key Peugeot 208 2018 Owner's Guide

119
In the event of an AdBlue® breakdown,
confirmed by the message "Add AdBlue:
Starting impossible", you must top up with
at least 5

litres.
Never pour AdBlue
® into the Diesel fuel
tank.
For the specifics associated with the
access configuration for the AdBlue
® tank
(via the boot or via the fuel filler flap), refer
to the descriptions given in detail further
on.
If any AdBlue
® is splashed, or if there are
any spillages on the side of the body, rinse
immediately with cold water or wipe with
a

damp cloth.
If the fluid has crystallised, clean it off
using a

sponge and hot water.
Important: when topping up after
a breakdown due to running out
of AdBlue, you must wait for at least
5
minutes before switching on the ignition
again, without opening the driver's
door, unlocking the vehicle or inser ting
the key in the switch.
Switch on the ignition, then after
a
minimum of 10 seconds, start the engine.
F Switch off the ignition and remove the key from the switch to switch off the engine.
Access through the boot
(1.6 BlueHDi Euro 6.1)
F Raise the boot carpet then, depending on
equipment, lift out the spare wheel and/or
the storage box.
F

W
ithout pressing, turn the black cap
a
quarter turn anti-clockwise and lift it off.
F

T
urn the blue cap 1/6 of a turn anti-
clockwise.
F

L
ift off the cap.
Access through the fuel filler flap
(1.5 BlueHDi Euro 6.2)
Refilling
F Obtain an AdBlue® container or bottle. After
first checking the use-by date, read the
instructions on the label carefully before
pouring the contents of the container or
bottle into your vehicle's AdBlue tank.
Or F

W

ith the vehicle unlocked and the fuel filler
flap open, turn the blue cap of the AdBlue
®
tank 1/6

of a

turn anti-clockwise.
F

R

elease the blue cap.
F

I

nsert the AdBlue
® pump nozzle and refill
the tank until the nozzle stops automatically.
7
Practical information

140
Quick-release terminal clamp
Disconnecting the (+) terminalReconnecting the (+) terminal
Do not force the lever as locking will not
be possible if the clamp is not positioned
correctly; start the procedure again.
Before disconnecting
Wait 2 minutes after switching off the ignition
b efore disconnecting the battery.
Close the windows and the doors before
disconnecting the battery.
Following reconnection
After each time that the battery has been
reconnected, switch on the ignition and wait
1
minute before starting the engine, to allow
the electronic systems to initialise. However,
if minor problems persist after this procedure,
contact a
PEUGEOT dealer or a qualified
workshop.
Referring to the corresponding section, you
must yourself reinitialise:
-

t
he remote control key,
-

t
he date and time,
-

t
he radio preset stations.
F

Ra

ise the lever A fully to release the
clamp B .
F

R

emove the clamp B by lifting it off. F

Ra

ise the lever A fully.
F

R

efit the open clamp B on the (+) terminal.
F

P

ush the clamp B fully down.
F

L

ower the lever A to lock the clamp B .
To w i n g
Procedure for having your vehicle towed or for
towing another vehicle using the towing eye.
F

s

witch off all electrical consumers (audio
system, wipers, lighting, etc.),
F

s

witch off the ignition and wait for 4

m

inutes.
At the battery, it is only necessary to
disconnect the (+) terminal.
In the event of a breakdown

141
General recommendations
Obser ve the legislation in force in the
country where you are driving.
Ensure that the weight of the towing
vehicle is higher than that of the towed
vehicle.
The driver must remain at the wheel of
the towed vehicle and must have a valid
driving licence.
When towing a
vehicle with all four wheels
on the ground, always use an approved
towbar; rope and straps are prohibited.
The towing vehicle must move off gently.
When the vehicle is towed with its engine
off, there is no longer braking and steering
assistance.
In the following cases, you must always
call on a
professional recovery ser vice:
-

v
ehicle broken down on a motor way or
fast road,
-
f

our-wheel drive vehicle,
-

w
hen it is not possible to put the
gearbox into neutral, unlock the
steering, or release the parking brake,
-

w
hen it is not possible to tow a vehicle
with an automatic gearbox, engine
running,
-

t
owing with only two wheels on the
ground,
-

w
here there is no approved towbar,
etc. available.Access to the tools
Towing your vehicle
The towing eye is installed in the boot under
t h e f l o o r.
To gain access:
F

o
pen the boot,
F

l
ift the floor and remove it,
F

r
emove the towing eye from the carrier box.
F

O
n the front bumper, unclip the cover by
pressing at bottom right.
F

S
crew the towing eye in fully.
F

I
nstall the towbar. F

P
lace the gearbox in neutral.
F

ailure to follow this instruction may
cause damage to some components
(braking, transmission, etc.) and the
absence of braking assistance when
the engine is restarted.
F
U
nlock the steering by turning the ignition
key one notch and release the parking
brake.
F S witch on the hazard warning lamps on
both vehicles.
F

M
ove off gently, drive slowly and for a short
distance.
Towing another vehicle
F On the rear bumper, unclip the cover by pressing at the bottom.
F

S
crew the towing eye in fully.
F

I
nstall the towbar.
F

S
witch on the hazard warning lamps on
both vehicles.
F

M
ove off gently, drive slowly and for a short
distance.
8
In the event of a breakdown

5
Select a line in the list.
C onfirm with " OK".
Return to the top level of the folder structure to
select the type of tracks.
-

By Folders (CD or USB): all folders
containing audio files recognised on the
peripheral device, in alphabetical order
without following the folder structure.
-

By Artist (USB only): all of the artist names
defined in the ID3


Tags, in alphabetical
o r d e r.
-

By Genre (USB only): all of the genres
defined in the ID3
Tags.
-

By Playlist (CD or USB): if playlists have
been saved.
Information and advice
The audio system will only play files with
".mp3", ".wma" and ".wav" extensions on a CD
and can play files with ".ogg" extension only on
USB.
File names should have less than
20


characters, avoiding special characters
(e.g. " ?; ù) so as to avoid any reading or
display problems. If the disc is burned in another format, it may
not be played correctly.
It is recommended that the same burning
standard is always used on an individual disc,
with the lowest speed possible (4x maximum)
for the best acoustic quality.
In the particular case of a
multi-session CD, the
Joliet standard is recommended.
The playlists accepted on CD, MP3, iPod and
USB connection are types ".m3u" and ".wpl".
The system can recognise up to 5,000 files in
500 folders on 8 levels.
On a single disc, the CD player can read up
to 255 MP3 files spread over 8 folder levels
with a maximum of 192 folders. However, it
is recommended that the number of levels is
limited to 2 so as to reduce the time taken to
access and play the CD.
The folder structure is not obser ved during
playback.
Do not connect a hard disk or USB device other
than audio players to the USB socket. This may
cause damage to your installation.
Use only USB memory sticks formatted to FAT
32
(File Allocation Table).To protect the system, do not use a
USB
hub.
Bluetooth® audio streaming
Streaming allows music files on a telephone to
b e heard via the vehicle's speakers.
Connect the telephone: see the " Telephone"
section.
In the " Bluetooth: Audio " menu, select the
telephone to be connected.
The audio system connects to a
newly paired
telephone automatically.
Activate the streaming source by
pressing the SRC/TEL button.
In certain cases, play of the audio
files must be initiated from the
keypad.
The control of common tracks is possible
via the audio system control buttons and the
steering mounted controls, if the telephone
supports the function.
Contextual information can be displayed in the
screen.
The audio quality depends on the quality of
transmission by the telephone. It is recommended that you use genuine
Apple
® USB cables for correct operation.
In order to be able to play a

burned CDR or
CDRW, select standards ISO

9660

level 1, 2

or
Joliet if possible when burning the CD.
.
Bluetooth® audio system

6
Connecting Apple® players
Connect the Apple® player to the USB socket
using a
suitable cable (not supplied).
Play starts automatically.
Management of the device is via the audio
system controls.
The classifications available are those of the
portable device connected (artists/albums/
genres/playlists/audiobooks/podcasts).
The version of software in the audio system
may not be compatible with the generation of
your Apple
® p l aye r.
Telephone
Pairing a Bluetooth®
telephone
As a safety measure and because it
r equires sustained attention by the driver,
the pairing of a
Bluetooth mobile telephone
with the Bluetooth hands-free system of
your audio system must be done with the
vehicle stationary and the ignition on.
Visit www.peugeot.co.uk for more information
(compatibility, additional help, etc.).
Activate the telephone's Bluetooth function and
ensure that it is set as visible to all (refer to the
telephone user guide).
Press the MENU button.
Select " Bluetooth ".
Select " Search".
A window is displayed with " Searching for
device ". The services available depend on
the network, the SIM card and the
compatibility of the Bluetooth devices
used.
Check the user guide for your telephone
and with your ser vice provider for the
ser vices to which you have access.
In the list, select the telephone to
pair.
Confirm with " OK".
Only one telephone can be paired at a time.
In some cases, the Bluetooth address of the telephone
may appear instead of the name of the telephone.
A virtual keypad is displayed on the
screen: choose a
4-digit code.
Confirm with " OK".
A message is displayed on the screen of the
telephone: enter the same code and confirm.
If pairing fails, the number of attempts is not
restricted.
A message appears on the screen to confirm
that the connection is successful. Pairing can also be initiated from the
telephone by searching for the Bluetooth
devices detected.
Bluetooth® audio system

6
Managing messages
Press Applications to display the
primary page.
Press "SMS".
Select the "SMS" tab.
Press this button to select the
display settings for messages.
Press this button to search and
select a


recipient.
Select the "Quick messages" tab.
Press this button to select the
display settings for messages.
Press this button to write a
new
message.
Press the basket alongside the
selected message to delete it.
Press this button alongside the
selected message to display the
secondary page. Press this button to edit and modify
the existing text.
Press this button to write a
new
message.
Press the basket to delete the
message.
Radio
Selecting a station
Press Radio Media to display the
primary page.
Press one of the buttons for an
automatic search for radio stations.
Or Move the slider for a
manual search
for frequencies up or down.
Or Press the frequency.
Enter the FM and AM waveband
values using the virtual keypad. Press "
OK" to confirm.
Radio reception may be affected by the
use of electrical equipment not approved
by the Brand, such as a USB charger
connected to the 12 V socket.
The exterior environment (hills, buildings,
tunnels, basement car parks, etc.) may
block reception, including in RDS mode.
This is a normal effect of the way in which
radio waves are transmitted and does not
indicate any failure of the audio system.
Changing waveband
Press Radio Media to display the
primary page.
Press the " OPTIONS" button to go to the
secondary page.
Press "Band" to change waveband.
Press in the grey zone to confirm.
PEUGEOT Connect Radio

15
Press on the name of the telephone
chosen in the list to disconnect it.
Press again to connect it.
Deleting a telephone
Press the basket at the top right
of the screen to display a
basket
alongside the telephone chosen.
Press the basket alongside the
telephone chosen to delete it.
Receiving a call
An incoming call is announced by a ring and
a superimposed display in the screen.
Make a
short press on the steering
mounted PHONE button to accept
an incoming call.
And Make a
long press
on the steering mounted PHONE
button to reject the call. Or
Press "End call".
Making a call
Using the telephone is not recommended
while driving.
Parking the vehicle.
Make the call using the steering mounted
controls.
Calling a new number
Press Telephone to display the
primary page.
Enter the phone number using the
digital keypad.
Press " Call" to start the call.
Calling a contact
Press Telephone to display the
primary page.
Or make a
long press
on the steering mounted TEL button.Press "
Contacts ".
Select the desired contact from the list offered. Press "Call".
Calling a recently used
n umber
Press Telephone to display the
primary page.
Or Make a
long press
on the steering mounted button.
Press " Recent calls ".
Select the desired contact from the list offered.
It is always possible to make a
call directly
from the telephone; as a
safety measure,
first park the vehicle.
Setting the ringtone
Press Telephone to display the
primary page.
.
PEUGEOT Connect Radio

16
Press the "OPTIONS" button to go to the
secondary page.
Press "Ring volume " to display the
volume bar.
Press the arrows or move the slider
to set the ring volume.
Settings
Setting profiles
As a safety measure and because it
r equires the sustained attention of the
driver, changes to settings must only be
done with the vehicle stationary .
Press Settings to display the
primary page.
Press " Profiles ".
Select " Profile 1 " or "Profile 2 " or "Profile 3 "
or " Common profile ".
Press this button to enter a
name for
the profile using the virtual keypad.
Press " OK" to save. Press the back arrow to confirm.
Press this button to activate the
profile.
Press the back arrow again to
confirm.
Press this button to initialise the
profile selected.
Adjusting brightness
Press Settings
to display the
primary page.
Press Brightness .
Move the slider to adjust the brightness
of the screen and/or of the instrument
panel (according to version).
Press in the grey zone to confirm.
Modifying system settings
Press Settings to display the
primary page. Press "
Configuration " to go to the
secondary page.
Press " System configuration ".
Press the " Units" tab to change the units of
distance, fuel consumption and temperature.
Press the " Factory settings " tab to return to
the initial settings.
Returning the system to factory settings
activates the English language by default
(depending on version).
Press the " System info " tab to display the
versions of the different modules installed in
the system.
Press the " Privacy" tab,
or Press Settings to display the
primary page.
Press " Privacy " to activate or
deactivate the privacy data mode.
PEUGEOT Connect Radio

17
Activate or deactivate:
- "No sharing (data, vehicle
position) ".
-
"Data sharing only "
-
"Sharing data and the vehicle
position "
Press the back arrow to confirm.
Press Settings to display the
primary page.
Press " Configuration " to go to the
secondary page.
Press " Screen configuration ".
Press " Brightness ".
Move the slider to adjust the brightness
of the screen and/or of the instrument
panel (according to version).
Press the back arrow to confirm.
Press " Animation ".
Activate or deactivate: " Automatic
text scrolling ".
Select " Animated transitions ".Press the back arrow to confirm.
Selecting the language
Press Settings
to display the
primary page.
Press " Configuration " to go to the
secondary page.
Select " Language " to change the
language.
Press the back arrow to confirm.
Setting the time
Press Settings to display the
primary page.
Press " Configuration " to go to the
secondary page.
Press " Date and time ".
Select " Time". Press this button to adjust the time
using the virtual keypad.
Press "
OK" to save the time.
Press this button to define the time
zone.
Select the display format for the time
(12 h / 24 h).
Activate or deactivate summer time
(+1

h o ur).
Activate or deactivate
synchronisation with GPS (UTC).
Press the back arrow to save the
settings.The system does not automatically manage
the change between winter and summer
time (depending on the country of sale).
Setting the date
Press Settings to display the
primary page.
.
PEUGEOT Connect Radio

11
Navigation
Choice of a destination
To a new destination
Press Navigation to display the
primary page.
Press the " MENU" button to go to the
secondary page.
Select "Enter address ".
Select the " Country".
Enter the " City", the " Street " and the
" Number " and confirm by pressing
on the suggestions displayed.
Press " OK" to select the " Guidance
criteria ".
And/or Select "See on map " to select the
" Guidance criteria ".
Press " OK" to start navigation. Zoom out /in using the touch buttons or
with two fingers on the screen.
In order to be able to use the navigation,
it is necessary to fill in the "
City", the
" Street " and the " Number" on the
virtual keyboard or take it from the
list in " Contact " or in the " History" of
addresses.
Without confirmation of the street number,
you will be guided to one end of the street.
To a recent destination
Press Navigation to display the
primary page.
Press the " MENU" button to go to the
secondary page.
Select "My destinations ".
Select the " Recent" tab.
Select the address chosen in the list to display
the " Guidance criteria ". Press "
OK" to start navigation.
Select " Position " to visualise the arrival
point geographically.
To "My home " or "My work "
Press Navigation to display the
primary page.
Press the " MENU" button to go to the
secondary page.
Select "My destinations ".
Select the " Preferred" tab.
Select " My home ".
Or Select "My work ".
Or
Select a


preset favourite destination.
.
PEUGEOT Connect Nav