain applications on the
smartphone can be used on the touch screen.
3
Ease of use and comfort

57
Changing a wiper blade
This position permits release of the windscreen
wiper blades.
It is used for cleaning or replacing the wiper
blades. It can also be useful, in winter, to
release the wiper blades from the windscreen.
To move the wiper blades to the vertical position:
F O perate the wiper control stalk within one
minute after switching off the ignition to
position the wiper blades vertically on the
windscreen.
To return them to the park position:
F

S
witch on the ignition and operate the wiper
control stalk.
Removing a wiper blade
F Lift the corresponding wiper arm.
F U nclip and remove the wiper blade.
Fitting a new wiper blade
F Put the corresponding new wiper blade in place and clip it.
F

F
old down the wiper arm carefully. To maintain the effectiveness of the wiper
blades, it is advisable to:
-

h
andle them with care,
-
c
lean them regularly using soapy water,
-
a
void using them to retain cardboard on the
windscreen,
-
r
eplace them at the first signs of wear.
Rear wiper
Of f.
Intermittent wipe.
Wash-wipe (set duration).
If a

significant accumulation of snow or ice
is present, or when using a
bicycle carrier
on the boot, deactivate the automatic rear
wiper via the vehicle configuration menu
on the touch screen.
Reverse gear
When reverse gear is engaged, the rear wiper
will come into operation if the windscreen wiper
is operating.
The activation or deactivation of
operation of the rear wiper when
engaging reverse gear can be set in
the Driving/Vehicle menu.
4
Lighting and visibility

99
Deactivation/activation of the
front and rear parking sensors
Without touch screen
F To deactivate or activate the system, press this button.
The indicator lamp is illuminated when the
system is deactivated.
The deactivation or activation of
the function is done in the Driving/
Vehicle menu.
The function will be deactivated
automatically if a
trailer is being towed
or a
bicycle carrier is fitted (vehicle fitted
with a
towing device or bicycle carrier
recommended by PEUGEOT).
Operating limits
- Certain obstacles located in the sensors' blind spots may not be detected or no
longer be detected during the manoeuvre.
-

S
ounds such as those emitted by noisy
vehicles and machinery (e.g. lorries,
pneumatic drills, etc.) may inter fere with the
vehicle's sensors.
-

C
ertain materials (fabrics) absorb sound
waves: pedestrians may not be detected.
-

A
ccumulated snow or dead leaves on the
road sur face can inter fere with the vehicle's
sensors.
-

A f
ront or rear impact to the vehicle can
distort the settings of the sensors, which is
not always detected by the system: distance
measurements may be incorrect.
-

T
he tilting of the vehicle if the boot is
very loaded can affect the distance
measurements.
-

T
he sensors may be affected by poor
weather conditions (heavy rain, thick fog,
snowfall, etc.).
Maintenance
recommendations
In bad or wintry weather, ensure that the
sensors are not covered with mud, ice or
snow. When reverse gear is engaged, an
audible signal (long beep) indicates that
the sensors may be dirty.
High-pressure jet wash
When washing your vehicle, keep the
lance at least 12
inches (30 cm) away from
the sensors.
Operating fault
If a fault occurs when shifting
t o reverse, this warning lamp
comes on in the instrument panel,
accompanied by a
message and an
audible signal (short beep).
Contact a
PEUGEOT dealer or a qualified
workshop to have the system checked.
With touch screen
6
Driving

119
In the event of an AdBlue® breakdown,
confirmed by the message "Add AdBlue:
Starting impossible", you must top up with
at least 5

litres.
Never pour AdBlue
® into the Diesel fuel
tank.
For the specifics associated with the
access configuration for the AdBlue
® tank
(via the boot or via the fuel filler flap), refer
to the descriptions given in detail further
on.
If any AdBlue
® is splashed, or if there are
any spillages on the side of the body, rinse
immediately with cold water or wipe with
a

damp cloth.
If the fluid has crystallised, clean it off
using a

sponge and hot water.
Important: when topping up after
a breakdown due to running out
of AdBlue, you must wait for at least
5
minutes before switching on the ignition
again, without opening the driver's
door, unlocking the vehicle or inser ting
the key in the switch.
Switch on the ignition, then after
a
minimum of 10 seconds, start the engine.
F Switch off the ignition and remove the key from the switch to switch off the engine.
Access through the boot
(1.6 BlueHDi Euro 6.1)
F Raise the boot carpet then, depending on
equipment, lift out the spare wheel and/or
the storage box.
F

W
ithout pressing, turn the black cap
a
quarter turn anti-clockwise and lift it off.
F

T
urn the blue cap 1/6 of a turn anti-
clockwise.
F

L
ift off the cap.
Access through the fuel filler flap
(1.5 BlueHDi Euro 6.2)
Refilling
F Obtain an AdBlue® container or bottle. After
first checking the use-by date, read the
instructions on the label carefully before
pouring the contents of the container or
bottle into your vehicle's AdBlue tank.
Or F

W

ith the vehicle unlocked and the fuel filler
flap open, turn the blue cap of the AdBlue
®
tank 1/6

of a

turn anti-clockwise.
F

R

elease the blue cap.
F

I

nsert the AdBlue
® pump nozzle and refill
the tank until the nozzle stops automatically.
7
Practical information

120
Through the fuel filler flap
(1.5 litre BlueHDi Euro 6.2)
F Refit the blue cap to the tank filler and turn it
1/6 of a turn clockwise, to its stop.
F

C
lose the fuel filler flap.
Do not dispose of AdBlue
® bottles or
containers in the household waste.
Place them in a

suitable container or
take them to your dealer.
F

D

epending on equipment, return the spare
wheel and/or the storage box to the bottom
of the boot.
F

R

efit the boot carpet and close the tailgate.
Important:
-

T

o avoid over flowing the AdBlue
® tank,
it is recommended:
•

T

o top up between 10

and 13

litres
using AdBlue
® containers.
Or
•

I

f filling in a

ser vice station, stop
after the first automatic shut-off of
the nozzle.
-
I

f your vehicle's AdBlue
® tank is
completely empty – which is confirmed
by the alert messages and the
impossibility of starting the engine –
you must add at least 5

litres.
After refilling
Through the boot (1.6 BlueHDi
E u r o 6 .1)
F Refit the blue cap to the tank filler and turn it
1/6 of a turn clockwise, to its stop.
F

R
efit the black cap and turn it a quarter of
a
turn clockwise without pressing. Ensure
that the indicator on the cap lines up with
the indicator on the support.
Practical information

122
Temporary puncture
repair kit
Scan the QR code on page 3 to view
e xplanatory videos.
Comprising a
compressor and a sealant
cartridge, it allows the temporary repair of
a

tyre so that you can drive to the nearest
garage.
It is designed to repair most punctures which
could affect the tyre, located on the tyre tread
or shoulder.
Access to the kit
This kit is installed in the under floor storage,
under the boot floor. The vehicle's electric system allows the
connection of the compressor for long
enough to inflate a
tyre after a puncture
repair.
Composition of the kit
1. 12 V compressor, with integral pressure
gauge.
2. Sealant cartridge bottle, with integral hose.
3. Speed limit sticker.
Repair procedure
F Park the vehicle without obstructing any
traffic and apply the parking brake.
F

F
ollow the safety instructions (hazard
warning lamps, warning triangle, wearing
high visibility vest, etc.) according to the
legislation in force in the country where you
are driving.
F

S
witch off the ignition. F

U
ncoil the pipe stowed under the
compressor.
Avoid removing any foreign bodies which
have penetrated into the tyre.
F
C
onnect the pipe from the compressor to
the bottle of sealant.
F
T
urn the sealant bottle over and secure it in
the notch provided on the compressor.
In the event of a breakdown

125
Do not drive more than 125 miles (200 km)
w ith the repaired tyre; see a PEUGEOT
dealer or a
qualified workshop to change
the tyre.
Under-inflation detection
Should the pressure of one or more tyres
be adjusted, it is necessary to reinitialise
the under-inflation detection system.
For more information on Under-inflation
detection , refer to the corresponding
section. After a
tyre repair, this warning
lamp will remain on until the
system is reinitialised.
For more information on Under-inflation
detection , refer to the corresponding
section.Spare wheel
Scan the QR code on page 3 to view
e xplanatory videos.
Procedure for changing a


damaged wheel with
the spare wheel using the tools provided with
the vehicle.
Access to the tools List of tools
1.
Wheelbrace.
For removing the wheel trim and removing
the wheel fixing bolts.
2. Jack with integrated handle.
Used to raise the vehicle.
3. Bolt "cover" tool.
For removing the bolt protectors (covers)
on alloy wheels.
4. Socket for the security bolts.
For adapting the wheelbrace to the special
"security" bolts.
5. Towing eye.
For more information on To w i n g , refer to
the corresponding section.
The tools are installed in the boot under the
f l o o r.
To gain access:
F

o

pen the boot,
F

l

ift the floor and remove it,
F

r

emove the carrier box containing the tools.
8
In the event of a breakdown

126
Wheel with trim
When refitting the wheel, refit the trim
starting by placing its notch facing the
valve and press around its edge with the
palm of your hand.
All of these tools are specific to your
vehicle and may vary depending on
equipment.
Do not use them for any other purposes.
The jack must only be used to change
a wheel with a damaged or punctured tyre.
Do not use any jack other than the one
supplied with this vehicle.
If the vehicle does not have its original jack,
contact a
PEUGEOT dealer or a qualified
workshop to obtain the correct jack for it.
The jack meets European standards,
as defined in the Machinery Directive
2006/42/CE.
The jack does not require any
maintenance.
Access to the spare wheel
Removing the wheel
F Raise the spare wheel towards you from the r e a r.
F

T
ake the wheel out of the boot.
Putting the wheel back in place
F Put the wheel back in its housing.
F

S
lacken the nut on the bolt by a few turns.
F

P
osition the fixing device (nut and bolt) in
the middle of the wheel.
F

T
ighten fully until the central nut clicks, to
retain the wheel correctly.
F

P
ut the carrier box back in place in the
centre of the wheel and clip it.
If there is no wheel in the well, the fixing
device (nut and bolt) cannot be put back
in place.
The spare wheel is installed in the boot under
t h e f l o o r.
According to country, the spare wheel may be
steel, alloy or of the "space-saver" type.
F

Sl

acken the central nut.
F

R

emove the fixing device (nut and bolt).
In the event of a breakdown

129
After changing a wheel
To store the punctured wheel in the boot
correctly, first remove the central cover.
If your vehicle has a "standard" 15 -inch
spare wheel, do not exceed 50
mph
(80


km/h).
If your vehicle is fitted with 16
or 17-inch
wheels, use the "space-saver" type
spare wheel and do not exceed 50
mph
(80


km/h).
Visit a
PEUGEOT dealer or a qualified
workshop as soon as possible to have the
tightness of the bolts and the pressure of
the spare wheel checked.
Have the punctured tyre examined. After
inspection, the technician will advise you
on whether the tyre can be repaired or if it
must be replaced.Changing a bulb
The lamps have polycarbonate lenses with
a
protective coating:
F

d
o not clean them using a dr y or
abrasive cloth, nor with a
detergent
or solvent product,
F

u
se a sponge and soapy water or a pH
neutral product,
F

w
hen using a high-pressure washer
on persistent marks, do not keep the
lance directed towards the lamps or
their edges for too long, so as not to
damage their protective coating and
seals.
Changing a


bulb must only be done with
the ignition off and after the lamp has
been switched off for several minutes –
Risk of serious burns!
F

D
o not touch the bulb directly with your
fingers, use a
lint-free cloth.
It is essential only to use anti-ultraviolet
(UV) type bulbs, so as not to damage the
headlamp.
Always replace a
failed bulb with a new
bulb with the same type and specification. In some weather conditions (e.g. low
temperature or humidity), the presence
of misting on the internal sur face of the
glass of the headlamps and rear lamps is
normal; it disappears after the lamps have
been on for a
few minutes.
Light-emitting diodes (LED)
For the replacement of this type of bulb,
you must contact a
PEUGEOT dealer or
a


qualified workshop.
Halogen bulbs
To ensure good quality lighting, check
that the bulb is correctly positioned in its
housing.
8
In the event of a breakdown

132
F Insert a flat screwdriver between the door
mirror glass and its base.
F

T
ilt the screwdriver and use it as a lever to
extract the glass.
F

U
nclip the shell of the door mirror by
pressing on the two fixing clips.
F Press the central tab and remove the side repeater.
F

P
ull out the bulb holder and replace the faulty bulb.
To refit, carry out these operations in
reverse order.
To replace this type of bulb, you can also
contact a
PEUGEOT dealer or a qualified
workshop.
Rear lamps
1. Brake lamps (LED).
2. Reversing lamps (P21W).
3. Direction indicators (PY21W amber).
4. Sidelamps (LED).
5. Foglamp (P21W).
LEDs: light-emitting diodes.
Reversing lamps and direction
indicators
These two bulbs are changed from inside the
boot:
F

O
pen the boot. F

R
emove the access grille from the
corresponding side trim panel.
F
U
nscrew and remove the nut.
F
D
isconnect the lamp unit connector.
F
U
nclip the lamp unit and carefully extract it
pulling straight towards you.
Integrated direction indicator
side repeaters
F Press the four tabs and remove the bulb h o l d e r.
F

T
urn the bulb a quarter turn, pull it out and
fit a
new bulb.
To refit, carry out these operations in reverse
o r d e r.
In the event of a breakdown